Saltar al contenido principal

Introducción

¿La pantalla de tu Pixel está rasgada o rota? Sigue esta guía para reemplazarla.

El panel de pantalla no reforzado del Pixel 3a es frágil. Si estás reutilizando la pantalla, asegúrate de prestar especial atención a las advertencias en el procedimiento de apertura.

  1. Toma nota de las dos juntas en el teléfono: Juntura de la pantalla: Esta juntura separa la pantalla del resto del teléfono. Es aquí donde deberías hacer palanca. Juntura del marco:  Esto es donde el marco de plástico se junta con la tapa trasera. Se sujeta en su lugar mediante tornillos. No hagas palanca en esta juntura.
    • Toma nota de las dos juntas en el teléfono:

    • Juntura de la pantalla: Esta juntura separa la pantalla del resto del teléfono. Es aquí donde deberías hacer palanca.

    • Juntura del marco: Esto es donde el marco de plástico se junta con la tapa trasera. Se sujeta en su lugar mediante tornillos. No hagas palanca en esta juntura.

    • Antes de empezar a hacer palanca, ten en cuenta las siguientes áreas de la pantalla:

    • Cable flexible de la pantalla: No hagas palanca más allá de lo indicado o correras el riesgo de dañar este cable.

    • Perímetro del adhesivo: Si haces palanca más allá del perímetro estrecho sin inclinar la púa, se dañará la pantalla .

    Power is off, but does the battery need to be disconnect to safely do this replacement?

    mplishka - Contestar

  2. Calienta un iOpener y aplícalo al borde derecho de la  pantalla durante un minuto
    • Calienta un iOpener y aplícalo al borde derecho de la pantalla durante un minuto

    • Puedes optar por omitir este paso ya que el adhesivo para pantallas de Pixel 3a no es muy fuerte. Calentarlo, sin embargo, disminuirá la posibilidad de agrietar la pantalla.

    I used a washcloth soaked with hot water and sealed in a plastic bag instead of the iOpener for this step, and it worked great.

    E. Dunham - Contestar

  3. Coloca una ventosa cerca del borde derecho de la pantalla. Tira de la ventosa con fuerza constante. Inserta la púa en  la grieta , no más de 1 mm.
    • Coloca una ventosa cerca del borde derecho de la pantalla.

    • Tira de la ventosa con fuerza constante.

    • Inserta la púa en la grieta , no más de 1 mm.

  4. Este paso muestra cómo insertar la púa sin dañar el panel OLED. Haz esto antes de cortar los borders largos del teléfono. Con la púa 1 mm dentro de la grieta, gira la púa hacia arriba hasta un ángulo pronunciado. En este ángulo, empuja cuidadosamente la púa en el espacio aproximadamente 6 mm. La púa debe deslizarse por debajo del panel OLED.
    • Este paso muestra cómo insertar la púa sin dañar el panel OLED. Haz esto antes de cortar los borders largos del teléfono.

    • Con la púa 1 mm dentro de la grieta, gira la púa hacia arriba hasta un ángulo pronunciado.

    • En este ángulo, empuja cuidadosamente la púa en el espacio aproximadamente 6 mm. La púa debe deslizarse por debajo del panel OLED.

    • Deténte si sientes que la punta de la púa golpea un borde. La púa puede estar presionando contra el borde del panel OLED. Inclina la púa e inténtalo de nuevo.

    If you don’t have picks, you can also use the corner of an old gift card, though it may be necessary to shave it a bit thinner with a knife so it fits the gap better.

    E. Dunham - Contestar

  5. Desliza la púa a lo largo del borde derecho, cortando el adhesivo. No insertes las púa más de 6 mm, ya que podrías dañar el cable flexible de la pantalla. Deja una púa en su lugar para que el adhesivo se vuelva a sellar.
    • Desliza la púa a lo largo del borde derecho, cortando el adhesivo.

    • No insertes las púa más de 6 mm, ya que podrías dañar el cable flexible de la pantalla.

    • Deja una púa en su lugar para que el adhesivo se vuelva a sellar.

    Don’t make my mistake and read ahead. 6mm may be too close for comfort! 8mm is definitely too far and caused me to damage. Also be sure to read the right manual! I have an XL and it notes 5mm.

    Miguel Higgins-Moy - Contestar

    Fortunately my old screen was beyond repair, But be super careful around the bottom I managed to sever the ribbon cable to the digitizer.

    Stephen Hammons - Contestar

    I broke my screen here. The adhesive in my case was quite strong on the top and bottom.

    Mario Flores - Contestar

    This is by far the hardest part of the entire replacement. I ruined my screen doing this, you might as well buy a new screen at the same time as you buy your battery. I just barely rubbed the edges of my screen and it turned the edge of my screen purple. This eventually migrated to the entire screen causing the whole thing to be purple/black.

    Ross Lancaster - Contestar

  6. Al cortar alrededor del borde inferior del teléfono, no insertes a la púa más de 6 mm. Desliza la púa por la esquina inferior derecha para cortar el adhesivo. Si la esquina se siente difícil de cortar, aplica un iOpener caliente a la esquina durante un minuto e inténtalo de nuevo.
    • Al cortar alrededor del borde inferior del teléfono, no insertes a la púa más de 6 mm.

    • Desliza la púa por la esquina inferior derecha para cortar el adhesivo.

    • Si la esquina se siente difícil de cortar, aplica un iOpener caliente a la esquina durante un minuto e inténtalo de nuevo.

    • Continúa cortando a lo largo del borde inferior del teléfono y a la vuelta de la esquina izquierda.

  7. Corta a través del borde izquierdo del teléfono, asegurándote de inclinar correctamente la púa debajo del panel OLED e insértela  no más de 6 mm. Para inclinar la púa debajo del panel OLED, inserta la punta de la púa no más de 1 mm, inclina la púa hacia arriba, y luego empuja lentamente la púa 6 mm. Para inclinar la púa debajo del panel OLED, inserta la punta de la púa no más de 1 mm, inclina la púa hacia arriba, y luego empuja lentamente la púa 6 mm.
    • Corta a través del borde izquierdo del teléfono, asegurándote de inclinar correctamente la púa debajo del panel OLED e insértela no más de 6 mm.

    • Para inclinar la púa debajo del panel OLED, inserta la punta de la púa no más de 1 mm, inclina la púa hacia arriba, y luego empuja lentamente la púa 6 mm.

  8. Corta a lo largo del borde superior mientras mantienes la púa no más de 8 mm adentro. Corta a lo largo del borde superior mientras mantienes la púa no más de 8 mm adentro. Corta a lo largo del borde superior mientras mantienes la púa no más de 8 mm adentro.
    • Corta a lo largo del borde superior mientras mantienes la púa no más de 8 mm adentro.

    There is a LOT more adhesive at the top than anywhere else on the phone! It’s like there’s 2 lines of adhesive, one along the edge of the case and one along the edge of the screen, and it’s filled in between them wherever the speaker camera aren’t. I needed to heat and pry several times to get the top loose. Fortunately, there’s little risk of hitting a cable near the top (look ahead to the step where you lift the screen off to see where all the cables go!)

    E. Dunham - Contestar

    I found that applying the iOpener across the top edge of the glass for about 30 seconds at this step helped soften the adhesive significantly. My front camera was replaced only a few months ago by uBreakiFix and the display adhesive subsequently let go on the entire right edge, bottom, and part of the left side shortly after the new front camera failed. Only the top was still securely stuck.

    Reid Solberg - Contestar

  9. Con todos los bordes cortados, abre con cuidado el borde derecho de la pantalla. No quites la pantalla. Sigue conectado al teléfono mediante un cable flexible cerca del borde izquierdo.
    • Con todos los bordes cortados, abre con cuidado el borde derecho de la pantalla.

    • No quites la pantalla. Sigue conectado al teléfono mediante un cable flexible cerca del borde izquierdo.

    • Utiliza una púa de apertura para cortar con cuidado cualquier resto de adhesivo.

  10. Con todos los adhesivos cortados, voltea el vidrio de la pantalla hacia abajo y colócalo en la parte superior del teléfono. El cable flexible de la pantalla  debe estar ligeramente arqueado. Con todos los adhesivos cortados, voltea el vidrio de la pantalla hacia abajo y colócalo en la parte superior del teléfono. El cable flexible de la pantalla  debe estar ligeramente arqueado. Con todos los adhesivos cortados, voltea el vidrio de la pantalla hacia abajo y colócalo en la parte superior del teléfono. El cable flexible de la pantalla  debe estar ligeramente arqueado.
    • Con todos los adhesivos cortados, voltea el vidrio de la pantalla hacia abajo y colócalo en la parte superior del teléfono. El cable flexible de la pantalla debe estar ligeramente arqueado.

    Hi, could you help me with one clarification?

    What does the small “metal patch” in the middle of the display ribbon do?

    Does it prevent the phone from starting while disconnected?

    Thank you for your time!

    oliver schirmer - Contestar

    Hi Oliver,

    I think the patch you’re referring to helps with either EM shielding or heat dissipation. It should not prevent the phone from starting.

    Arthur Shi -

  11. Despega cuidadosamente la cinta negra que cubre el soporte del conector de la pantalla. Si está en buenas condiciones, puedes reutilizar esta cinta durante el reensamblaje. De lo contrario, reemplázalo con un trozo de cinta adhesiva eléctrica. Retira los dos tornillos T3 de 4.4 mm de largo que fijan el soporte del conector de la pantalla.
    • Despega cuidadosamente la cinta negra que cubre el soporte del conector de la pantalla.

    • Si está en buenas condiciones, puedes reutilizar esta cinta durante el reensamblaje. De lo contrario, reemplázalo con un trozo de cinta adhesiva eléctrica.

    • Retira los dos tornillos T3 de 4.4 mm de largo que fijan el soporte del conector de la pantalla.

    • Retira el soporte del conector de la pantalla.

    This may be a silly question but how are you able to tell whether the tape is in good condition? Is it based off of how sticky it is after you remove it?

    Sylvia - Contestar

    That is a fair question! If the tape is in one piece and is relatively sticky, it can probably be used again.

    Arthur Shi -

    Oops! I forgot to put any tape back. Does this tape have a critical purpose, in other words should I go to the trouble to pry the screen back off and tape it?

    elyze - Contestar

    The tape does not serve a critical purpose. If you have already re-sealed your phone, I wouldn’t worry about it.

    Arthur Shi -

    Les vis sont des T4 et non des T3

    Gaëtan PERRIER - Contestar

    Bonjour Gaëtan ! Merci pour la remarque. En fait, il y a toujours une certaine tolérance entre le tournevis et la tête de vis. Donc il se peut que la taille supérieure ou inférieure soit plus “confortable” au cas par cas. Bonne réparation !

    Claire Miesch -

    Bonjour,

    Pouvez-vous me conseiller un bon kit de réparation pour mon Google Pixel 3A?

    J'ai peur de me faire arnaquer en achetant un mauvais écran de basse qualité .

    mailsecoursd - Contestar

  12. Usa la punta de un spudger para entrometerse y desconectar el cable flexible de la pantalla. Cuando desconectes conectores como estos, ten cuidado de no desalojar los pequeños componentes montados en la superficie que rodean el zócalo.
    • Usa la punta de un spudger para entrometerse y desconectar el cable flexible de la pantalla.

    • Cuando desconectes conectores como estos, ten cuidado de no desalojar los pequeños componentes montados en la superficie que rodean el zócalo.

    • Para volver a colocar los conectores de presión como éste, alinea y presiona con cuidado en un lado hasta que encaje en su lugar, luego repite en el otro lado. No presiones hacia abajo en el centro. Si el conector está desalineado, los pines pueden doblarse, causando daños permanentes.

    I had accidentally pressed the power button and the phone was on when connecting the new screen and that broke the board! So make sure the phone is off.

    Diako Mardanbegi - Contestar

  13. Remueve la pantalla. Con atención compara tu pantalla de reemplazo con tu pieza original. Podrías necesitar transferir componentes adicionales (como la malla del auricular) a la nueva pieza. Para volver a instalar la pantalla:
    • Remueve la pantalla.

    • Con atención compara tu pantalla de reemplazo con tu pieza original. Podrías necesitar transferir componentes adicionales (como la malla del auricular) a la nueva pieza.

    • Para volver a instalar la pantalla:

    • Sigue esta guía si estás usando adhesivos personalizados.

    • Si estás usando cinta de doble cara (como la cinta de marca Tesa), usa esta guía

    There is a blue plastic tape covering the digitizer and when I try to take it off it rips out something more than just the tape I think it’s pulling the magnet too

    Darien Suarez - Contestar

    i had a little plastic piece around the camera (seems to just be a spacer) that i moved to the new screen. had to pry it up with a pick cuz it was stuck down good.

    elyze - Contestar

    actually to clarify- i didn’t move the little camera spacer to the new screen- i placed it around the camera on the phone, where there was a little indent for it, and stuck it down with a bit of tesa strip, then applied more tesa strips around the edge of the phone before finally reconnecting and replacing the screen. the little plastic bit i encountered needs to be precisely placed around the camera so would not be a good idea to just stick it to the screen when reinstalling!

    elyze -

    Thanks team! I was able to replace my broken screen with no issues!

    Instead of cutout adhesives or tesa tape, I used B-7000. Painless.

    Appreciate the screen and instructions!

    Jessica Hale - Contestar

    Bonjour,

    Pouvez-vous me conseiller un bon kit de réparation pour mon Google Pixel 3A?

    J'ai peur de me faire arnaquer en achetant un mauvais écran de basse qualité .

    Hello . Can you advice me a site where i Can buy a quality screen replacement pack for my Google Pixel 3A?

    There's a lot of rip off on internet and id like to get a good pack and a quality screen .

    Bichette Laterreur - Contestar

    Hello! We currently sell a replacement screen. However, I’m not sure if it is available yet internationally.

    Arthur Shi -

    I have a quick question, so I haven’t done anything yet because I only just ordered my repair kit, but is it possible to replace the battery without having to replace the display ?

    Braeden - Contestar

    Hi Braeden!

    Yes, it is definitely possible to replace the battery without replacing the display. With that said, the initial entry steps can be pretty tricky. Before you begin, look very closely over the display to see if you can see any micro-fractures. If you see any, you will most likely crack the screen when you try to remove it. Take your time and apply a heated iOpener often. Good luck!

    Arthur Shi -

    I forgot to order the tape when getting my replacement USB port, so I ended up putting the screen back on without any tape and using regular clear tape on the outside of the phone to keep the screen from falling off. It’s less waterproof, but it’ll do the job until the right part arrives.

    E. Dunham - Contestar

    Speaker mesh appeared to already be in place on my replacement screen, so I did not transfer this over from my old screen. That was a huge mistake, sounds were garbled above about 30% volume. Make sure you do this part!

    Evan Heisman - Contestar

Conclusión

Si tu dispositivo Pixel no se enciende después de sustituir la pantalla, existe la posibilidad de que el teléfono se encendiese silenciosamente al reconectar la batería. Mantén apretado el botón de encendido hasta que el teléfono vibre. Después de esto, reconecta la pantalla e inténtalo de nuevo.

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

Lleva tus desechos electrónicos a un centro de reciclaje certificado.

¿La reparación no salió como planificaste? Consulta nuestra comunidad de respuestas de Google Pixel 3a para ayudarte en la resolución de los problemas que tengas.

44 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Arthur Shi

Miembro Desde 03/01/18

173,389 Reputación

428 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

140 Miembros

17,046 Guías creadas

42 comentarios

Olá! Vocês sabem onde posso achar essa tela pra comprar? Obrigada!

annebfsl - Contestar

Any word on the replacement screens?

Ernest Zamelczyk - Contestar

We should have replacement screens in stock in the next month or two! Thanks for your patience.

Arthur Shi -

I’ve cracked not only my LCD screen, but also the frame seam (shown with orange line in step 1 above). Will you be posting a guide to replace this also, or could you incorporate into this guide? Also interested if this will be available as a spare? Thanks.

Mark Waring - Contestar

Hi Mark,

I’m sorry to hear that! The frame seam is part of the plastic midframe—you would need to replace the midframe to replace the cracked seam. Instructions on how to do so can be found in this guide.

Because the Pixel 3a is a relatively new phone, replacement parts are harder to find for it. You can always buy a broken phone and transfer the part over, or use some adhesive to hold the cracked frame seam in place.

Arthur Shi -

Can the digitizer be separated from the screen easily? It’d be a lot cheaper for me to replace the scratched glass screen and reuse digitizer. Anyone try this? Thanks!

timkeenan02 - Contestar

The OLED display is fused to the front glass, so it will be very difficult to separate the digitizer without killing the fragile OLED panel. If it was a LCD panel, you would have a better chance de-laminating the digitizer.

Arthur Shi -

Two comments: when I bought the replacement digitizer on EBay, since the seller was packing in tools (which actually weren’t the right size) I assumed that the glue would be included, as well as speaker mesh; thankfully I didn’t trash the old speaker mesh, and the instructions pointed out that I may have to reuse it (thanks Alex and Arthur!), but on glue I got screwed big time, since I removed the old glue as the instructions suggested, before realizing I don’t have any replacement. So now my phone is sitting open on a desk while I’m waiting for the glue to arrive who knows when. You mention the “Tesa” adhesive tape, but don’t really specify which particular width did you use (which width, how much of it, when and where to apply it, etc.) which would be useful.

My second comment is that this particular guide seems to assume that the screen that’s being removed is in one piece; I imagine most people trying to do this actually have a smashed glass and could use some guidance how to deal with *that*…

Bob Jones - Contestar

Also, some guidance what to do with the adhesive tape would be useful (apply to the frame first, or apply to the digitizer first, etc.; the more specific, the better)…

Bob Jones -

Hi Bob,

Your eBay experience is definitely not an exception! eBay kits usually contain inferior or incorrect tools. Be careful not to strip any screws!

It looks like our custom adhesive for this phone is temporarily out of stock. The Tesa adhesive card is a great alternative, as it has many widths for different applications. You can find instructions for the adhesive card here.

If you are working with custom cut adhesives, the general rule of thumb is to peel the clear backing first. Figure out which component the exposed adhesive sticks onto, and apply it there. Next, peel the colored liner to expose the remaining adhesive.

Arthur Shi -

Are the screens the original AMOLED from the google production? Are they inferior, on par or superiror to OEM parts?

Mike - Contestar

Still no replacement screens?

(edit: I see now they are available in the US, but what about Europe?)

Paul - Contestar

I replaced the display and when it is turned on for the first time, everything works, but when it goes on standby when I switch it on again the touchscreen doesn't work anymore.

rensan - Contestar

Thanks, this worked a charm! The only problems I had were cleaning all the glue off everything and reattaching the screen connector - it’s a bit tricky because the cable has to bend to fit into the recessed area which makes it hard to align the connector.

Also, I couldn’t wait for a pre-made adhesive to arrive so I went to Officeworks and bought some 3mm double-sided tape called X-Press It (the high-tack version). This seems to have worked very well (but time will tell!)

J Wilson - Contestar

Replaced screen with one on there website. Screen is kinda late on response. Also sometimes gets stuck where I can’t click on anything and have to restart the phone. Is this a problem with the screen or the phone?

Joshua - Contestar

Hi Joshua,

That may be a screen/digitizer issue. I would suggest carefully re-seating the display connector and checking to see if there’s any debris. Otherwise, please contact our customer service and we’ll get things sorted out for you!

Arthur Shi -

Buongiorno, ho sostituito lo schermo del mio pixel 3a ed i colori non mi convincono, sembrano diversi. Lo schermo è stato acquistato qui sul sito, devo presumere che si sia stortato qualche pin del connettore o è proprio lo schermo che ha una tonalità dei colori diversa?

Jo Ma - Contestar

Ciao!

Ci dispiace che il telefono non funzioni come prima. Magari puoi provare di spegnere e riaccendere il telefono e/o di fare un reset.

Se questo non risolve il problema, rivolgiti a nostro servizio di assistenza: support@ifixit.com (in caso di un acquisto sul sito americano) indicando il tuo numero di ordine. Sarà un piacere aiutarti!

Cordiali saluti,

Claire

Claire Miesch -

can I confirm that this screen replacement is also an LCD replacement? I dropped my phone and cracked the glass but also the LCD is now not working (all black). Will this replacement fix both of those problems?

James - Contestar

Hi James!

Yes, the part listed in the “parts required” section is a screen replacement, which includes the top glass and the OLED panel underneath it. The Pixel 3a uses an OLED panel instead of a LCD. If nothing else broke on your phone, then doing this repair should fix your display issues.

While the repair is not as difficult as some of the other Pixel phones, you should read through the guide to get a sense of the overall procedure.

Good luck on your repairs!

Arthur Shi -

excellent guide, thank you arthur! this was so much easier than my pixel 3 and dare i say.. just plain easy!! love the 3a for repairability!!

elyze - Contestar

i came back to say- as easy as this guide and repair are to follow, i feel like i may have a bad part?

the screen stopped working at first and seemed to have something to do with the fit of the screen. it was coming up a bit on the top right and not seated fully. so i pried it up again, reseated the cable, and resealed the edges more carefully. since then it works better but seems like it stops responding correctly frequently. rebooting generally helps. but after working fine for a while.. the touch function will suddenly and quickly deteriorate until it just doesn’t work altogether, and then i have to reboot.

each time i connected the digitizer cable i tested the device before sealing it with adhesive. i don’t really understand what could cause the issue because it works perfectly for a while before randomly petering out.

elyze -

That is a strange occurrence that shouldn’t be happening. If you bought the part from iFixit, please contact our customer support!

Arthur Shi -

I’m curious if it’s possible to remove only the top glass from the OLED? My crack seems to be superficial, the digitizer works in/around/through the cracks (dragging/clicking items), and I can see under the cracks that the display is fine.

They sell replacement kits for just the front glass, but I’ve also heard that they’re difficult to take apart. Any advice?

Alex Markovic - Contestar

Hi Alex,

Replacing the glass only is doable, but involved and requires specialty tools. The fragile OLED panel is bonded to the glass. You need a jig to hold the phone in place while you thread a thin wire between the glass and the OLED panel to slice through the LOCA. Once you separated the glass, you’d need to clean off the OLED panel and apply new LOCA.

The front glass only parts are usually sold to refurbishers, who are well-practiced in doing this kind of repair. It is definitely a skill you can learn and be good at with practice!

Arthur Shi -

Hi,

My screen stays entirely black, after falling down (but it didnt hit anything, i was wearing earphones). It had however cracks from a previous fall. Do you think replacing the screen will be the sollution or is there another problem?

with kind regards

laurence trachez

laurence_trachez - Contestar

Hi Laurence,

This is hard to say. If you try to power on your phone, does it vibrate? If it does, then a replacement screen will probably fix the problem.

Arthur Shi -

The explanation to replace the screen are well done. The screen itself flashes everytime I turn on the phone. The biggest problem is when I call someone. The screen goes black and I can’t hang up or do a selection. This is a problem.

frinfret - Contestar

Mine have the same “flash” problem. Any solution?

Gin Mor -

I have complete the repair and everything boots up, display looks great but I have no digitzier/touch input. Faulty replacement screen? I have verified the screen connection and tried reboots and reconnects with no success. Any tips?

James Jenkins - Contestar

Hi, I have cracked only the glass, not the screen. I have seen numerous comments like this one: “A screen on its own is impossible to use on a Pixel 3a since the original screen is permanently attached to the LCD. Simply put, the only way to replace a screen on a Pixel 3a is to purchase a replacement screen/LCD combo.”

So can I order just the glass and replace the glass, and not glass and lcd combo?

Kristian Karaneshev - Contestar

Hi Kristian,

Without specialty tools, it would be very difficult to replace the glass without damaging the fragile display panel. The OLED display panel is bonded to the top glass with optically clear adhesive, so you’d need to slice through that without marring the panel. Refurbishment/repair companies use special jigs to accomplish this task.

Some devices use LCD panels that are not bonded to the top glass. In that case, it is easy to replace the glass by itself.

Arthur Shi -

My Pixel 3a screen has developed a “washed out” look with a green tint - everything else works fine. Is it possibly just a loose cable that can be fixed by opening per your instructions and firming up the connections? Thx!

Rob Gutman - Contestar

Hi Rob,

The display cable may be loose, but it could be something else. Opening up Pixel phones always poses a risk of further damaging the fragile display. Has the phone been water damaged/immersed before?

Arthur Shi -

Never wet or immersed, just the normal banging around of everyday use.

Rob Gutman -

Hmm…considering that the display connector is secured by a bracket, I think it’s unlikely that a loose connector is the issue. It may be a broken passive component somewhere in the display driver circuitry.

Arthur Shi -

Sounds like you're suggesting a screen replacement. Do I have that right? Ifixit parts and directions were spot on last time I replaced a screen! Thx

Rob Gutman - Contestar

Hello. Do you ship to the Philippines?

Lloyd Dotimas - Contestar

Hi Lloyd,

We currently do not ship to the Philippines, but that may change in the future. Please check this page occasionally for updated shipping locations!

Arthur Shi -

I attempted this repair but now the phone will not turn on at all. All I see is a faint blue line at the bottom of the LCD Screen. This is not my first time repairing phones and I followed the directions precisely. I don’t know what went wrong.

Greg Fine - Contestar

Bonjour, je souhaite changer l’écran de mon Google PIXEL 3A et j’hésite sur la pièce à commander : commander une vitre avant est-il suffisant ou faut-il le bloc complet LCD ? Ce n’est pas les mêmes prix. Ci-dessous le lien vers la pièce que je pensais commander, qu’en pensez-vous ? Merci ! https://www.cdiscount.com/telephonie/acc...

Rose TOUZET - Contestar

Hello!

The Pixel 3a uses an OLED display instead of a LCD. The OLED is very fragile and is glued onto the front glass (which is the part you linked). You need special equipment in order to separate the front glass without damaging the OLED display. If you are repairing the phone yourself, you should buy the complete screen assembly.

Le Pixel 3a utilise un écran OLED au lieu d'un écran LCD. L'OLED est très fragile et est collée sur la vitre avant (qui est la partie que vous avez liée). Vous avez besoin d'un équipement spécial afin de séparer la vitre avant sans endommager l'écran OLED. Si vous réparez le téléphone vous-même, vous devez acheter l'ensemble écran complet.

Arthur Shi -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 75

Ultimos 7 días: 501

Ultimos 30 días: 2,483

Todo El Tiempo: 101,650