Hello Matthew Alexander Is the hard drive damaged? Or do you need the information stored on the desktop and partition C?What do you want to recover?Did you create the partition D on the hard drive?

Hello Janell Sampson After taking a backup, you can restore it with the help of a backup file. 1- laptops often have a recovery program of their own. Check if this backup is already stored on your computer hard drive by the manufacturer's utility. To do this, go to the path below (Windows XP or Vista or 7 or 10) Computer>Control panel>Administrative Tools>Computer Management>In Computer Management (Local) select “Disk Management”> Now be careful, do you see a hidden partition? (Except the partition with a size of 100 MB MBR=Master Boot Record which is located before the C partition ) 2-If you see the backup file that is hidden in this list, go to the web page of the computer manufacturer and in the relevant downloads section - download and install your laptop recovery program and perform the recovery operation with it. 3-If in section1 you did not see the backup file, it means you can not recover it by your computer program. You now have two options: either make a backup file with the help of Windows or...

Hello Racquel Miller Are you able to update the Android (operating system )?You will need to re-enter your Gmail account

Hello Shauna b You probably have not used your printer for a long time or it is in a relatively warm place and the printer head is closed by dried ink. Use good quality ink and clean the head several times through the device menu several times and repeat it. Sometimes you have to replace the printer head. Inkjet printers may not be right for you, and you may want to get a laser printer. Because inkjet printers need to work regularly to keep the nozzles and heads clean .

Hello Selcuksancak 1- Carefully remove all dust on the fan blades . 2- Use a- contact cleaner spray- (greasy). Connect the spray guide channel and carefully spray a small amount on the fan motor shaft(Bearings). If the sound is removed, use a very small amount of lubricating oil rubbed on the tip of the screwdriver to do a thorough lubrication. 3-Make sure you replace the fan correctly Update (09/05/2021): Hello Dan Thanks for the answer. Yes . Any oil collects dust. Light oils evaporate faster and have a shorter effect . The blades must be carefully cleaned after applying the oil .However, the new fan in such a quality computer should not make noise and the problem is probably the way to replace the fan - as you mentioned. *The oilless bearings(Oilless Bearing | Always Self-lubricating ) themselves also contain solid oil, which friction causes them to heat up and the heat causes them to liquefy and then this liquid oil lubricates the shaft during operation, all of this happens in a closed chamber, so...

Hello John 1-Reinstall the headset driver. Make sure you are using the latest driver version. *Recently, if you have installed another audio driver, uninstall it . *Download the suitable driver from the product manufacturer's site or use programs such as “Driver Easy” to download the driver. 2-Control Panel>Sound>Playback tab>select this device (If the headset does not have a driver, select”Speakers”) now connect a desktop speaker and check the sound quality. 3-Make sure Windows(OS) does not have a sound problem . 4-Also check for hardware issues: Make sure that the USB port on the computer supplies power to the headset properly. Use an Android phone charger to check. Check cables and plugs as well.

Hello Ruduan Of course, by applying the Grayscale command, you usually get a black and white image on the screen(RGB Mode) and 8 bits(In each of the 4 color channels in CMYK mode) so when printing(even with Grayscale command in CMYK mode), the printer still uses 4 colors to produce it. I mean black and white printing in such a way that the printer does not use any of the three colors of cyan, magenta and yellow when printing . If you are good at working with Photoshop, you must first open your image in Photoshop. There are commands to make the image black and white when printed in that program. So if you mean what I said and if you are a little good at working with Photoshop, I can write the instructions for you in Photoshop in the next answer.

Reset the Network Settings to the Factory Settings ————————————————————- You can use your machine's WiFi button to reset the print server to its default factory settings. This resets all information, such as the password and IP address. (1) You can also reset the print server to its factory settings using BRAdmin Light, BRAdmin Professional 3, or Web Based Management. (2) Make sure the power cord is plugged in, the top cover is closed and the machine is turned off. (3) While holding down the Power button , open and close the top cover. (4) Release Power button . Make sure that all the LEDs turn off. (5) Press Power button six times. The machine will restart.

Hello Christopher 1-Open the top tray from the back and the bottom tray from the bottom . look at the machine warnings and remove the jammed papers from both trays. Usually a graphic icon appears on the display to guide you.follow it. read the manual of the device for more help as well. 2-I have a similar model of this printer, but a more advanced one. The mechanism of the two seems to be similar. I had the same problem. In the sub printer section where the paper is lifted from the bottom tray, there is a small tab system that is usually dirty and greasy. Wash it with a suitable solution and be careful not to touch any other part by hand .Normal alcohol is sufficient for washing with cotton. Do nothing to damage the system(important). Also this set is very sensitive to dust and you need to get a cover and put it on the machine. You may need to repeat this operation almost every9 months. Especially if you don’t use the printer for a while. 3-If you haven't used the printer for a long time, always remove the...

1-A multimeter or voltmeter is usually used to test the charger's health. It is not difficult to work with and you can buy a good model of it . 2-If the battery is not used for a long time and does not recharge, this can lead to such a problem. The right way to start is to check the charger first. If you haven't used the battery for a long time (this time may vary by type and quality and can range from four months to a year and a half or more), the battery may be damaged. Sometimes, using higher amps chargers(not voltage) than the original charger can cause a shock to the battery and return it to its normal cycle( not always). First make sure that the charger is not damaged then check the battery. Batteries like this are designed specifically for a device and are not conventional batteries (such as AA type) ,so should be tested with their device or with similar devices because the purpose is to charge them with their charger in the related devices. 3-In case you want to keep the battery unused for a long...