Introducción
Usa esta guía para reemplazar una batería gastada o agotada en tu Apple Watch Series 6.
Esta guía muestra el procedimiento en la versión celular/LTE del reloj. pero la versión GPS es similar.
Nota: el procedimiento de reemplazo de la batería para el Apple Watch Serie 6 de 40 mm difiere ligeramente de la versión de 44 mm. Esta guía muestra cómo reemplazar la batería para ambos tamaños.
Antes de comenzar, asegúrate de tener la batería de repuesto adecuada para tu reloj.
Si tu batería está hinchada, toma las precauciones adecuadas. Por tu seguridad, descarga tu batería por debajo del 25% antes de desarmar tu reloj. Esto reduce el riesgo de un evento térmico peligroso si la batería se daña accidentalmente durante la reparación.
Necesitarás adhesivo de reemplazo para volver a colocar los componentes cuando vuelvas a ensamblar el dispositivo.
Qué necesitas
-
-
Dado que el espacio entre la pantalla y el cuerpo del reloj es muy fino, se necesita una cuchilla afilada para separar ambos. Lee atentamente las siguientes advertencias antes de proceder.
-
-
-
Prepara un iOpener (o usa un secador de pelo o una pistola de calor) y calienta la esfera del reloj para aflojar el adhesivo de la pantalla.
-
Deja el iOpener en el reloj durante al menos dos minutos para calentar completamente la pantalla y ablandar el adhesivo que la sujeta a la caja.
-
-
-
Coloca el filo de una cuchilla curva en el fino hueco que hay entre la pantalla y la carcasa exterior. Comienza por el lado corto de la pantalla, el más alejado de la corona digital.
-
Presiona firmemente hacia abajo en el espacio.
-
Una vez insertada, inclina la cuchilla para abrir ligeramente la pantalla.
-
-
-
-
Levanta la pantalla y tira de ella con cuidado hacia la corona del reloj.
-
Abre la pantalla hacia arriba.
When I opened my watch I saw two layers of adhesive or are they gaskets? I broke one accidentally but not sure if I should keep the undamaged one in there? Or should both side be totally bare and the adhesive itself is also the seal?
Also I think I damaged my battery when prying it up since it won’t hold a charge now. I bought a replacement battery and will try that but is there anything else it could be?
Be very careful here... My display cable broke before achieving the angle they show in the last pick above. You may well want to order new cables along with the battery and gaskets. The are only $19.95
-
-
-
Prepara un iOpener (o utiliza un secador de pelo o una pistola de calor) y calienta la parte trasera del reloj para aflojar el adhesivo de la pila. Deja el iOpener sobre el reloj durante al menos dos minutos.
-
-
Yeah, bad links in step 11
I have edited the links to stay on the correct guide so they should work right once the edit is approved by the admins.
-
-
Inserta una púa de apertura entre la batería y el motor táptico.
-
Ejerce una presión constante y constante para levantar lentamente la batería, separándola del adhesivo que la sujeta a la placa base.
-
-
-
Utiliza el extremo plano de un spudger para hacer palanca y desconectar el conector de la batería.
-
-
-
Los siguientes cuatro pasos muestran cómo quitar la batería de un Apple Watch Series 6 de 44 mm.
-
Inserta una púa de apertura entre la batería y el motor táptico.
-
Ejerce una presión constante y firme para levantar lentamente la batería, separándola del adhesivo que la sujeta a la placa base.
My watch has a metal shield in between the battery and screen?
Hi Eric,
I assume you own the 40mm version of the Apple Watch series 6 which has a slightly different build. The one you see here is the 44mm version.
Is removing the battery really necessary if you are only replacing the display? I can't see in the following steps where the battery would get in the way of detaching the old screen.
I’ve already taken off the screen , had a bad scratch I couldn’t get out then totally messed it up so for $50 bucks and some increased knowledge of Apple Watches I have the 6 44mm and the whole screen is off took 2days, I’m a little afraid I may have taken off the lcd part as well and I just bought a digitizer and new battery i didn’t get anything called an lcd they were more expensive but I’ve looked for hours and I didn’t tear anything, any thoughts?
Hi Jeremy,
Unfortunately what the sites that sell just the digitizer (AKA the front glass) aren't telling you is that it's extremely difficult to separate the LCD and the digitizer, as they're bonded together with glue called OCA (Optically Clear Adhesive). It takes specialized skills and equipment to successfully separate them without damaging the delicate LCD, then even more equipment to rebond the display with a new digitizer. I consider myself a very experienced DIY guy and this isn't something I'd try on an Apple Watch. I have done one on a couple of iPhone 6's that turned out with barely acceptable results, and one on a Samsung phone that failed miserably.
Sorry to say, you'll need to bite the bullet and just buy a new screen assembly, one that includes both the LCD and the digitizer. Presumably you haven't done anything with the replacement part you already bought, so hopefully you can return it.
-
-
-
Saca con cuidado la batería de su hueco y colócala fuera de la caja del reloj, frente al motor táptico.
-
-
-
Retira el único tornillo Y000 de tres puntas de 1.2 mm de longitud.
-
-
-
Usa el extremo plano de un spudger para levantar y desconectar el conector de la batería.
-
Para volver a montar tu Apple Watch Series 6, sigue estas instrucciones en orden inverso. Aplica un poco de alcohol isopropílico de alta graduación (>90%) en un hisopo o utilice una almohadilla de limpieza para eliminar suavemente los restos de adhesivo en los bordes de la caja del reloj y la pantalla antes de instalar el nuevo adhesivo.
Para obtener un rendimiento óptimo, calibra tu batería recién instalada después de completar esta guía.
Lleva tus residuos electrónicos a un centro de reciclaje certificado.
¿La reparación no ha ido según lo previsto? Prueba con algunas soluciones de problemas básicos, o pide ayuda a nuestra comunidad de respuestas.
Para volver a montar tu Apple Watch Series 6, sigue estas instrucciones en orden inverso. Aplica un poco de alcohol isopropílico de alta graduación (>90%) en un hisopo o utilice una almohadilla de limpieza para eliminar suavemente los restos de adhesivo en los bordes de la caja del reloj y la pantalla antes de instalar el nuevo adhesivo.
Para obtener un rendimiento óptimo, calibra tu batería recién instalada después de completar esta guía.
Lleva tus residuos electrónicos a un centro de reciclaje certificado.
¿La reparación no ha ido según lo previsto? Prueba con algunas soluciones de problemas básicos, o pide ayuda a nuestra comunidad de respuestas.
Cancelar: No complete esta guía.
21 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
14 comentarios
Where do I purchase a replacement battery?
You can Google this. There are several sites offering batteries.
agrior -
Does the watch is still water resistant after replacing the battery ?
Not really, but I glue with certain types of glue and cure it for 1 hour and it seems to hold well. but I still wouldn't recommend going into pool.
You buy a new adhesive cut out. Ebay.
If you use b-7000 glue, yes.
Just completed the battery replacement for a series 6 40mm watch. The repair went smoothly, but now that it's all back together there are two bright blue vertical lines through the display. Any idea what I damaged? I'm assuming I damaged a cable or something and there is no fix, but I would like to know what I damaged so that I can be more careful next time.
It sounds like you damaged OLED. You will need new display for it but also want to make sure you transfer NFC chip in order to save Apple Pay function. but then, maybe it's time to upgrade.
Opening the case was difficult. Removing the battery was easy, but despite careful handling, the outer battery case became somewhat warped. I installed the new battery, and initially only the apple logo flashed... then after 20 minutes charging, the new battery showed 75 percent charged. I turned the unit off and completed the installation, sealing the case. Once finished, the watch only flashes the logo. The watch worked normally with the original battery, so suspect that the new battery is defective. Any similar experiences?
The guide doesn’t show how to install a new battery. Am I missing something?
Read the Conclusion section at the end; it gives you all the information you need in order to reassemble your watch with the new battery.