Introducción
Utilizar esta guía para reemplazar un panel de vidrio de la pantalla frontal roto. Se requiere la extracción del cristal de la pantalla frontal para acceder a la pantalla LCD.
Qué necesitas
-
-
Retira los siguientes 10 tornillos que sujetan la tapa inferior del MacBook Pro 13 "Unibody:
-
Siete tornillos Phillips de 3 mm.
-
Tres tornillos Phillips de 13,5 mm.
-
-
-
Levanta ligeramente la tapa inferior y empuja hacia la parte posterior para liberarlo de las pestañas que lo sujetan
In the introduction you should link fixers to this excellent doc: https://www.ifixit.com/Misc/HD_Software_...
It is really critical, super easy, and free(!) to clone your existing drive onto the new one you will install. I ran into one error, but SuperDuper! support replied immediately on how to fix it...Thanks ifixit and SuperDuper! (I ponied up the $28 for the software anyway, I was so impressed!)
Long story short: I drank the AppleKoolAid back in 1984 and have always left the guts of my machines up to Apple - until recently when I needed to swap the SATAs from my original MacDaddy (2009 13" MBPro that I killed in 2018 - coffee + blackout = OOOOPS) into a pristine 2009 MBPro from a Goodwill in North Carolina through eBay. I need the files from iCal and MacMail that can't be opened in my newer machines.
Well . . . I ain't never done nuttin' like that, before!
Enter Luke Miani on YouTube. He raves about you guys! So, I watched everything I could, read your site, bought the right tools and at the ripe old age of 72, I sat down, this morning and did the work. Now my original MacDaddy lives in MacDaddy2.0.
Am I allowed to cry?
Seriously, I can't thank you enough for your bitchen site and killer tools. I wish I'd'a been turned on to this shizzle 30+ years ago.
IFIXIT - IDIGIT!
HAHAHAHAHAHAHAHAHAHA.
That was a brilliant read.
Yes, I came across ifixit a few years ago. Totally helped me out on several occasions.
Glad your Mac repair journey worked out.
:)
Cary B -
-
-
-
Utilice el extremo plano de un spudger para levantar el conector de la batería hacia arriba fuera de su toma en la placa lógica.
How do you get that battery connector back on? Do you just press it in back in place after you're done?
yes. I usually plug it in before I screw it down so I can lift the battery a bit and have enough slack to be able to go straight down on the connector, otherwise it comes in on a bit of an angle, which can't be good (though not necessarily bad).
This step almost finished me, and I did extensive damage to the battery plug. Fortunately, I later replaced the battery, and the replacement came with a new plug! :) Newbies need to know - 1. The battery plug is like a thin lip on a thicker lip, so you need to pry BETWEEN 2 thin lips to get it off, else you are trying to yank out the socket. 2. Mine was initially VERY tight, and trying to get it out broke the plastic on all sides of plug, even though I was as careful as possible. Luckily, this didn't hurt functionality and I later replaced the battery. AFTER disconnecting once, it was never so tight again,
-
-
-
Utilice el extremo plano de un spudger para mover el subwoofer / conector del cable del altavoz derecho hacia arriba fuera de su zócalo en la placa lógica.
Please Be Carefully With This Step, Because I Had To Resolder It Back To The Logic Board. But There Is A Black Foam Piece Over The Cable You Have To Pry Up, Lift The Foam Piece And Then Try To CAREFULLY Pry Cable Connector
-
-
-
Desconecta el cable de la cámara deslizándolo horizontalmente fuera de su zócalo.
-
Si ves un pequeño retenedor de plástico adherido a la placa lógica que evita que el cable de la cámara se deslice, quítalo con cuidado de la placa lógica. Aplica un poco de calor con un secador de pelo o una pistola de aire caliente si es necesario para ayudar a suavizar el adhesivo que lo mantiene en su lugar.
-
No intentes desconectar a la fuerza el cable con el retenedor en su lugar.
-
Si aún tiense problemas, usa la punta de un spudger para empujar cada lado del conector y "camina" lentamente para sacarlo de su zócalo.
This step is unnecessarily tricky. I’ve tried to make it better by adding images highlighting the plastic stopper thingy and showing a clear arrow of the direction the cable should be pulled.
However, simply pulling the cable may not be enough to remove it. It sure wasn’t for me. I think there ought to be a close-up of the two little nubbins on the sides of the plug which one uses to wiggle it loose from the connector by gently prying with a tiny flathead screwdriver. I didn’t add that tip because (a) it would have made the instructions longer, (b) I didn’t think to take a photo of it, and (c) using a screwdriver carelessly next to the logic board could scratch or break components on the motherboard. A guitar pick or very small spudger might work.
@hackerb9 Thanks for your edits and comments! I took some additional shots and tried to clean this up a little for everyone. There should be a lot less confusion now. Interestingly, neither of the two MacBook Pros used for these guides had the plastic retainer piece you folks mentioned, but I left that image in a link so everyone can still see what it looks like if needed.
Thanks for incorporating some of my edits and for taking new photos.
Are you the one who took the original photographs? If so, you did originally have the hard plastic retainer as it was in those photos, just obscured by your thumbnail. The glue on the retainer allows it to shift a bit, so it's possible you took out the cable and knocked off the retainer without noticing it.
Your two frame animation of pulling out the plug is helpful to show the proper direction. Given the number of people who have destroyed their MacBooks from this procedure, I think we should do even better. The instruction would be clearer if it said, “Disconnect the camera cable by sliding it horizontally out of its socket.”
Also, if you can post a link to a picture without fingers in the shot, I will add an arrow showing the proper direction. (I would have added it to the original, but visually it would have gone through your fingers.)
P.s. this isn't as important, but where did you hear the tip about the hairdryer? I'd leave that out as firmly peeling it up works fine.
hackerb9 -
Negative, I’m not the original photographer. You’re right, I do see the retainer in some of the previous photos, although it wasn’t in any of the images for this particular step. May have been an oversight on the part of the original author! So I’m glad you caught it. I updated the verbiage as you requested. Don’t worry about adding arrows—at this point, if someone ignores both the images and the multiple warnings in the text, that’s no longer a fault with the guide. The heat/hairdryer tip is standard practice for anything that’s secured with adhesive—I hardly ever work on a MacBook of any vintage without using a heat gun at least a couple times. It may not be strictly necessary, but the result is much cleaner and it reduces the risk of accident.
-
-
-
Retire los siguientes tornillos que sujetan el cable de datos de la cámara y el altavoz derecho a la caja superior:
-
Dos tornillos Phillips de 8 mm.
-
Un tornillo Phillips de 4mm.
-
Resbala el soporte del cable de la cámara hacia afuera desde debajo del subwoofer y retírelo del la computadora.
-
-
-
Agarre la lengüeta de tracción de plástico asegurada al bloqueo del cable de datos de la pantalla y gírela hacia el lado DC-in del equipo.
-
retire el conector del cable de datos de la pantalla directamente de su toma.
Well, my display ended up looking like this after the repair:
http://i1106.photobucket.com/albums/h366...
As you can see, there was a light/dark banded pattern along the bottom of the screen, corresponding to the LCD's backlight. In my case it was also accompanied by a constant high pitched whistling noise. I swear to anything that's holy, it was not coming from the fan or the speaker, but rather the motherboard itself.
Anyway, both these problems went away when I disconnected and reconnected the connector at this stage. I'm saying this on the off chance it helps someone else.
It's not to clear but there is a piece of spring steel that rotates away from the main (circuit board side) of the connector....this piece sort of hugs the parameter of the screen cable locking it to the circuit board...both arms wrapped around your brother....looking closely (10x magnifier) at this cable one of the gold connections is slightly oxidized---my display arbitrarily flickers and this symptom is lessened as the temperature increases...I suspect this is the cuase of the screen flashing on/off
-
-
-
-
Usa tu destornillador Torx para quitar los dos tornillos exteriores de 6,5 mm que sujetan cada uno de los dos soportes de la pantalla a la carcasa superior (4 tornillos en total).
Hey folks, regarding the screw/driver sizes: there are separate guides for the Mid 2010 model with the T8 screws. Always use the correct guide for your model to avoid confusion, stripped screws, etc. Hope this helps!
-
-
-
Abra su MacBook para que la pantalla sea perpendicular a la mayúscula.
-
Coloque su MacBook abierto en una mesa como se ilustra.
-
Mientras sujetas la pantalla y la carcasa superior con la mano izquierda, utiliza el destornillador Torx para quitar el tornillo restante de 6,5 mm del soporte inferior de la pantalla.
-
-
-
Retira el último tornillo Torx de 6 mm que fija la pantalla en la parte superior.
Removing the screen assembly this way, with the computer standing on edge, is needlessly risky and difficult. By the 5th or 6th time I did this procedure (of perhaps a hundred), it dawned on me that there’s a way, way easier method for the whole lid removal job: 1. After removing the bottom cover and disconnecting power, hang the open laptop, keyboard down, facing away, over the edge of your work table with the lid assembly hanging down, monitor facing toward the table and pushed against the table edge. (If you’re klutzy, tape the main body to the table so it can’t slide around.) 2. With the unit positioned this way, you can easily disconnect the various cables & remove the 6 hinge screws. Now the lid assembly will just be hanging, easy to lift away from the main body without difficulty or danger. 3. Reverse this to put it back together.
Nice tip, Clinton! I’ll have to try that next time. Do you have photos of how it is done so this guide can be updated?
hackerb9 -
-
-
-
Levante la pantalla hacia arriba y lejos de la parte superior, teniendo en cuenta los soportes o cables que pueden quedar atrapados.
Re-assembly hint: Laying the base, keyboard down, on a table top with the hinge side over the edge about 1/2" toward you is a more stable position for re-assembly than trying to do this up on its edge. This has the added benefit of being able to reinsert the torn screws vertically.
May be in the wrong place but then please direct me. At this step, can I just take off the upper half (meaning the screen, LCD, and top housing shell in one) and simply replace it with another upper half of the same edition???
Yes, you can. Thanks what I'm doing now. :)
-
-
-
Con la pistola de aire caliente en posición baja, comience calentando el borde exterior negro cerca de la esquina superior derecha del panel de vidrio.
With a lot of heating, for me, it was very hard to get the glass to separate from the case. I had better luck starting from the bottom right as I could grip better onto the case. Three mistakes I made:
1. Once I got the glass separated, I probably didn't heat sufficiently as I was going around and the glass broke. That made the rest of the procedure miserable. Lesson: pull very gently.
2. I must have touched one of the tiny bits of glass that fell on the LCD and it scratched the actual screen. :-(. Lesson: vacuum the pieces as you go and be very careful when touching the LCD.
3. I somehow overheated the LCD screen at the top left and right corners and now the display is all wonky and faded at the corners. Not sure what the lesson is here.
First, if using a hair dryer, what setting should that be operated at? It would be much cooler than the heat gun, right?
Second, the iFixit basic set comes with a small, clear suction cup. Would that be sufficient for this project, or does it require the stronger pull of the other cups?
Finally, must I reapply adhesive to the case when replacing the glass? Does the original remain tacky and re-bond on assembly?
It's been a while since you asked, but since no one answered and someone else may have the same questions:
Hair dryers vary a lot, depending on wattage. I would start on low or med, and work my way up to high if necessary. I'd keep the fan on the lowest setting.
The little suction cup is for removing screens like the iMac, which just uses magnets, and possibly an iPad or iPhone. I would not want to use that for this project, get something about 2" wide with a decent handle.
The screen should have the double sided glue tape already applied, just remove the backing. I wouldn't get glass that doesn't have the tape on it, big waste of time with little savings in cost.
Jeff Kamis
All I can say for this is don't be tempted to hold the heat gun too close. I ended up burning my LCD the first time I did it and having to replace that when all I was looking to do was replace the cable. I got the glass off holding it about 4/5 inches from the screen and being patient (it took about 5/10 minutes in the end).
The tape is very sticky and the glass is very fragile but at the same time fairly flexible.....I ended up breaking the glass ans it turned out to be a mess picking up the shards....but in the end a new glass is not too costly. the implication is that heating melts the glue but it is really just double stick tape.....there are some "youtube" videos that are worth a look but I would suggest using guitar picks and not a putty knife which creates a point load that breaks the glass....wear safety glasses!!
Be ready to replace the glass (good thing mine was already broken, I ordered one). Wear surgery gloves and protective glasses. Trust your nose, if it smell melted plastic, it’s a good clue to stop the heat.
If you have a glass cover that is severely cracked then the heating gun and suction cup procedure really doesn’t work. Suction cups won’t hold and the already broken glass doesn’t lift. Here’s what I did that made the job easier. Using 2 inch wide transparent packing tape I laid it along the perimeter of the display but not covering the rubber edge. Then I used a 1/4 inch wood carving tool and very carefully removed the glass and 2 sided tape around the metal border. Use as your guide picture 2 in this step that shows where the camera and cable is located. Where the camera is located in the top center the 2 sided tape isn’t located so you can easily lift the glass. The camera cable runs up the right side in a trough in the metal border so when lifting the tape and glass in this area just keep the sharp end flat and it is wide enough it won’t dip into the trough and damage the cable. The tape was very helpful because it kept the glass from splintering and going everywhere.
-
-
-
Con el panel suficientemente caliente, fije una ventosa de servicio pesado cerca de la esquina superior derecha del cristal de la pantalla.
-
Lentamente y con cuidado, tire de la esquina del cristal de la pantalla hacia arriba del conjunto de la pantalla.
-
-
-
Levante suavemente la esquina del cristal de la pantalla lo suficiente para insertar un spudger entre el mismo y el conjunto de la pantalla.
-
Utilice el extremo plano de un spudger para levantar suavemente el adhesivo que sujeta el cristal frontal a la pantalla.
-
Levante el panel de vidrio a unos centímetros de la esquina superior derecha a lo largo de los bordes superior e inferior de la pantalla.
-
-
-
Utilice una pistola de calor para ablandar el adhesivo debajo de la franja negra a lo largo del lado derecho del panel de vidrio delantero.
-
Sujete una ventosa a lo largo del lado derecho del panel de vidrio delantero.
-
Tire hacia arriba en el panel de vidrio mientras utiliza el extremo plano de un spudger para separarlo del resto del conjunto de la pantalla.
-
Continúe trabajando a lo largo del borde derecho del cristal de pantalla frontal hasta que se separe de la pantalla.
I ended up breaking my glass panel due to using the spudger. I think if you use something more like a small putty knife you will do better. The spudger puts a lot of pressure in a small spot while the putty knife would put a little pressure over a larger area. Also, if you do break the glass, be sure to get ALL of the broken bits off before putting the new one on. Also, watch out for those broken bits as they tend to penetrate skin quite easily, and stay there for days!
-
-
-
Utilice su pistola de calor para suavizar el adhesivo debajo de la franja negra a lo largo del borde superior del panel de visualización de cristal.
-
Coloque una ventosa cerca del borde superior del panel de cristal y utilícela para extraer el panel de vidrio de la pantalla.
-
Trabajar a lo largo del borde superior del panel de vidrio, con cuidado utilizando el extremo plano de un spudger para separar el adhesivo si es necesario.
-
-
-
Utilice una pistola de calor para ablandar el adhesivo debajo de la tira negra cerca de la esquina superior izquierda del panel de visualización de cristal.
-
Coloque una ventosa cerca de la esquina superior izquierda del panel de cristal.
-
Tire hacia arriba de la ventosa y use el extremo plano de un spudger para sacar cuidadosamente el panel de visualización de cristal fuera del conjunto de la pantalla.
-
-
-
Utilice una pistola de calor o secador de pelo para suavizar el adhesivo debajo de la franja negra a lo largo del lado izquierdo del panel de vidrio frontal.
-
Conecte una ventosa a lo largo del lado izquierdo del panel de vidrio delantero.
-
Tire hacia arriba en el panel de vidrio mientras utiliza el extremo plano de un spudger para separarlo del resto del conjunto de la pantalla.
-
Continúe trabajando a lo largo del borde izquierdo del cristal de pantalla frontal hasta que se separe de la pantalla.
-
-
-
Para volver a conectar el cable, primero use la punta de un spudger para quitar el pedazo de cinta de espuma sobre el zócalo ZIF del cable de la cámara.
-
Utilice la punta de un spudger para levantar el retenedor del cable ZIF en el zócalo del cable de la cámara.
-
Inserte el cable de la cámara en su toma en la placa de la cámara y utilice la punta de un spudger para encajar el retén del cable ZIF, bloqueando el cable en su lugar.
-
Para volver a armar su aparto, siga estas instrucciones en orden inverso.
Para volver a armar su aparto, siga estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
52 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
Un comentario
This guide needs to be replicated / linked on to all the other A1286 13-inch Unibody models as it was done with the 2010 model. The screens are the same for each year of the A1286 generation from 2009, 2010, early 2011, late 2011, and 2012.
Ideally, it could be really helpful if the staff team can improve the article; improve on the steps outlined; using the feedback received in the comments - e,g, safer ways to handle broken glass, use of solvents like alcohol or acetone to dissolve / neutralise the adhesive seal, and ways to preserve the rubber lining, the LCD panel itself, and the additional circuitry & cabling underneath.
Compare the short screws carefully before reinstalling them. The shouldered screws go in the holes on the front edge.
David Kilbridge - Contestar
Before I started removing any screws I took a piece of paper and drew the bottom of the laptop and put a piece of double-sided tape in the spot where each screw goes. That way when I took out the screws, I could put them on the tape so I knew exactly which screw went in which spot. I did the same thing for dismantling the inside on another sheet of paper, then a third sheet for the screen after getting the front glass off.
mastover - Contestar
I use a similar technique: I print out the iFixit manual for the job, and Scotch-tape down the screws/brackets/cables I remove at each step next to the component descriptions. That way, when I'm reassembling, the bits are taped right next to the photo of where they came from.
adlerpe -
That's exactly what I do for all my repairs! It's the best way to keep track of all of the parts ' original location and to make sure that you don't miss any parts during reassembly.
joyitsjennie -
Great idea and one I use often
Thomas Overstreet -
Excellent idea! Thanks for sharing it here.
Laura Sharkey -
I used a 00 that fit but the screws were very tight so I used a tiny paintbrush with some wd40 on it and put it around the edges of the screws. Worked like a charm
valentinedhdh - Contestar
I use a magnetic mat and place the screws in order on that :)
Cary B - Contestar