iPad Mini CDMA Logic Board Assembly Replacement

Walter Galan y 3 otros contribuidores

Última actualización: August 15, 2024

Sin estimación

Moderado

Sólo Prerrequisito

Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Introducción

Ir al paso 1

Prereq for disconnecting all connectors from logic board.

Qué necesitas

Herramientas

Paso 1 Logic Board Assembly

iPad Mini CDMA Logic Board Assembly Replacement, Logic Board Assembly: paso 1, imagen 1 de 2

iPad Mini CDMA Logic Board Assembly Replacement, Logic Board Assembly: paso 1, imagen 2 de 2

Herramienta utilizada en este paso:

Tweezers

$4.99

Añadir a la cesta

Use tweezers to peel up and remove the small piece of tape covering the front-facing camera cable connector.

Traducir

Paso 2

The front-facing camera cable connector is secured with pieces of tape that wrap up around the sides of the cable and are fastened to two small metal plates.
Use a plastic opening tool to gently pry the upper metal plate up from the front-facing camera cable connector.
Being careful not to break the plate or the tape attached to it, pry it up and fold it away from the front-facing camera cable connector.

Traducir

Paso 3

Gently pry the second (lower) metal plate up from the front-facing camera cable connector.
Again, carefully pry the plate up and away from the front-facing camera cable connector.

Traducir

Paso 4

Use a plastic opening tool to pry the front-facing camera cable's connector up from its socket on the logic board.

Traducir

Paso 5

Gently fold the front-facing camera cable up and out of the way of the logic board.

Traducir

Paso 6

Use tweezers to peel up and remove the small piece of tape covering the headphone jack cable connector.

Traducir

Paso 7

Use a plastic opening tool to gently pry the lower metal plate up from the headphone jack cable connector.
Being careful not to break the plate or the tape attached to it, pry it up and fold it away from the headphone jack cable connector.

Traducir

Paso 8

Pry the second (top) metal plate up from the front-facing camera cable connector.
Again, carefully pry the plate up and away from the headphone jack cable connector.

Traducir

Paso 9

Use a plastic opening tool to pry the headphone jack cable's connector up out of its socket on the logic board.

Traducir

Paso 10

Gently bend the headphone jack cable back, away from the logic board.

Traducir

Paso 11

Use a plastic opening tool to pry the top left antenna cable up from its socket on the logic board.

Traducir

Paso 12

Remove the following three screws securing the top right antenna to the rear case:
Two 1.3 mm #00 Phillips screws from the side of the antenna's socket.
One 1.8 mm #00 Phillips screw.

Traducir

Paso 13

iPad Mini CDMA Logic Board Assembly Replacement: paso 13, imagen 3 de 3

Disconnect the top right antenna's coaxial cable from the logic board with a plastic opening tool.
Gently bend the cable and screw tab up out of the way of the logic board.

Traducir

Paso 14

Use a plastic opening tool to pry the rear-facing camera cable up from its socket on the logic board.

Traducir

Paso 15

Pry the top right antenna's ribbon cable up from its socket on the logic board with a plastic opening tool.

Traducir

Paso 16

Use tweezers to peel up and remove the small piece of tape covering the button ribbon cable ZIF connector.

Traducir

Paso 17

Use the tip of a spudger to lift up the tab on the button ribbon cable ZIF connector.

Traducir

Paso 18

Use tweezers to pull the button ribbon cable straight out of its ZIF socket on the logic board.

Traducir

Paso 19

iPad Mini CDMA Logic Board Assembly Replacement: paso 19, imagen 3 de 3

Gently peel back the wide piece of tape covering the top of the right speaker.

Traducir

Paso 20

iPad Mini CDMA Logic Board Assembly Replacement: paso 20, imagen 3 de 3

Continue peeling the tape, and remove it from the iPad.

Traducir

Paso 21

iPad Mini CDMA Logic Board Assembly Replacement: paso 21, imagen 3 de 3

Use the flat end of a spudger to disconnect the two bottom antenna cable connectors from their sockets on the logic board.

Traducir

Paso 22

Use the tip of a spudger to peel back the small piece of tape covering both antenna cables on the bottom right side of the iPad.
Leave the lower part of the tape stuck to the back of the rear case to aid in reassembly.

Traducir

Paso 23

With the tip of a spudger, peel up the larger piece of tape covering both antenna cables near the bottom of the rear case.
Do not try to remove this piece of tape; it is wrapped around the top antenna cable.

Traducir

Paso 24

iPad Mini CDMA Logic Board Assembly Replacement: paso 24, imagen 3 de 3

Use the tip of a spudger to pry the small metal retaining clip off the left antenna cable, then de-route the cable from the clip.

Traducir

Paso 25

De-route the antenna cable from the corner of the iPad.

Traducir

Paso 26

Use the tip of a spudger to remove the small piece of tape securing the antenna cable in the bottom right corner of the iPad.

Traducir

Paso 27

Peel the cable back from the corner of the iPad.

Traducir

Paso 28

iPad Mini CDMA Logic Board Assembly Replacement: paso 28, imagen 3 de 3

Use the tip of a spudger to pry the antenna cable tape up from the rear case of the iPad.
Gently pull the antenna cable out of the way as you work along the piece of tape, to keep it from resealing.

Traducir