Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

  1. Turn  the camera so the back of it is facing you.
    • Turn the camera so the back of it is facing you.

    • Pull the LCD screen towards you in order to open it,

  2. Unscrew the two 3 mm screws shown on the left side of the LCD screen panel  using a Phillips screwdriver. Unscrew the two 3 mm screws shown on the left side of the LCD screen panel  using a Phillips screwdriver.
    • Unscrew the two 3 mm screws shown on the left side of the LCD screen panel using a Phillips screwdriver.

  3. Unscrew the two 3 mm screws shown on the right side of the LCD screen panel. Unscrew the two 3 mm screws shown on the right side of the LCD screen panel. Unscrew the two 3 mm screws shown on the right side of the LCD screen panel.
    • Unscrew the two 3 mm screws shown on the right side of the LCD screen panel.

  4. Using the plastic opening tool, remove the rear case of the front LCD cover. Using the plastic opening tool, remove the rear case of the front LCD cover.
    • Using the plastic opening tool, remove the rear case of the front LCD cover.

  5. SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

    SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación
  6. Pull off the back panel of the LCD screen and the plastic wire protector. Then replace the back panel.
    • Pull off the back panel of the LCD screen and the plastic wire protector. Then replace the back panel.

  7. Unscrew the 2mm screw on the outer edge of the panel
    • Unscrew the 2mm screw on the outer edge of the panel

  8. Unscrew the 3mm screw on the inner edge of the panel. This is easily done by rotating the screen to be perpendicular to the body of the camera, but be careful not to damage the wires or the circuit board. The panel will fall right off
    • Unscrew the 3mm screw on the inner edge of the panel. This is easily done by rotating the screen to be perpendicular to the body of the camera, but be careful not to damage the wires or the circuit board.

    • The panel will fall right off

  9. Use spudger to remove the gold ribbon wire This is easily done by lifting up the small black lock that holds the ribbon wire in place
    • Use spudger to remove the gold ribbon wire

    • This is easily done by lifting up the small black lock that holds the ribbon wire in place

  10. Use tweezers to remove the second ribbon wire
    • Use tweezers to remove the second ribbon wire

    • This is best done by grasping at the base and pulling straight away from the circuit board

  11. Lift the LCD screen out of the metal casing. This is especially easy if you run the plastic opener along the bottom of the case
    • Lift the LCD screen out of the metal casing.

    • This is especially easy if you run the plastic opener along the bottom of the case

    • When the screen pops out, replace it with the new one.

  12. Place the wires back on the circut board
    • Place the wires back on the circut board

    • The large one can be replaced by placing the wire gently in the slot and then pushing the lock into place

    • The smaller wire should be fed back into the board using tweezers to prevent bending at the edge.

    • To finish, follow the previous steps in reverse order to put everything back where it belongs

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Ellis DeVoe

Miembro Desde 14/04/15

574 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 5-12, Maness Spring 2015 Miembro de Cal Poly, Team 5-12, Maness Spring 2015

CPSU-MANESS-S15S5G12

4 Miembros

5 Guías creadas

Great instructions. Took me less time than estimated. Thanks

frankypianoforte - Contestar

Thank you. Very clear instructions.

Barbara Allred - Contestar

Hi, I just bought a display lcd screen. but it has only one ribbon, not have the little tiny one. What should I do?

Sadia Afrin - Contestar

Was any body able to find the replacement screen with 2 ribbon cables for the Canon SX30 IS having back light?

If so please share I’m in need of one for my camera.

Thanks

lukebuser - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 3

Ultimos 30 días: 18

Todo El Tiempo: 1,478