Este perfil no está completo aún.
Preguntas
The issue I have is it only turns on when the power cable is plugged in, if I take it out it turns off immediately. When I...
Leer másI've looked for parts and I can't seem to find them anywhere, I see plenty of sellers selling the 5th and 6th LCD's as...
Leer másWe’ll be receiving a large quantity of iPhone 13’s from our clients shortly, I know that information will be stored in the...
Leer másWe’ve repaired housings on iPhone’s for quite a while now, all of a sudden recently we are finding that we are having...
Leer másMyself and other technicians are having issues where on the above models, when we move the home button from the broken...
Leer másDoes anybody have the screw sizes for the volume buttons or have reference to where I can find them? I don’t want to be...
Leer másSo I’m just about to replace the back glass on an iPhone XR that I bought. I’ve seen a couple of people gutting the phone...
Leer másSo a family member gave me an iPhone 7 to repair and upon inspection the screen had popped out, this was due to the...
Leer másSo I`ve just bought a 3G to add to my ever growing iPhone collection. I`ve set the phone up and all is working normally...
Leer másRespuestas
I’ve had this problem before and 100% its the touch flex cable. It’s quite possible that you have gotten faulty parts, It’s happened to me before that multiple parts have been faulty. On the other hand make sure you are lining up the cables correctly when installing the back plate. If they are out by a little bit it can cause a sharp bend in the flex causing the touch issues you’re having. The cables on the third party screens are very thin and easily damaged so just make sure they’re lined up correctly and that you’re not applying too much pressure when installing the back plate.
Leer másPush the top two prongs in at an angle, then walk down the phone with your thumbs pressing on the bezels. Also I would recommend applying a new water adhesive seal (If you haven’t already) as it will keep everything in place. If neither of those work, send it back and get another replacement screen assembly.
Leer másIt sounds to me that the replacement part you have is faulty. Have you also checked to see if the speaker is working? If not then its definitely defective as all those components run off the charge flex.
Leer másThe x1 and x2 are two separate cameras, perhaps the x2 unit is faulty. You would need a complete new camera unit as you cant just replace one of the cameras. The flash is attached to the volume buttons, mute switch and power button. If they are working then its just the flash which is faulty and the flex will need replacing. I hope this helps.
Leer másIts very tricky on the iPhone 4, but you need to slide the cables through the back of the phone at a 90 degree angle, otherwise they won’t be long enough to reach the connectors on the board.
Leer másI refurbish screens but it isn’t worth buying all the equipment if you’re only going to refurbish one screen as it costs thousands. There are other methods that you can use but they are DIY methods. For example to remove the glass you can use a heat gun and plastic to get under the glass and take it off. Then when installing the new glass, you’d use LOCA instead of OCA, then use an ultra violet light to cure the LOCA glue.
Leer másYes you will get a screen warning if the IC chip isn’t transferred over. Whether its a genuine screen or not you’ll still get the same message. I believe the message will be displayed on the home screen for 4 days, then 15 days in the settings, so be extra careful when refurbishing the original display.
Leer másI can’t see the housing affecting the signal, I think the wifi antenna itself may have got damaged when the incident happened.
Leer másNo they aren’t transferable.
Leer másYes you can test it without transferring them over, you’ll get a message saying “Face ID can’t be activated on this device” as soon as you install the face ID module and put the phone back together, the message will disappear.
Leer másPág. 1 de 6
Comentarios de guía
Try changing the screws around, I had this same issue and I`d just put the screws the wrong way around. As soon as I changed them back around, the vibrate motor worked perfectly and sounded normal again. If they are the wrong way around, the vibrator will work intermittently and make the entire phone vibrate.
Luke
@coopzzz360
From the UK, my passions are football & repairing/refurbishing Apple devices.
Votos
5
1