Canon PowerShot S50 LCD Screen Replacement

Jacob y 7 otros contribuidores

Última actualización: July 30, 2014

Sin estimación

Moderado

Guía Destacada

Introducción

Ir al paso 1

The 1.8 inch LCD Screen is the main method of interaction between the user and the camera. If the screen malfunctions, it may be useful to replace it. New screens can be bought here

Qué necesitas

Herramientas

iFixit gana una comisión si finalizas una compra usando estos enlaces.

Paso 1 Battery

Canon PowerShot S50 LCD Screen Replacement, Battery: paso 1, imagen 1 de 2

Canon PowerShot S50 LCD Screen Replacement, Battery: paso 1, imagen 2 de 2

Place camera LCD side up and press up on the battery door.
Let it swing open until you can see the battery inside.

Editar

Paso 2

Press down on the orange plastic.
This will gently eject the battery from its compartment.

Editar

Paso 3

Holding the edges, slide out the battery.

Editar

Paso 4 Front Panel/Battery Door

Canon PowerShot S50 LCD Screen Replacement, Front Panel/Battery Door: paso 4, imagen 1 de 1

Look at the camera from the side with the lanyard and 4 screws.
Remove the two 3.4 mm screws on the metallic colored part.

Editar

Paso 5

Remove the 3mm screw on the top left.
NOTE: When reassembling, it is helpful to put the top screw back in before placing the front cover back on the camera.
Now remove the 5.3mm screw on the bottom.

Editar

Paso 6

Place the camera LCD side down.
Remove the two 5.3mm screws by the battery door.

Editar

Paso 7

Remove the four 3.4mm screws on the bottom of the camera around the tripod mount.
Make sure to keep these screws separate from the previous 5.3 mm screws.

Editar

Paso 8

Stand the camera back up.
Remove the two 3.6mm screws on the side with the A/V Out port.

Editar

Paso 9

Lift open the rubber flap covering the A/V Out port.
Remove the 3.4mm screw in the center.
During reassembly, put the A/V out rubber door on before replacing the front panel of the camera

Editar

Paso 10

Use a spudger and gently open up the front panel of the camera.
A thin plastic ribbon will stay connected by a brown piece to front panel of the camera.

Editar

Paso 11

There will be a brown plastic piece keeping the thin plastic ribbon in place.
Use the spudger to pull out the brown plastic piece attached to the orange plastic.

Editar

Paso 12

Herramienta utilizada en este paso:

Tweezers

$4.99

Añadir a la cesta

Use a pair of tweezers and remove the metal piece inside the camera.

Editar

Paso 13

Remove the battery door
NOTE: Putting this back on requires aligning the spring on the back of the door with the hole on the camera

Editar

Paso 14 Right Motherboard

Canon PowerShot S50 LCD Screen Replacement, Right Motherboard: paso 14, imagen 1 de 1

Disconnect the two plastic ribbons on the lower half of the right motherboard.
NOTE: You will have to lift up the brown plastic piece in order to pull out the second ribbon wire.

Editar

Paso 15

Remove the two 3.4mm screws on the right motherboard.

Editar

Paso 16

Disconnect the two wired plugs below the flash.

Editar

Paso 17

Disconnect the wired plug at the bottom of the right motherboard.

Editar

Paso 18

Herramienta utilizada en este paso:

Tweezers

$4.99

Añadir a la cesta

Use a pair of tweezers to pull the right motherboard away from the main body of the camera.

Editar

Paso 19 Outer Casing

Canon PowerShot S50 LCD Screen Replacement, Outer Casing: paso 19, imagen 1 de 1

Using a spudger, gently separate the back panel from the rest of the camera and remove it.

Editar

Paso 20 LCD Screen

Canon PowerShot S50 LCD Screen Replacement, LCD Screen: paso 20, imagen 1 de 1

Remove the 2.6mm screw on the bottom of the camera located directly under the LCD screen.
This screw should be holding two pieces of orange film down.
When replacing this screw, make sure that the orange film is secure below it before screwing it in.