Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

Reemplazar el disco duro requiere separar la pantalla y quitar el altavoz izquierdo.

Esta guía incluye además los pasos para actualizar tu iMac con un disco SSD. Describe cómo instalar el sensor de temperatura del disco SSD para que los ventiladores funcionen a la velocidad correcta.

Antes de empezar cualquier trabajo en tu iMac: Desconecta el computador y mantén presionado el botón de encendido por diez segundos para descargar la corriente suministrada por los condensadores.

Sé muy cuidadoso de no tocar las patas de los condensadores ni ningún punto de soldadura expuesto por la parte trasera de la fuente de alimentación.

  1. Comenzando a la izquierda de la pantalla, cerca del botón de encendido, inserta la herramienta de apertura iMac en el espacio entre el panel de vidrio y la carcasa trasera. El centro de la herramienta de apertura iMac evitará que empujes demasiado la rueda. Si utilizas una herramienta diferente, inserta no más de 9.5 mm en la pantalla. Se corre el riesgo de cortar los cables de la antena y causar daños graves. El centro de la herramienta de apertura iMac evitará que empujes demasiado la rueda. Si utilizas una herramienta diferente, inserta no más de 9.5 mm en la pantalla. Se corre el riesgo de cortar los cables de la antena y causar daños graves.
    • Comenzando a la izquierda de la pantalla, cerca del botón de encendido, inserta la herramienta de apertura iMac en el espacio entre el panel de vidrio y la carcasa trasera.

    • El centro de la herramienta de apertura iMac evitará que empujes demasiado la rueda. Si utilizas una herramienta diferente, inserta no más de 9.5 mm en la pantalla. Se corre el riesgo de cortar los cables de la antena y causar daños graves.

    Would a heat gun make this step easier? Or damage the iMac?

    Clark Green - Contestar

    A heat gun wouldn’t help you here as you still need to cut though the adhesive. You also risk damaging the display with the excessive heat.

    Dan -

    Removing the original adhesive is easier than removing newly applied adhesive (e.g., if you have to reopen iMac).  If you should happen to need to reopen the iMac, please use extreme caution and highly consider my suggestions below.

    When using the pizza cutter tool, do the first few steps in reverse starting with step 8.  Starting on the left side is better since this is where the adhesive is narrowest.  The right side has two antennas and the top right has one, see the pictures for step 18-21, they are the brass colored metal rectangles near the edges.  The adhesive on these pieces are wider and therefore have more holding power.  The thickness of the pizza cutter tool is enough to crack the glass.

    Walter Hayden - Contestar

    Continuing from my previous comment.  To remove the adhesive on the right side you’ll need to create a very slight gap to give the pizza cutter some more room.  Do this by cutting the adhesive on the left side up and around to the camera.  Before attempting to cut the right side. Carefully slide the plastic cards (I purchased two sets) to ensure the adhesive on the left top and side is completely free.  Now slowly move towards the right side.  After every inch or two of removing new adhesive, slide the card over to create this slight gap.  Be careful to not move the card too close to where the adhesive has not been cut.  You want to create a very slight gap without creating too much pressure.  Use extra caution with approaching the areas where the antenna are since the adhesive is stronger here and will need some additional cutting.  Follow this approach all the way around the right side.  Be careful to not create too much pressure at any one time.  Good Luck!.

    Walter Hayden - Contestar

    I can confirm with Walter - trying to remove freshly applied adhesive is WAAAAY harder! My pizza cutter didn’t work correctly (the circle became a rectangle!) and I ended up with a small crack on the left of my screen. Dang it!

    Benon Koebsch -

    I would highly, highly, highly recommend AGAINST doing this at home. I followed these instructions to a T, and still somehow managed to have the screen not be able to turn on after the hard drive replacement. Then, once you’ve opened your Mac yourself, Apple will refuse to fix anything on the computer, and even other third party, Apple-authorized repair facility will refuse to repair it for you, and you will have to locate a non-authorized Apple repair facility. There, I am having to pay ~$600 to fix things that got screwed up, even though I followed the instructions here to a T, step by step, and did everything slowly and methodically.

    Beware, if you’ve never done this before, that be locked out of ever being able to use an Apple repair facility, or Apple-authorized repair facility, if you mess things up here now.

    Luke Gibson - Contestar

    I performed this on a Late 2015 iMac and there weren’t any significant differences to these steps, but I did find the repair to be nerve-wracking. My model cost nearly $3,000 and about 10 steps into this guide (which I did fully read ahead of time) I was thinking, “what have I got myself into?” But I didn’t rush and happily I’m typing this on my repaired iMac! I found a video from OWC that was more useful than the photos in this guide for certain steps: https://vimeo.com/139364064

    Anthony Zimmerman - Contestar

    Don’t know if you are still around, but THANK YOU for posting this video! The video made it seem SO NOT SCARY and, in conjunction with the photos and comments and tips on this guide, was a lifesaver. Big thumbs up.

    Melissa Ortiz -

    First impressions so far: yes it can be a bit nerve wrecking if it is your first time doing this sort of thing and even with lots of experience with a 2011 model it’s still a bit unsettling haha (nervous laughter).

    What I recommend: use a guitar pick to start cutting the glue. You’ll need a bit of pressure so do just the tip.

    Once you’ve done the whole perimeter (minus bottom) do it again but now it should be easier to go deeper so go very slow and careful. Then get the old suction cups used to open older models and start lifting the display very carefully to see where it’s still glued and cut those as well.

    Then you should be done and now the real fun begins! :D

    Carlos Ferrari - Contestar

    It’s ridiculous. Apple should pay for doing this. Like glue parts together to block a repair / make difficult. I smashed my iMac. FU Apple. Seriously, every product I owned had hardware issues. For example, bad solder joints. Never again Apple. I’m happy with Windows and in 2018 / 2019 there are many other manufacturers with high quality stuff. Apple is dying, if they do not change …

    Depple - Contestar

    NOTE: I followed every step word for word, but the adhesive strips supplied are as bad as double sided tape. Within 48hours the screen had slipped off and cracked. Now I need to fork out for a new screen and try again.

    Not sure what to try next time with strips? Perhaps a bit of glue to help hold it??

    Dan Kelly - Contestar

    Where do i get the “iMac Opening Tool?” its neither in the list of tools nor could i find it on the tool page.

    Patrick Cella - Contestar

    Hi @snappadoodle! The opening tool is included in the adhesive kit included in the tool list, but you can purchase it separately here.

    Sam Goldheart -

    After disconnecting the power cord and before cutting the panel adhesive, push and hold the power button for 10 seconds. This will discharge the power supply capacitors. In case you accidentally touch the solder joints on the board, you won't be shocked and drop the panel.

    Paul Floro - Contestar

    Bottom line: This repair seems to have worked (so far no more intermittent shut-downs). Thanks iFixit!

    As a novice who fully expected to destroy the display or worse, I make the following recommendations: (1) Before you start, read the steps several (many) times; visualize doing them and imagine how things could go wrong; (2) Read all the comments—there were some really helpful tips—like simply displacing the left speaker rather than fully removing it; (3) Get the recommended tools*; and (4) take your time—if you start to feel frustrated—seriously, stop and take a calming breath. Time is your friend. Failure is not an option.

    *I would add a 3-prong parts puller to the tool list—it’s great for pulling and starting loose screws so you don’t drop them down into the chassis like I did. It’s also great for retrieving the screws you’ve dropped into the chassis.

    Brad Bauknecht - Contestar

    Hi brad, what exactly did you repair to stop the shutdowns? I’m having the same issue

    merinian -

    Just completed the Core i5 to i7 CPU upgrade and can strongly recommend getting the “pizza tool” to cut the display adhesive. It worked flawlessly and was done in less than 5 minutes. No inadvertent cables cut. No display problems.

    John Fisk - Contestar

  2. Use la herramienta como un cortador de pizza: gírelo a lo largo del espacio y cortará el adhesivo de espuma a través del centro. Asegúrese de empujar siempre con la manija detrás de la rueda de corte. Si tira, la rueda podría salirse del mango. Ejecute la herramienta hacia arriba a lo largo del lado izquierdo de la pantalla.
    • Use la herramienta como un cortador de pizza: gírelo a lo largo del espacio y cortará el adhesivo de espuma a través del centro.

    • Asegúrese de empujar siempre con la manija detrás de la rueda de corte. Si tira, la rueda podría salirse del mango.

    • Ejecute la herramienta hacia arriba a lo largo del lado izquierdo de la pantalla.

    I found the 'pizza cutter' surprisingly smooth at cutting through four-year-old adhesive.

    Gerry - Contestar

    In my experience the cutter also worked very well for cutting the original adhesive. Unfortunately when I was reinstalling the display with the new adhesive strips, somehow the display power connector came loose. I had to open the display a second time and the cutter was not as effective against the new adhesive. I managed to break the cutter tool plastic wheel and cause a few small cracks in the edge of the displays glass as I worked! Be careful and go slowly!

    azaadkb - Contestar

    The cutting tool worked great until I accidentally twisted it a bit while rounding a corner. A chunk of the wheel snapped off, making the rest of the job quite a bit more challenging. Just make sure you are keeping the tool directly parallel with the screen.

    BARRY RODRIGUEZ - Contestar

  3. Continúe girando la herramienta hacia arriba en la esquina superior izquierda. Continúe girando la herramienta hacia arriba en la esquina superior izquierda. Continúe girando la herramienta hacia arriba en la esquina superior izquierda.
    • Continúe girando la herramienta hacia arriba en la esquina superior izquierda.

  4. Corte el adhesivo a lo largo de la esquina superior izquierda de la pantalla. Corte el adhesivo a lo largo de la esquina superior izquierda de la pantalla.
    • Corte el adhesivo a lo largo de la esquina superior izquierda de la pantalla.

    The pizza cutter will sink in all the way to the tool handle when the adhesive is full cut, but don’t feel you have to do this in one motion. Some parts cut easier and some require a lot (like 20x) of gentle back and forth.

    Anthony Zimmerman - Contestar

  5. Continúa por la parte superior de la pantalla. Es posible que desee ejecutar la herramienta hacia adelante y hacia atrás a través de lo que ya ha cortado un par de veces, para asegurarse de obtener la mayor cantidad de adhesivo separado como sea posible.
    • Continúa por la parte superior de la pantalla.

    • Es posible que desee ejecutar la herramienta hacia adelante y hacia atrás a través de lo que ya ha cortado un par de veces, para asegurarse de obtener la mayor cantidad de adhesivo separado como sea posible.

    what about the part where the camera is though? do I just treat it like the rest of the screen?

    Boris - Contestar

    yes. the tool can’t go too deep

    flow in - Contestar

  6. Empuje la herramienta alrededor de la esquina superior derecha de la pantalla. Empuje la herramienta alrededor de la esquina superior derecha de la pantalla. Empuje la herramienta alrededor de la esquina superior derecha de la pantalla.
    • Empuje la herramienta alrededor de la esquina superior derecha de la pantalla.

  7. Mueva la herramienta hacia abajo a lo largo del lado derecho de la pantalla. Mueva la herramienta hacia abajo a lo largo del lado derecho de la pantalla.
    • Mueva la herramienta hacia abajo a lo largo del lado derecho de la pantalla.

  8. Finalice empujando la herramienta de apertura hacia la parte inferior del lado derecho de la pantalla. En este punto, querrá volver a ejecutar la herramienta en toda la pantalla para asegurarse de cortar la mayor cantidad de adhesivo posible.
    • Finalice empujando la herramienta de apertura hacia la parte inferior del lado derecho de la pantalla.

    • En este punto, querrá volver a ejecutar la herramienta en toda la pantalla para asegurarse de cortar la mayor cantidad de adhesivo posible.

  9. Si bien la herramienta de apertura hizo la mayor parte del trabajo, la pantalla aún se adherirá ligeramente a la carcasa. Se necesitará una tarjeta de plástico para liberar el último adhesivo. Coloca el iMac boca arriba en una mesa. Comenzando desde la esquina superior derecha del iMac, inserta una tarjeta de plástico entre la pantalla y el marco.
    • Si bien la herramienta de apertura hizo la mayor parte del trabajo, la pantalla aún se adherirá ligeramente a la carcasa. Se necesitará una tarjeta de plástico para liberar el último adhesivo.

    • Coloca el iMac boca arriba en una mesa.

    • Comenzando desde la esquina superior derecha del iMac, inserta una tarjeta de plástico entre la pantalla y el marco.

    • Ten cuidado de no insertarlo más de 9.5 mm o podrías dañar los componentes internos.

    I actually DESTROYED my display (black vertical strips) by pushing the card in a bit TOO DEEP. So it is REALLY important to insert the card only a bit (1-2mm) more than the cutter wheel, in particular at the top side, where many flat cables connect the panel with the PCB. These can be damaged very easily!

    Peter Fischer - Contestar

    Same thing with me…. Pushed cards to far…. new panel needed…€600…..

    i think ifixit needs to place a bigger caveat, as I have missed it the first time

    Edgar Broekema - Contestar

    i successfully upgraded two imacs. one opened with ifixit pizza knife and another with a regular paper knife. however, when i had to open the first one once again i broke its screen glass. it seems ifixit adhesive strips are too strong. next time i’ll try to use heater to weaken glue tension.

    Eugene Kharkov - Contestar

    I broke one too. And even if you think you did it correctly, you’ll not be able to see where you might have gone too far. You would think it’s very protected behind that metal plate, but no. Take special care with this offence to “right to repair” This should have been designed WAY better. I mean replacing a hardrive that is very likely to fail over the course of time, or even a simple desire to upgrade to an ssd!.

    Bummer

    Denis Sytmen - Contestar

    HINT: If you turn the card and use the blue part of it, then you can avoid going to deep: no further then the blue part …

    Barthold - Contestar

    On the cards I got with my iFixit kit, the blue part was way bigger than 9.5mm — closer to 20mm!

    I made a line 9mm from the edge of each of my cards and used that as a guide.

    Damian Chadwick -

    I’m thinking I might just use vinyl tape to keep the screen in place for at least a little while after an upgrade. The extra strength of the replacement tape sounds scary.

    Art Hackett - Contestar

    I wrapped two layers of vinyl electrical tape around the short side of an old gift card 3/8” from the edge. This “stop" prevented the card from going in too far. The card really helps to break the panel free.

    Paul Floro - Contestar

    This is a good tip!

    Lennart Saaf -

    Umm.. I’m not sure that I’d recommend using a repurposed credit card to open the display - I found that using the “pizza tool” to cut the old adhesive then using a pair of suction cups to gently pull the display up worked perfectly well.

    John Fisk - Contestar

    surely the card should have been designed such not to go further than certain distance with a barrier band.

    S Hussain - Contestar

  10. Gira suavemente la tarjeta de plástico para abrir el espacio entre la pantalla y el marco, y corta cualquier resto de adhesivo en la esquina. Si usas demasiada fuerza, romperás el cristal. Trabaja con cuidado, y no intentes hacer un espacio de más de 6 mm.
    • Gira suavemente la tarjeta de plástico para abrir el espacio entre la pantalla y el marco, y corta cualquier resto de adhesivo en la esquina.

    • Si usas demasiada fuerza, romperás el cristal. Trabaja con cuidado, y no intentes hacer un espacio de más de 6 mm.

    My children tend to collect cards like this from hotels, Disneyland, old IDs, iTunes cards, gift cards etc. They came in handy for this step. After wedging in the first card into the left corner, I wedged the left corner, then added cards along the bottom edge. Finally I continued to push in additional cards to existing cards and found that this created a smooth even pressure along the display top. At 2-3 card-thickness the last of the adhesive let go, gentle as a baby.

    Anthony Zimmerman - Contestar

  11. Asegúrese de detener el corte antes de la cámara iSight en este paso, o puede dañarlo. Deslice la tarjeta hacia el centro de la pantalla para cortar el adhesivo restante. Deslice la tarjeta hacia el centro de la pantalla para cortar el adhesivo restante.
    • Asegúrese de detener el corte antes de la cámara iSight en este paso, o puede dañarlo.

    • Deslice la tarjeta hacia el centro de la pantalla para cortar el adhesivo restante.

    was denn jetzt? Vor der Kamera aufhören, oder in Richtung Bildschirmmitte schieben, um DEN REST zu entfernen? Wenn ich vor der Kamera aufhöre, kann ich nicht alles an Kleber entfernen.

    Julia S. - Contestar

  12. Vuelva a colocar la tarjeta en la esquina y déjela allí para evitar que se reubique el adhesivo. Vuelva a colocar la tarjeta en la esquina y déjela allí para evitar que se reubique el adhesivo.
    • Vuelva a colocar la tarjeta en la esquina y déjela allí para evitar que se reubique el adhesivo.

  13. inserte una segunda tarjeta en el espacio entre la pantalla y el marco en la esquina superior izquierda. inserte una segunda tarjeta en el espacio entre la pantalla y el marco en la esquina superior izquierda. inserte una segunda tarjeta en el espacio entre la pantalla y el marco en la esquina superior izquierda.
    • inserte una segunda tarjeta en el espacio entre la pantalla y el marco en la esquina superior izquierda.

  14. Gire suavemente la tarjeta, aumentando ligeramente el espacio entre la pantalla y el marco. Al igual que con el otro lado, muévase lentamente para permitir que se rompa el adhesivo, y tenga cuidado de no sobre tensar el cristal de la pantalla.
    • Gire suavemente la tarjeta, aumentando ligeramente el espacio entre la pantalla y el marco.

    • Al igual que con el otro lado, muévase lentamente para permitir que se rompa el adhesivo, y tenga cuidado de no sobre tensar el cristal de la pantalla.

  15. Deslice la tarjeta de plástico hacia el centro, deteniéndose de nuevo justo antes de la cámara iSight. Deslice la tarjeta de plástico hacia el centro, deteniéndose de nuevo justo antes de la cámara iSight. Deslice la tarjeta de plástico hacia el centro, deteniéndose de nuevo justo antes de la cámara iSight.
    • Deslice la tarjeta de plástico hacia el centro, deteniéndose de nuevo justo antes de la cámara iSight.

  16. SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

    SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación
  17. Inserta la tarjeta nuevamente en la esquina superior izquierda. Inserta la tarjeta nuevamente en la esquina superior izquierda.
    • Inserta la tarjeta nuevamente en la esquina superior izquierda.

  18. Solo levante la pantalla unas pulgadas; todavía está conectada al iMac mediante cables de datos y alimentación. Con las tarjetas insertadas como se muestra cerca de las esquinas, gire suavemente las tarjetas para aumentar el espacio entre la pantalla y la carcasa. Si hay secciones que parecen pegarse y no se separan, deje de girar y use una de las tarjetas para cortar el adhesivo en el área problemática.
    • Solo levante la pantalla unas pulgadas; todavía está conectada al iMac mediante cables de datos y alimentación.

    • Con las tarjetas insertadas como se muestra cerca de las esquinas, gire suavemente las tarjetas para aumentar el espacio entre la pantalla y la carcasa.

    • Si hay secciones que parecen pegarse y no se separan, deje de girar y use una de las tarjetas para cortar el adhesivo en el área problemática.

    • Comience a levantar la parte superior de la pantalla desde el marco.

    I would recommend using suction cups at this stage to lift the display.

    Marco De Palma - Contestar

    I would strongly recommend using suction cups

    Luca Mucci - Contestar

    Agreed about the suction cups. An extra pair of hands might be good here as well.

    Damian Chadwick - Contestar

    I agree, I’m using iFixit suction cups right now.

    tanner85 - Contestar

    Go very slowly when lifting the display – give time for the adhesive at the bottom edge to stretch and flow. If you lift too fast, the glass can crack. That’s what happened for me.

    Gerry - Contestar

    The stickiest location on my iMac was the mid-to-lower section of the right side. There are a couple of thicker areas that needed attention from the plastic cards.

    Lennart Saaf - Contestar

  19. Mientras sostiene la pantalla con una mano, use la otra para desconectar el cable de alimentación de la pantalla. Levante la pantalla lo suficiente para tener un acceso fácil a las conexiones, pero no tanto que estire los cables y acentúe sus conexiones (aproximadamente 8 ").
    • Mientras sostiene la pantalla con una mano, use la otra para desconectar el cable de alimentación de la pantalla.

    • Levante la pantalla lo suficiente para tener un acceso fácil a las conexiones, pero no tanto que estire los cables y acentúe sus conexiones (aproximadamente 8 ").

    Mark all cable connectors with a spot of white correction fluid before removal. This will remove the risk, when reinserting them later, of getting them the wrong way round. Yes - I know they will only plug in one way round, but it does make life easier if you are not in perfect lighting!

    Alastair Lack - Contestar

    At this step, if you mess up anything with these 2 cables, especially when plugging them back in, even if you think you’re following the instructions here to a T, then you’re screwed.

    I would highly, highly, highly recommend AGAINST doing this at home. I followed these instructions to a T, and still somehow managed to have the screen not be able to turn on after the hard drive replacement. Then, once you’ve opened your Mac yourself, Apple will refuse to fix anything on the computer, and even other third party, Apple-authorized repair facility will refuse to repair it for you, and you will have to locate a non-authorized Apple repair facility. There, I am having to pay ~$600 to fix things that got screwed up, even though I followed the instructions here to a T, step by step, and did everything slowly and methodically.

    Beware, if you’ve never done this before, that be locked out of ever being able to use an Apple repair facility, or Apple-authorized repair facility, if you mess things up here now.

    Luke Gibson - Contestar

    The display cable, the wider one, has a lock on it , usually a plastic tape lift tab to release it, once thats flipped it should come out fairly easily, if your experiencing resistance and the cable isn’t coming out then check for this lock/latch, the power cable just pulls out, just don’t rush it everything should go fine, fairly easy to do with the end result a working iMac

    Ed tabickman - Contestar

    Is it possible to replace the power cable if its damaged? I can’t seem to find anything about this.

    Joseph Orr - Contestar

    After finishing my hard drive replacement I reconnected these connectors to test my display before using new adhesive. Everything was working beautifully. But then when I applied the new adhesive and went to seal the display on for good - the display power cable somehow became disconnected! I had to reopen the Mac for a second time which was far more difficult with new adhesive. When reinstalling double and triple check that the cables are securely inserted before the final seal. Sounds obvious but it’s quite the annoyance if something goes wrong at this point.

    azaadkb - Contestar

    Very difficult to work with these connectors.

    Power cable very difficult to unplug - data cable veeeeery difficult to plug in.

    I noticed that working with the iMac positioned vertically (and with a proper support for inclination) makes this step slightly easier…

    Luca Mucci - Contestar

    Interesting comments.. personally, I didn’t find the cables particularly difficult to detach and reattach. You do have to be patient and gentle. Personally, I found that a rolled up beach towel gently wedged between the unit and back of the display helped keep the glass up. Also, a small flashlight can be helpful to see the cables and connectors if you’re lighting isn’t perfect.

    John Fisk - Contestar

  20. Levante el soporte de retención de metal en el cable de datos de la pantalla. Desconecte el cable de datos de la pantalla. Esta es una conexión delicada que se puede romper fácilmente. Asegúrese de sacar el conector del cable de datos de la pantalla directamente de su zócalo, hacia la parte superior del iMac.
    • Levante el soporte de retención de metal en el cable de datos de la pantalla.

    • Desconecte el cable de datos de la pantalla.

    • Esta es una conexión delicada que se puede romper fácilmente. Asegúrese de sacar el conector del cable de datos de la pantalla directamente de su zócalo, hacia la parte superior del iMac.

    I replaced HDD to SSD and assembled parts again. When I boot up the iMac, I found black lines on display (looks partly not broken).

    I searched Internet, and some says graphic card problem, but I didn't touch anything but cable to lift up.

    Could the damaged display data cable cause this situation? I hope I could fix this by just replacing the cables..

    chansung park - Contestar

    Sorry, Black lines is a damaged display assembly ;-{ In the process of removing it you either pushed the tool into deep or you torqued the glass severing the tiny wire traces.

    Dan -

    Same trouble here, is it cable trouble or connector trouble?

    redfoxydarrest - Contestar

    Sorry damaged display

    Dan -

    I think whenever words like "...is a delicate connection that can be broken. Be sure to pull the [cable in a certain direction] ANYTIME.... It is worth either a closeup or 2, maybe one with annotations or insertion directions and maybe a motion direction arrow with the something like and 'X' char or a circle division slash over the wrong one.

    john - Contestar

    I agree! +1

    Jim Reitz -

    Yes, John is absolutely correct on this one. I damaged the display cable trying to get it back in. A close up would have helped and now my computer might have actually been fixed.

    Marsha Giardina -

    [|There are 2 cables to disconnect on my Mac (?). Also, I don’t see a metal retaining bracket. I can take a picture, but cannot attach. I got the glass loose with no problem, but am worried about damaging the cables]

    Jim Kelly - Contestar

    Hi Jim! You can go to our Answers Forum to post some better images of your situation!

    Sam Goldheart -

    At this step, if you mess up anything with these 2 cables, especially when plugging them back in, even if you think you’re following the instructions here to a T, then you’re screwed.

    I would highly, highly, highly recommend AGAINST doing this at home. I followed these instructions to a T, and still somehow managed to have the screen not be able to turn on after the hard drive replacement. Then, once you’ve opened your Mac yourself, Apple will refuse to fix anything on the computer, and even other third party, Apple-authorized repair facility will refuse to repair it for you, and you will have to locate a non-authorized Apple repair facility. There, I am having to pay ~$600 to fix things that got screwed up, even though I followed the instructions here to a T, step by step, and did everything slowly and methodically.

    Beware, if you’ve never done this before, that be locked out of ever being able to use an Apple repair facility, or Apple-authorized repair facility, if you mess things up here now.

    Luke Gibson - Contestar

    Can anybody upload an image of how the display can get damaged from removing it? I find it hard to believe (though I’m reading the horror stories here) that a whole display can get damaged. Especially when many of us were following to a T and being VERY CAREFUL.

    Thanks.

    Bryan - Contestar

    First: During reassembly, I highly recommend you connect these cables and do a test boot BEFORE you remove the protective tape on the adhesive strips. That way you can fix any issues(like a damaged cable) if something is not right and you have not re-glued the screen back down which will cause a problem. If you have a second person and everything is working after test boot, you can just leave the cables connected, lift the bottom of the screen and have 2nd person pull the protective tape on the adhesive strips and you can set the screen in place. Second I damaged the video data cable during reassembly on my late 2015 iMac- I did not get the connector straight and I damaged the wires on the cable. I recommend you have someone else hold the screen while you attach the cables - they are fragile. Luckily, the data cable was easily replaced for only about $20. If you must do this by yourself, just be careful I highly recommend have 2 people at this step during reassembly.

    Chip T - Contestar

    At least on my “late 2013” model, the smaller display cable connector has tiny, tiny clips on the outside edges. These must be squeezed to unlatch it. Don't pull on the cable itself or the wires can be pulled out. Even with my small fingers, it was hard to grip the clips. When reconnecting, the connector will lightly snap into place.

    Paul Floro - Contestar

    I managed this step without any problems, but I had my wife hold the screen up while I disconnected/connected the cables. I STRONGLY encourage another pair of hands here so you can focus your full attention on being ultra careful with the cables.

    BARRY RODRIGUEZ - Contestar

    On the 2015 there are 2 cables.

    1. Once the display is loose use the Mac foam block sold from Ifixit to keep the display from rocking to hold open the glass

    2. Blow out dust with canned air

    3. Get a flash light and small flat edged screw driver

    4. Use the screw driver to slow pry loose the connector from the socket by gently inserting it in the gap on the left and then on the right slowly easing the connector from the socket towards the top of the glass

    5. The more center connector has a pull tape and a wire loop. Lift pull tape and the wire loop will raise up.

    6. Pull the wire loop towards the top of the glass to slide out the connector from its socket

    Anthony Crocker - Contestar

    Have a late 2013 model and went to do the SSD upgrade. When going to remove the display we cracked the bottom left corner of the glass (just the glass frame part - not part of the screen that displays anything). We were also having difficulty putting re-attaching the display flex cable. Whenever we finally went to test it before re-sealing the screen back on with new adhesive it would sound like it is turning on as it makes boot-up noises and the fans start running, but the screen would just remain black. Just wondering if the crack in the bottom left-hand side of the glass/display would have damaged a part of the display assembly or if it would be more likely that we just damaged the display flex cable (which can be replaced for $26)?

    Zach Tweel - Contestar

    does anybody know how the Display Cabel pin assignment is? I want to try if I can attach the Panel to another grafic card

    Marco Rizzo-Scheible - Contestar

    I’ve completed the upgrade to SSD, but while restarting my screen remains black. As if no connected.

    I assume I broke the sensitive connector.

    —> how to order a spare?

    Durain - Contestar

  21. Levante la pantalla hasta una posición casi vertical. En este punto, todavía hay una tira de adhesivo en la parte inferior de la pantalla, que mantendrá la pantalla en el marco como una bisagra. Puede aflojar este adhesivo al subir y bajar la pantalla varias veces.
    • Levante la pantalla hasta una posición casi vertical.

    • En este punto, todavía hay una tira de adhesivo en la parte inferior de la pantalla, que mantendrá la pantalla en el marco como una bisagra. Puede aflojar este adhesivo al subir y bajar la pantalla varias veces.

    • Retire la mayor cantidad de adhesivo posible agarrándolo por los bordes exteriores, y luego tirando o rodando hacia el centro.

    Thank you Stef, that's what i will do next time, i cracked the lower part of the screen went opening very slowly, that's probably why those "tabs are for !!

    dforgues - Contestar

    Thanks Stef, this has saved me! Simple yet very effective.

    David Zemsky - Contestar

    Yep, I cracked the lower corner of the display as well. I failed to work the adhesive enough to loosen it sufficiently. Be careful, I just had to buy my customer another screen!

    Peter Haigh - Contestar

    There seems to be missing a step or two. As I was removing the old display, there are two wires that need to get transferred to the new replacement display. There is not note about these two wires located at the top of the display. The 1.128-inch ribbon cable and then this other 4-inch long, two-wire cable that goes to a very small circuit board that is 1/4 by 3/8 of an inch and seems to be adhered to the panel.I have not been able to get this cable off the old display. There is a port for it on the replacement display.

    Note: When ordering this screen, and plastic cards as noted tools, ifixit.com did not list the pizza cutter or the new replacement adhesive strips. So now I’m not sure how to get the new one on and secure.

    Todd Derek - Contestar

    The adhesive strip along the bottom is designed with a pull tab on each outer end. Rather than lever and pull the screen simply carefully pull the tab which removes that half of the lower adhesive strip and frees up the screen.

    Andrew Stephens - Contestar

    Niemals den unteren Klebestreifen mit einem scharfen Gegenstand wie Rasierklinge oder so versuchen zu trennen, davon geht die Beschichtung des Displays kaputt und man hat hässliche Streifen unten hinter dem Glas. Stattdessen lieber versuchen, das Display nach oben zu klappen und abzuziehen.

    Bas ti - Contestar

    translation from Bas Ti because this is very important:

    Never try to separate the bottom adhesive strip with a sharp object such as a razor blade or something, the coating on the display will break and you will have ugly strips at the bottom behind the glass. Instead, try to flip up and pull off the display.

    Kurt Grootjans - Contestar

  22. Tenga mucho cuidado de no tocar los cables del condensador ni las juntas de soldadura expuestas en la parte posterior de la fuente de alimentación (enmarcadas en rojo). Si es necesario, se puede usar una tarjeta de plástico para cortar las secciones restantes de la tira adhesiva inferior.
    • Tenga mucho cuidado de no tocar los cables del condensador ni las juntas de soldadura expuestas en la parte posterior de la fuente de alimentación (enmarcadas en rojo).

    • Si es necesario, se puede usar una tarjeta de plástico para cortar las secciones restantes de la tira adhesiva inferior.

    Would have been helpful to box the same red area when using the plastic card to separate the glue. Since the red blocked picture is inverted, if someone doesn't pay close attention it may not be obvious that the area of concern is at the right top of the graphic pictures in which the plastic card use is being demonstrated..

    Wizbang FL - Contestar

    you don't need to cut the bottom part as the bottom tape is stuck on each side and you can easily pull it out

    Thomas Webb - Contestar

    What is the twisted wire taped to the back of the display that can bee seen in the upper right of the first two pictures? I have an 27” iMac without a screen an my replacement does not have this wire. I think it is a temperature sensor but do not know where it connects to.

    Eric - Contestar

    [|I opened up my iMac and there’s no HDD or SSD in that spot. its just empty.]

    John Warmann - Contestar

    Please update the picture to include the RED BOXED IN AREA that you refer to on all three pictures in this step. I have had a few zaps from these supplies and it is not pleasant.

    Charlie Nancarrow - Contestar

    J’ai réussi à intervenir dans l’iMac sans décoller l’ensemble de l’écran. Je l’ai ouvert en laissant la dernière partie collée (vers le logo Apple) et qui sert comme une charnière. Bien calé et assuré l’écran n’a pas bougé et j’ai pu changer mon disque dur facilement. Le grand avantage et d’avoir l’écran toute suite juste quand on le recolle par la suite.

    David Mariaux - Contestar

    Well, I of course touched a soldering point in the red area as my hand slipped. I heard and felt a tiny “click” and after replacing the HDD with SSD etc I can not power the iMac up anymore. Not a sign of life :-( I suppose I broke the power supply. Can someone confirm? Or could something else have broken too?

    David Rosner - Contestar

    @john - there’s a slot on the back of the motherboard for a storage stick. fancy

    flow in - Contestar

  23. Ten mucho cuidado al manipular la pantalla: es grande, pesada y está hecha de vidrio. Además, tiene bordes frágiles. Evita levantar la pantalla por las esquinas. Levanta la pantalla del marco y retírela del iMac. Coloca la pantalla hacia abajo en una superficie plana y suave. Podría ser necesario levantar lentamente de un lado, para poder eliminar el adhesivo restante.
    • Ten mucho cuidado al manipular la pantalla: es grande, pesada y está hecha de vidrio. Además, tiene bordes frágiles. Evita levantar la pantalla por las esquinas.

    • Levanta la pantalla del marco y retírela del iMac. Coloca la pantalla hacia abajo en una superficie plana y suave.

    • Podría ser necesario levantar lentamente de un lado, para poder eliminar el adhesivo restante.

    • Después de haber cortado el adhesivo, no podrás reutilizarlo para volver a sellar la pantalla en su posición original. Sigue esta guía al completar su reparación para remplazar las tiras de adhesivo que podrán asegurar la pantalla de nuevo a la carcasa trasera.

    You really should be using film handling or surgical type gloves to handle the screen to minimise finger grease on any of it. Even if it’s possible to clean most of it off, it can be corrosive over time.

    Art Hackett - Contestar

  24. Si estás remplazando la pantalla, puede ser que necesites transferir más componentes desde el panel antiguo al nuevo. Compara la parte trasera de la pantalla antigua y la nueva pantalla. Anota qué cables, sensores y cojines de acolchamiento no están presentes en la nueva pantalla.
    • Si estás remplazando la pantalla, puede ser que necesites transferir más componentes desde el panel antiguo al nuevo. Compara la parte trasera de la pantalla antigua y la nueva pantalla. Anota qué cables, sensores y cojines de acolchamiento no están presentes en la nueva pantalla.

    • Si hay un alambre o cable debajo de una cinta adhesiva, siempre separa la cinta primero.

    • Si el cable está pegado a la estructura, usa un iOpener calentado o un secador de pelo primero para soltar el adhesivo. Entonces podrás introducir una púa de apertura por debajo del cable para aflojarlo. Nunca tires directamente de los conectores delicados.

    • Desliza una púa de apertura por debajo de los cojines de acolchamiento para separarlos de la pantalla, y tira de ellos con cuidado. Podrías necesitar algo de cinta de doble cara para unirlos a la nueva pantalla.

    Be extremely careful removing the LCD Temp Sensor from the rear of the screen. If you pull the wire, you run the risk of severing the metal wire from the connector but not notice it because the surrounding plastic insulation may still be intact. Use a razor blade so “shave off” the sensor under the adhesive. I just had the screen replaced by a local shop and, upon boot, the fan was running full-speed and the Mac’s speed was miserable; Excel took 30 bounces in the Dock to launch rather than the expected 4-5. Novabench showed the Mac running at 4% of its expected speed (overall). The tech examined the sensor carefully, found the broken connection, soldered it back into place, and all was fine. Note that the (partially disconnected) sensor actually showed up when I ran Macs Fan Control in an attempt to work-around this. No problem controlling the fan speed then but the iMac’s running speed was awful until the disconnected sensor wire was fixed.

    barryjaylevine - Contestar

    Hi barryjaylevine,

    I’ve had my LCD replaced on my iMac 27 / 2013 and there is no LCD Temp Sensor cable on the replacement screen.

    I’m experiencing the same performance issues.

    I’ve ordered a new sensor, do you have any pointers as to how to install it?

    Thanks,

    Simon

    UK

    simon kennedy -

    hey Simon, I used 2-sided tape….this is assuming the new sensor doesn’t already come with an adhesive surface already applied.

    a roll of kapton tape for your own peace of mind will make sure nothing detaches from thermally-induced adhesive crystallization

    make sure you position it in such a way that you can easily plug the lead back into the mobo….not a lot of length to that wire

    placebomessiah - Contestar

    Howdy folks,

    Thanks for all the tips, LCD sensor fitted and iMac back in action.

    Never again!

    Simon

    simon kennedy - Contestar

    Hello all. So I’m trying to pinpoint my backlight issue on my 2015 retina 5k - I noticed I’m missing my thermal sensor on the LCD. Would this help with the backlight? I’m sure it will keep my fans from going crazy. Any help would be appreciated! Note: I have LEDs except the 4th one. Thanks!

    Jordan Shababy - Contestar

    Be careful when removing the adhesive residue!

    I didn’t know it, but I ended up leaving slight scratch marks that can be seen from the front side.

    Eric - Contestar

    • Con la bisagra libre para moverse, el iMac estará desequilibrado y difícil de trabajar. Las reparaciones se pueden completar con el iMac, pero son más rápidas y fáciles con una cuña de servicio iMac.

    Incomplete guidance . Does not say how to transfer cables such as thermal sensor .

    Yuan - Contestar

    La traduction française est tronquée : “…plus faciles avec une cale de maintien pour iMac”

    (https://eustore.ifixit.com/fr/Outils/Org...)

    Pierre-Aurélien - Contestar

    My $12.99 iMac Service Wedge looks like a $0 soft pillow from the guest room…

    ;-)

    John Fisk - Contestar

  25. Quita los dos tornillos T10 de 10.0mm.
    • Quita los dos tornillos T10 de 10.0mm.

    If you just want access to the HD, there is no need to remove any speaker wires - it slides over enough to access the HD screws.

    johann beda - Contestar

    No need to remove speaker or hard drive to replace power supply. Not clear at all why these steps are included.

    nicejob - Contestar

    *** Skip directly to Step 31 if you’re just replacing the hard drive. These next steps are totally unnecessary for that! They just add complexity and increase the chances for something going wrong. ***

    Damian Chadwick - Contestar

    Avoid Extra Steps! Again, you DO. NOT. NEED. TO. REMOVE. THE. RIGHT. SPEAKER. Just take out the two speaker mounting screws and scoot the speaker enclosure to the left a bit to access the two Hard Drive bracket screws on the left side. Once you remove the two bracket screws you can easily remove / replace the drive.

    clinton - Contestar

    Came back just to say what everyone else has said: you really don’t need to take out the whole speaker. You can just loosen the two screws and move it aside to access the drive/put the new one in. Saves a lot of effort.

    Melissa Ortiz - Contestar

  26. Desconecta el cable del altavoz izquierdo de su zócalo en la placa base. Asegúrate de tirar hacia arriba paralelo al zócalo. Retire el cable a través del espacio entre el disco duro y la placa base. Si el espacio entre el disco duro y la placa base es demasiado estrecho para el cable del altavoz, desconéctalo y déjalo donde está.
    • Desconecta el cable del altavoz izquierdo de su zócalo en la placa base. Asegúrate de tirar hacia arriba paralelo al zócalo.

    • Retire el cable a través del espacio entre el disco duro y la placa base.

    • Si el espacio entre el disco duro y la placa base es demasiado estrecho para el cable del altavoz, desconéctalo y déjalo donde está.

    I didn’t unplug and de-route this cable. Later, Step 29, has you remove the left speaker. This isn’t necessary. If you can just move the speaker over to expose the hard drive mounting screws, so if you’re not going to remove the speaker, you don’t need to unplug it.

    Anthony Zimmerman - Contestar

  27. Ten cuidado con no tocar ninguna de las soldaduras de la parte trasera de la fuente de alimentación. Los condensadores podrían contener suficiente corriente como para darte una descarga peligrosa. Usa un spudger para desconectar la conexión del botón de encendido de su ranura en la placa base. Usa un spudger para desconectar la conexión del botón de encendido de su ranura en la placa base.
    • Ten cuidado con no tocar ninguna de las soldaduras de la parte trasera de la fuente de alimentación. Los condensadores podrían contener suficiente corriente como para darte una descarga peligrosa.

    • Usa un spudger para desconectar la conexión del botón de encendido de su ranura en la placa base.

    Can someone explain what are the solder joint? Or tell me what it looks it?

    brianyu - Contestar

    The silver spots on the circuit boards. You may not want to tackle this alone. If you touch these areas, you can possible get a shock -- harming you and your computer.

    Robert -

    there is no need to disconnect the speaker, just unscrew it and move aside slightly to reach the HDD screws (about 5mm) - if you want to replace just the main HDD

    Thomas Webb - Contestar

    Take note of exactly what direction this tiny little wire was.

    Joseph Ashe - Contestar

    If I leave my iMac unplugged for an extended period, say 24 or 48 hours, is it still possible to get an electric shock from the PSU? Do the capacitors eventually discharge?

    Dominic Pettifer - Contestar

    make sure you’ve actually unplugged the mac when running this cable, and not had it plugged in to test the diagnostic LEDs, because one of those wee silver spots is carrying 230v, and its 6mm away from the place the cable runs, So if you have fat fingers like mine, that’s a free wake up zap

    flow in - Contestar

  28. Levanta el altavoz izquierdo, hasta que puedas ver el cable del botón de encendido (unas 0.5 pulgadas/1.2 cm). Levanta el altavoz izquierdo, hasta que puedas ver el cable del botón de encendido (unas 0.5 pulgadas/1.2 cm).
    • Levanta el altavoz izquierdo, hasta que puedas ver el cable del botón de encendido (unas 0.5 pulgadas/1.2 cm).

  29. Desconecta con cuidado el cable del botón de encendido de su muesca en el altavoz izquierdo. Desconecta con cuidado el cable del botón de encendido de su muesca en el altavoz izquierdo. Desconecta con cuidado el cable del botón de encendido de su muesca en el altavoz izquierdo.
    • Desconecta con cuidado el cable del botón de encendido de su muesca en el altavoz izquierdo.

    Pay attention: if pulling out the loudspeaker tear off the wire of the power button, Apple have not any service parts except for the whole rear housing!

    Fabio Braga - Contestar

  30. Levanta el altavoz izquierdo y sepáralo del iMac. Si el espacio entre el disco duro y la placa base era demasiado estrecho para que el altavoz pudiera separarse, empuja con cuidado mientras lo separas. Empuja desde el terminal del conector, a la vez que tiras desde el terminal del altavoz, para ajustar el cable bajo la ranura de sujeción correcta del disco duro.
    • Levanta el altavoz izquierdo y sepáralo del iMac.

    • Si el espacio entre el disco duro y la placa base era demasiado estrecho para que el altavoz pudiera separarse, empuja con cuidado mientras lo separas.

    • Empuja desde el terminal del conector, a la vez que tiras desde el terminal del altavoz, para ajustar el cable bajo la ranura de sujeción correcta del disco duro.

    I found it wasn't necessary to remove the speaker from the left side to remove the hard drive. You can remove the screws, and then slide it over to the left — giving more than enough room to access the hard drive.

    Robert - Contestar

    me too. don't need to remove it if you only want to change the hd

    Alber Einsten -

    Agreed, wast of time to fully remove the speaker.

    Matthew Gonzalez -

    It is difficult to remove the bottom of the speaker because it bends into the frame. Be careful to remove the power button cable, which also routes in a channel in the bottom of the speaker.

    Eric - Contestar

    easier to remove the speakers if you unscrew the front ‘chin strap’ - 6/9 phillips screws that you can see in the picture hold that aluminum piece in place

    flow in - Contestar

  31. Tira hacia arriba en vertical del cable de datos/alimentación SATA para desconectarlo del disco. Tira hacia arriba en vertical del cable de datos/alimentación SATA para desconectarlo del disco.
    • Tira hacia arriba en vertical del cable de datos/alimentación SATA para desconectarlo del disco.

    Is the WD hard drive an Apple Special with some internal rom or other thing? Planning to put in a Seagate Firecuda 2TB. Is there some special plug or temperature sensor requirement? Seems like there is only the SATA connector. Will I encounter fast fans? (can load the software to stop that). Think it’s a swap and is “easy”.

    Carl Schultz - Contestar

  32. Quita dos tornillos T10 de 7.3 mm que sujetan el soporte izquierdo del disco duro a la carcasa trasera.
    • Quita dos tornillos T10 de 7.3 mm que sujetan el soporte izquierdo del disco duro a la carcasa trasera.

    If you have the iMac sitting upright, there is a potential risk of dropping the screws into the iMac casing. Be cautious or lay it down flat.

    Robert - Contestar

    Been there done that. Had to flip it and shake the heck out of it to get that srew to fall out!

    webmail54 - Contestar

    Left hard drive bracket screws are T8!! Had to remove HD first before derouting left speaker cable.

    lamajr - Contestar

    Thank you iFixit for sending a T10 with magnetic tip. You saved me!

    Ben Hannam - Contestar

    The bracket screws are T10. The screws on the left side of the SILVER hard drive itself, are T8. If you seem to need a T8, you are actually trying to remove the wrong two screws. Look immediately to the left of the hard drive & you will see the BLACK bracket frame with two screws that use T10.

    jumpoverpuddles - Contestar

  33. Agarra juntos el disco duro y el soporte izquierdo del disco. Inclina el lado izquierdo hacia arriba de la carcasa trasera, y desliza el montaje a la izquierda. Quita el disco duro y el soporte izquierdo del disco del iMac.
    • Agarra juntos el disco duro y el soporte izquierdo del disco.

    • Inclina el lado izquierdo hacia arriba de la carcasa trasera, y desliza el montaje a la izquierda.

    • Quita el disco duro y el soporte izquierdo del disco del iMac.

    Two notes here:  If you are using OWC’s Thermal Sensor HDD Upgrade Cable, be sure to tuck the cable under the hard drive slightly.  You cannot allow the connector to sit near the top edge since this will not allow the monitor to sit flush with the chassis when it is reattached.  Additionally, the SATA connector does not seem to fit together as snuggly as when it was connect to the HDD, so tape or a plastic cable tie to keep the connection tight may be good insurance to prevent it from coming loose.

    If you are planning on dual booting with Windows 10, the Windows 10 installed failed when the SSD and HDD were both connected at the same time.  I had to disconnect the HDD until Windows 10 was installed.  Note: I did a fresh install on a new SSD not configured as a fusion drive.  If you are planning on doing this as well, use packing tape (or something similar) to hold the monitor in place until after installing the OSs.  Then reconnect the HDD and apply the adhesive to the monitor for a permanent seal.  Good Luck!

    Walter Hayden - Contestar

    Hi Walter, i’m looking to replace the broken fusion drive with a SSD, do i have to get the OWC’s Thermal Sensor HDD Upgrade Cable?

    Gregorio Alvarado Sahli -

    Full removal of the speaker is unnecessary - just very carefully unplug the two-conductor power button cable, which is routed through the groove along the edge of the speaker enclosure. Next, unfasten the two large torx screws holding the speaker enclosure to the chassis. Now you can easily scoot the speaker away from the drive mount - move it over just enough to reach the drive mount’s 2 torx fasteners beneath the edge of the speaker (a CM or two). There’s now enough room to easily remove and replace the drive assembly .

    clinton - Contestar

    Just wondering if the HDD 3.5 (3TB) in my 2015 27’ 5K iMac case are the ones with the temp control firmware onboard. Just got quote from Auhorised repair centre for 2x the normal price of a 3TB drive. They say I can drop in one i source myself if I like but I don’t want to get it back and have the fans run all the time. Thanks in advance :)

    Declan Casey - Contestar

  34. Quita el soporte izquierdo del disco duro. Quita el soporte izquierdo del disco duro.
    • Quita el soporte izquierdo del disco duro.

    This step is unnecessary. Just leave the bracket in place and set the assembly aside.

    Anthony Zimmerman - Contestar

  35. Quita los cuatro postes de tornillo T8 de 8.1 mm del disco duro y transfiérelos al receptáculo de la unidad de reemplazo.
    • Quita los cuatro postes de tornillo T8 de 8.1 mm del disco duro y transfiérelos al receptáculo de la unidad de reemplazo.

    In my case these were T9 screw posts. Late 2012 iMac. They had traces of Loctite on them.

    rsnadd - Contestar

  36. Solo tienes que seguir estos 8 pasos si lo que quieres es sustituir tu disco duro con un kit SSD Suelta la placa frontal de la carcasa empujando sobre la pestaña con tu dedo. Mientras empujas la pestaña hacia adentro, extrae la placa. Separa la placa frontal.
    • Solo tienes que seguir estos 8 pasos si lo que quieres es sustituir tu disco duro con un kit SSD

    • Suelta la placa frontal de la carcasa empujando sobre la pestaña con tu dedo. Mientras empujas la pestaña hacia adentro, extrae la placa.

    • Separa la placa frontal.

    Ich denke die Frontplatte hätte anschliessend auch wieder eingesetzt gehört - bin die Anleitung Schritt für Schritt durch gegangen, und mir ist leider gar nicht aufgefallen, dass dieser Schritt fehlt. Nun ist der iMac bereits wieder verklebt und beim Aufräumen ist mir die übrig gebliebene Frontplatte untergekommen.

    Aber halb so schlimm, die SSD ist angeschraubt, kann sich also eh nicht bewegen.

    Gerhard Dietrichsteiner - Contestar

    My enclosure doesn’t look like this. All I received was a black back plate. Where is the rest of it? Oh boy

    Selwyn Arnold - Contestar

  37. Alinea el conector SATA pequeño para que el lado más corto del conector SSD se ajuste también con el lado corto del conector de la carcasa. Inserta el disco a través de la ranura frontal de la carcasa hasta que el conector SATA esté en su lugar. Solo hay una disposición espacial con la que el SSD se conectará con la carcasa. Si no se alinean bien, gira el SSD y prueba de nuevo.
    • Alinea el conector SATA pequeño para que el lado más corto del conector SSD se ajuste también con el lado corto del conector de la carcasa.

    • Inserta el disco a través de la ranura frontal de la carcasa hasta que el conector SATA esté en su lugar.

    • Solo hay una disposición espacial con la que el SSD se conectará con la carcasa. Si no se alinean bien, gira el SSD y prueba de nuevo.

  38. Alternativamente, podrás colocar los dos tornillos Philips #1 incluidos con el kit de la carcasa para asegurar la sujeción del SSD. Sustituye la placa frontal.
    • Alternativamente, podrás colocar los dos tornillos Philips #1 incluidos con el kit de la carcasa para asegurar la sujeción del SSD.

    • Sustituye la placa frontal.

  39. Conecta el cable SATA con sensor incluido en el puerto de la carcasa. Alinea el lado fino del conector con el lado fino de la carcasa. El cable está diseñado para conectarse al tener una cierta orientación. Si no consigues conectarlo, rótalo 180º y prueba de nuevo.
    • Conecta el cable SATA con sensor incluido en el puerto de la carcasa.

    • Alinea el lado fino del conector con el lado fino de la carcasa. El cable está diseñado para conectarse al tener una cierta orientación. Si no consigues conectarlo, rótalo 180º y prueba de nuevo.

  40. Pela la cobertura adhesiva de la pequeña placa del sensor de temperatura. Pega la placa del sensor de temperatura a una zona metálica expuesta del SSD (lo más cerca posible del conector SATA). Dobla el exceso de cable del sensor de temperatura para que no estorbe mientras terminas de instalar la carcasa.
    • Pela la cobertura adhesiva de la pequeña placa del sensor de temperatura.

    • Pega la placa del sensor de temperatura a una zona metálica expuesta del SSD (lo más cerca posible del conector SATA).

    • Dobla el exceso de cable del sensor de temperatura para que no estorbe mientras terminas de instalar la carcasa.

    Does the small temperature sensor board have to be purchased separately for a 2015 iMac or is there one already attached to the HDD?

    Richard Lee - Contestar

    Hi Richard, our upgrade kit does come with a temperature sensor, but a hard drive bought by itself will not come with one.

    Adam O'Camb -

    The enclosure that came with my kit is all plastic, does the sensor have to be connected to metal? If yes, where would it go given the all-plastic enclosure?

    Lynne Mitchell - Contestar

    Hi Lynne,

    It does not have to be connected to metal. However, the sensor should be stuck on the drive and not on the enclosure so that it can sense the drive’s temperature.

    Arthur Shi -

    My iMac (27-inch, Late 2013) (Model Identifier: iMac14,2) (EMC: 2639), had a Seagate Barracuda 1.0TB HDD installed. There was no temperature sensor on the HDD. I have the Fan Controller that is pictured in this manual on Steps 39, 40 and 41. The photos do not show a small two-conductor cable connected from the Fan Controller circuit board to the logic board. There is usually a cable that connects the small circuit board, where the drive’s temperature is measured, to a connector on the logic board, but not in this iMac. For now, I have installed the Samsung 860 EVO 500GB SSD without a fan controller and it has been running for over two hours without a hint of the fan ramping up. Should I still install the Fan Controller and not worry about connecting the controller sensor to the logic board? Thank you for creating an excellent manual!

    David Higgins - Contestar

    Hello, what if I don’t buy the temperature sensor? Could I break my computer or the SSD? Thank you in advance for your answer.

    kurdonet - Contestar

    You can use Mac Fan Control as a software solution. You won’t break your computer as it will slow down and throttle itself to protect it. More than anything, your SSD will run warmer than usual, which could shorten its lifespan.

    Arthur Shi -

    I just did this procedure with an A1419 (EMC # 2806) and didn’t buy the temperature sensor. I didn’t experience any loud fans afterwards. The machine was originally ordered with 3TB Fusion Drive. After installing the new 2TB SSD (WD Blue WDS200T2B0A) the Disk Utility showed an original 128GB PCI drive in addition to the new SSD. I ignored this PCI SSD and reinstalled OS X on the SATA SSD. All is good here! Oh, also I didn’t use any fancy 3.5” to 2.5” drive adapter, but a simple 3-dollar eBay adapter (can be found with this title, “2.5" to 3.5" Bay SSD Metal Hard Drive HDD Mounting Bracket Adapter”). I keep these laying around just in case. I did have to re-thread the screw holes to re-use the iMac’s HDD screw-posts (used tap & drill set, size 6-32 NC).

    Andy Blakely - Contestar

    I just upgraded my late 2015 iMac with a 1TB Samsung 860 EVO and did not use a sensor. No fan or heat issues over the last week of use. Please note this Samsung drive is not the primary workhorse on the machine as I also upgraded my PCI ssd and use that as the primary drive. I have read on other sites that this model iMac does not need the sensor but I am not 100% on that.

    Chip T - Contestar

    une fois la sonde collé sur le ssd ou est ce que celle ci ce branche ? sur la carte mere ?

    Charly Dewost - Contestar

  41. Inserta las clavijas del disco duro antiguo en los laterales de la carcasa.
    • Inserta las clavijas del disco duro antiguo en los laterales de la carcasa.

    • Los agujeros de la carcasa podrían no estar roscados, y colocar las clavijas podría necesitar algo más de esfuerzo de lo normal. Tómate tu tiempo y hazlo lentamente, asegurándote de que se inserten bien.

    This was an understatement for my drive adapter. The adapter had threads that I believe were M3 threaded whereas the mounting pins are what I believer are 6-32 screws. The mounting pins are not threaded well for self-tapping, so I recommend finding an old screw that used to be used for mounting optical drives into PC cases and using those to thread the holes. You can make sure you have the correct size by screwing the sacrificial screws into the old hard drive where they should fit easily before using them to cut new threads into your 2.5” drive adapter. After that, the mounting pins went into the adapter with very little effort.

    Jakegub - Contestar

  42. Coloca cualquier soporte que hayas separado del disco duro antiguo en la carcasa. Coloca cualquier soporte que hayas separado del disco duro antiguo en la carcasa.
    • Coloca cualquier soporte que hayas separado del disco duro antiguo en la carcasa.

  43. Coloca el cable combo SATA del iMac sobre el cable combo SATA aislante. Distribuye el cableado SATA de forma que no interfiera con otros componentes.
    • Coloca el cable combo SATA del iMac sobre el cable combo SATA aislante.

    • Distribuye el cableado SATA de forma que no interfiera con otros componentes.

    • Intenta que los cables no se doblen demasiado, y procura no colocarlos en espacios demasiado comprimidos.

    How much time after gluing the screen can we use it?

    Maurya Gajjar - Contestar

    A few hours should be fine. I suggest checking the screen after a week and after a month to make sure the adhesive is still fully bonded.

    Arthur Shi -

    Ensure the glass lines up with the edge of the iMac

    After replacing the adhesive strips with new ones and the screen connectors have been reconnected, place the lower edge of the screen on the bottom shelf” to take the weight, but don’t press it back in the shelf too much.

    At this point if you’re careful you still have the ability to ensure the edges of the glass line up with the aluminium edges. As soon as the adhesive strips make contact with the glass you will quickly lose the ability to adjust this to line up.

    pohutukawa - Contestar

    What position should the iMac be in before doing this final comment related to setting the display on the “shelf”?

    joseph sis - Contestar

Conclusión

Para volver a montar tu dispositivo sigue estas instrucciones en orden inverso y usa nuestra iMac Intel Reemplazo de cinta adhesiva para pantalla Retina 5K de 27 " para volver a colocar el cristal de la pantalla.

233 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

80%

¡ VM NachE nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Sam Goldheart

Miembro Desde 18/10/12

420,035 Reputación

547 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

128 Miembros

13,065 Guías creadas

I did successed this. But after just turn on, main fan spins faster than ordinary status. About 1600 rpm. Ordinary rpm is just 1200.

How can I fix it? Not by software solution(i.e., fan control app), help me by hardware solutions, plz.

*Replacement HDD : WDC WD40EZRX-00SPEB0

*iMac (Retina 5K, 27-inch, Late 2014)

*3.5 GHz Intel Core i5

*AMD Radeon R9 M290X 2048 MB

Changwon - Contestar

Dear Changwon, i also own a Retina imac (i7 Radeon 295). Harddisk has been changed by the distributor – they sell customized "Edition iMacs". Now i have the same problem as you subscribed - from day one. Fan speeds up to 1700 / 1750 rpm after a few seconds after power on. Next week my Apple certified distributor will check my iMac and hopefully fix that "noisy" problem. I will inform you, when we will be successful ... Have a great time so long. Greetings, Markus (mr@i-map.de)

Markus -

Did you use a original HDD with apple Firmware or a normal HDD? If u use a nomal HDD with non apple Firmware, you have the Fan Problem.

Klausi -

And it just show 1.8TB but that HDD is 4TB.. :( Help me anybody..

Changwon - Contestar

What does the Festplattendienstprogramm says? Can you see the 4GB there?

Klausi -

So is it possible to replace the harddrive with an SSD drive?

I was surprised to read that the iMac has an SSD and a HDD?

I guess that is how the Fusion Drive works? "In software"?

I thought the Flash would be part of the HDD case and not seperatly on the logic board?

Thorsten - Contestar

same problem , now have dual drives, not the fusion drive. been looking online for the last few days but all of the how to's don't actually help. I can't unmount the GD original drive to fuse them

William Evans -

Anyone know of a GOOD how to on using the terminal to make this a fictional Fusion Drive? I can't get mine to unmount, been trying for 2 days

William Evans - Contestar

I've used this twice to rebuild the core storage and create the Fusion drive::

http://apple.stackexchange.com/questions...

It requires you to wipe/reinstall but its worked fine for me running Yosemite and El Capitan.

John McCarthy -

If your 5k Imac only came with an SSD will the mounting brackets for a standard HDD be available when I open it up?

Cameron Berry - Contestar

I too have this same question. Can I ADD a HD to an iMac Retina if factory configured with SSD? Is the bracket in there? Or the SATA cable? If not, does ifixit sell a kit to do this?

pauljschneider -

+1 on this. Any teardowns of a SSD-only 5K iMac yet?

shaolindave -

I have some good news everyone. i have the late 2015 imac that was purchased ONLY with a 512 SSD WITHOUT fusion drive. i was also wondering the same thing and i can happily report that the new late 2015 iMACs DO HAVE THE BRACKETS IN PLACE. the more challenging piece was to find the custom SATA cable. i was finally able to get one used from powerbookmedic. the apple part number you need is 923-00092. another challenge was finding the hard drive mounting pins that go into the hard drive. After all however i installed a 5tb drive and i am waiting for my thermal sensor to reduce fan speeds. this is great news since i've been trying to find an answer for this myself FOR MONTHS!!

JDoes -

I talked with Apple Forum official Apple store in

Sweden today, and a seller there agreed that it was

possible to do an after sales custom modification

of a newly delivered Retina 27 Imac (512 GB or

1 TB) flash-PCIe-SSD only with (for example) an

additional 2 TB eSATA-SSD - but that this was

likely to cost like twice as much as buying the

additional SSD yourself ... .

So the implication is that a new Retina 27 Imac

with (512 GB or 1 TB) flash-PCIe-SSD as only

storage has a free eSATA-storage slot ... .

Patrik Albin - Contestar

Hi,

I own a late 2015 imac 27" with 1Tb Fusion Drive. I want to replace the HDD by an standard SSD. Do I need to use the owc thermal sensor?

Michael S - Contestar

Anyone knows what's different between normal HDD and this apple HDD? I also want change my 1T HDD with larger ones (2T etc) due to current one was almost full. If changed it does the fan speed become high? Where can I buy apple HDD? Has anyone intalled that OWC In-line Digital Thermal Sensor with normal HDD?

Yao - Contestar

If you are using that much storage, a sensible solution would be a standard massive, HDD in an external caddy connected by Thunderbolt

coplan -

Made the same mistake of going to with the FUSION Drive, the limited SSD compare to the previous version is really noticiable.

I maxed out my ram to 64gb and it felt slower than my macbook Air.

The reason why APPLE charge double is to cover replacement charge of a new display.

Even though I am some techie, I have broken my share of apple display screen. I took it to an certified Apple repair shop for an upgrade on my late

2015 imac, tech must of had issue with step 18-19. Came in for a hard drive replacement, came out with 3 inch grey vertical line.

si bui - Contestar

I can't find where to purchase an Apple Authentic HDD. Additionally, I'd like to put a higher capacity HDD in my iMac anyway.

<p>

At the top of this article, under the parts section, there is an "iMac Intel 27" 5K Late 2014 and Mid 2015 Hard Drive Cable" for $19.95 listed. Does this cable eliminate the high revolution fan problem? Or does one need to use OWC's "In-line Digital Thermal Sensor"?

<p>

Anyone have experience with these cables? Has anyone replaced their HDD with a 2TB or 4TB drive and not had fan problems without getting such a cable?

Steven Bunnell - Contestar

I have the identical question and browsing on this site and other sites couldn' find an answer.

What exactly besides the tools for the replacement I have to have/buy in order to avoid fan issue if I upgrade HDD with "non-Apple" HDD on my 2015 iMac 27 Retina?

Nenad Stankovic -

If you just want to replace a broken screen, do you have to follow all the steps after the original screen is removed?

jujuhay - Contestar

Also I have a mac bought this year - will these instructions be suitable for it? The screen is broken!

jujuhay - Contestar

My screen shows a wide black line. What could it be? Cables or LCD display?

Arcano 17 - Contestar

Hi All.

Can someone pls help clarify the firmware situation for me pls? I have a 27 inch 5K late 2014 iMac and the 3TB fusion drive has failed.

I have managed to determine that the conventional drive is the part at fault and I want to change it, but I am reading about custom firmware's. Is this true? or am I able to just swap out for a new "off the shelf" Western Digital 3TB drive?

If it is true about the firmware how do I get a compatible drive and how do i install the custom firmware.

If I buy an identical drive to the 3TB Seagate drive, Can i just swap over the circuit board from the dead drive? Would that contain the custom firmware?

Thank you for any advise you can offer.

rossfarr - Contestar

I've just successfully finished this. I bought iMac 27" 5K Late 2014 with an SSD, without any HDD / Fusion drive.

First of all, big kudos to the author, I can't imaging doing it without the detailed steps including high resolution images.

As I struggled to find some details when ordering the parts here's for anyone looking for more information:

- Buy all the recommended tools, they are life-savers. Also buy the Adhesive Strips set.

- If you are adding an SSD drive to the SATA bay (Crucial in my case), you won't need the thermal sensor cable. At least I can't see that the fan would be going any high after installing the drive. (I'm on macOS Sierra.)

- If you don't have a HDD in your iMac yet (like me, I only had the PCIe SSD), you will also need the iMac hard drive cable as it is not in. It is the one that they are selling here on iFixit. (I had to order it from elsewhere as it was sold out)

!!! To attach the SATA cable, you will need to disassemble everything including the mother board.

David Zemsky - Contestar

To install the hard drive SATA cable, you will need to follow this (longer) guide: Reemplazo del circuito SSD del iMac Intel 27" Retina 5K Display

One more thing you will need to order: the 4 hard drive pins / screws. Some websites sell them.

David Zemsky -

Are these instructions valid for the 2017 27 inch iMac?

Brandt - Contestar

We don't have guides yet for the 2017 version, but from what I can tell the procedure is very nearly identical. You should be able to perform the swap using this guide and a little extra caution, especially if you have any past experience with iMac repair.

Jeff Suovanen -

Also if replacing the hard drive with a ssd drive are there any cables or enclosure that should be purchased? Trying to put in an evo 850.

Brandt - Contestar

Depends on the iMac you have. For 2017 iMac you dont need any extra cables.

Dennis Sari -

I'd like to replace my drive (I believe it has malfunctioned). What brand/make of drive should I buy to replace it so that it functions as it did prior to the drive failure? I don't want to break the Fusion capability nor the any other functionality. Any thoughts would be appreciated!

Jay Macguyincali - Contestar

I just completed this on a mid-2017 iMac & all went well except for the fact that even though I replaced a Seagate with another Seagate (1TB to 3TB), the fan was constantly on full blast. So, I had to buy the OWC dongle and open up the iMac again to install it. Just completed that & now all seems well, nice & quiet!

Matthew Gonzalez - Contestar

Hi Matthew, can u explain to me what was wrong with a new 3TB (SSD?) hd, and what is it OWC dongle? cheers Tom

Tom Swoboda -

Would like to add one more point. Just completed it today but then the foam tape is no longer sticky enough to hold the screen. I almost broke the screen because of this. So it may be useful to add some double-sided tape on the edges of the case after the operation.

Colin Lai - Contestar

Hi Colin! This is precisely why the guide ends with “To reassemble your device, follow these instructions in reverse and use our adhesive strip replacement guide to reattach the display glass.” You’ll need to get new adhesive, remove the old adhesive, apply the replacement, test the device, and seal it back up! Best of luck!

Sam Goldheart -

Hello all, I know this is quite old but I just replaced the drive to my 27 5k iMac 2014 and I didn’t need the SATA enclosure OR the expensive OWC Temp sensor! I was concerned cuz it was $40 and seemed like a rip-off. I bought a Samsung 860 Evo 1TB and decided to plug it and try it. If it gave me a jet engine fan I’d bite the bullet and buy the sensor. To my surprise fans were fine and I just used double sided 3M tape to tape the drive to the rear casing. So far no issues!

yingwang01 - Contestar

after having reassembled the monitor a white halo appears in the lower left corner, perceptible only when the monitor transmits a black image, from what can it be depended?

giuseppe giordano - Contestar

Probably what I just commented below

Denis Sytmen -

PLEASE NOTE !!!

DO NOT PUSH THE CARDS IN MORE THAN 1CM!!!! IT WILL DAMAGE THE FRAGILE RIBBONS FOR THE LCD.

I did just that, and found my way to the many threads with this issue.

all of which, including myself, needs to cough up $500 for a replacement lcd assembly.

FFS!

Denis Sytmen - Contestar

Thank you for the beautiful guide! Definitely would add the tip in step 21 of grabbing that tab to pull the adhesive strip out.

Everything worked well. Loooooove having an SSD over HD! …and more storage.

Thanks again!

Karl - Contestar

this article mentions an enclosure kit when replacing the hard drive with an SSD, except it does not say where the enclosure kit comes from: is it an additional purchase or does it come with the SSD purchase?

Quentin Karmark - Contestar

Hi Quentin!

The enclosure is an IcyDock 2.5” to 3.5” converter. It is included with the SSD upgrade bundle that’s listed in the parts section.

Arthur Shi -

Thank you Sam very much for the guide. I bought the 1TB SSD replacement kit from Ifixit for my late 2015 iMac after my iMac’s drive gave up the ghost. To the best I can tell, I followed the instructions correctly. When I boot up my iMac I heard the familiar startup jingle but then unfortunately I only get a flashing ? on the screen. I completely uninstalled and reinstalled the SSD drive, again following the instructions, same thing. I can’t find any tutorials that address how to deal with this issue. I can’t afford a new iMac so I’m praying I can get this to work. Any advice greatly appreciated, thank you!

Kaiser Soze - Contestar

In order for anyone to be able to help, I think you’ll need to provide more context. The flashing “?” on the screen means the system cannot find its boot drive.

You said “after my iMac’s drive gave up the ghost”. What does that mean? To me, that implies the drive was dead, and the system wouldn’t boot anyway. It was probably already giving you a flashing “?”. So simply installing a new blank drive wouldn’t change anything.

Did the system boot before, even with a dead drive? If so, how? Did you install an operating system on the new disk before installing it, and it booted off of it before, but does not boot now with a new drive installed?

The more detail you can provide, the more likely it is that someone will be able to understand what the issue might be in your specific case.

Reid Conti -

@ Reid thank you again for responding the other day. Turns out after the SSD installation when I rebooted I didn’t realize I had to “erase” the new drive in order for OS Catalina to load from the Ifixit external drive included in the kit. I emailed Ifixit support and they sent me a link to that tutorial that I didn’t find on my own searching. All good, fully functioning and loving it…like having a better than brand new 2015 iMac now!

Kaiser Soze -

Thank you Reid, I sincerely appreciate your thoughtful response. I’m tied up with work but will return with a more thorough description! (And working on my Surface Pro, sadly not my iMac!)

Kaiser Soze - Contestar

This was a really daunting prospect for me, tearing into a system that seemed utterly inaccessible. Computer repair, either hard or soft is miles from my metier, but this guide and the 2TB SSD replacement kit I got from iFixit made the the process go very smoothly. My iMac was running pretty rough, particularly after upgrading to Catalina, and I decided that since I was going to downgrade back to Mojave anyway, why not replace the 1TB hard drive with an SSD with twice the storage? So glad I did. It is honestly like having a brand new computer. Thanks for the great guide and the all in one replacement kit.

Paul Harrod - Contestar

Success! Replaced a dead fusion drive in our iMac 27” 5K Retina (Late 2015) with a brand new 2TB SSD. One comment after going through this ourselves: you really don’t need to take out the whole speaker. You can just loosen the two screws and move it aside to access the drive/put the new one in. Saves a bit of effort on that step. Otherwise, this was flawless. Thank you so so much for the guide and the link to necessary tools and making it as painless as possible. Couple of notes to anyone reading through these comments for tips: 1) You do NOT need to take out the whole speaker. You can just loosen the two screws and move it aside to access the drive/put the new one in. Saves a ton of effort. Don’t do it! 2) Watch this video: https://vimeo.com/139364064 - it makes it all seem so much less intimidating and I think the video in conjunction with this guide will get you to the right place. Good luck. :)

Melissa Ortiz - Contestar

I have a 2015 imac 5k. It has 32gb or ram with a 1 Tb ssd and it runs mega slow!

The ssd is clean with only the operating system on it. My read/write numbers on Blackmagic are very low ( in the early 200’s)

I know the ssd was installed recently but I do not know if the machine came with a fusion or conventional hard drive.

It did have the noisy, long running fan issue but I did the software hack to correct this.

Does anybody have any idea on how to fix this?

Ken - Contestar

Hi all,

If I need replaced only HD 3TB fusion drive configuration with SSD 2TB what can I use for accomplish this step (copy the content from 3TB old HD drive to 2TB SSD) witch software/tools can I use??

Regards:

Massimo

Massimo Delli Carri - Contestar

I have been reading elsewhere that recent firmware updates means that Apple are now reading SMART data direct from the hard drive, negating the need for the OWC sensor cable. Does anyone have any experience of this?

I’m particularly interested in Late 2015 iMacs.

Copywriter Ben - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 184

Ultimos 7 días: 1,182

Ultimos 30 días: 5,391

Todo El Tiempo: 330,299