Microsoft Surface Laptop 3 13.5" LCD Assembly Replacement

Eric y 4 otros contribuidores

Última actualización: March 4, 2024

1 - 2 horas

Moderado

Atrévete a reparar

Guía aportada por comunidad

Qué necesitas

Partes

Surface Laptop 3 13.5" Screen
Sale price $399.99

Paso 1 LCD Assembly

Microsoft Surface Laptop 3 13.5" LCD Assembly Replacement, LCD Assembly: paso 1, imagen 1 de 1

It's far easier than any other Surface device.

Traducir

Paso 2

From the bottom, carefully pry up the rubber feet on all 4 corners.

Traducir

Paso 3

Using a T5 screwdriver remove the 4 screws on each corner.

Traducir

Paso 4

Make sure the device is completely turned off before proceeding.

Traducir

Paso 5

With the screen open, lift the keyboard out. It doesn't take much force as the part is only held in with magnets once the screws are removed.

Traducir

Paso 6

Invert the keyboard on itself and remove the unshielded keyboard assembly connector.

Traducir

Paso 7

Microsoft Surface Laptop 3 13.5" LCD Assembly Replacement: paso 7, imagen 3 de 3

Remove the clip-on shields for the display assembly.

Traducir

Paso 8

Unclip the connectors. They are pretty tight so I'd suggest using a spudger or 2.

Traducir

Paso 9

Using a T6 screwdriver, remove the 6 screws holding in the display.

Traducir

Paso 10

Lay the display on a heating pad being careful of the connectors. A heat gun would work too.
I used 60 Degrees C for around 15 minutes.

Traducir

Paso 11

Herramienta utilizada en este paso:

Plastic Cards

$2.99

Añadir a la cesta

Use a metal card to get in between the glass and the housing. Swap to a plastic card to cut through the rest of the adhesive.

Traducir

Paso 12

Watch out for the Sensors up the top. If you damage these the device will fail to turn on. It basically bricks completely without the sensors.

Traducir

Paso 13

Heat up the bottom of the display and horizontally pull the screen out. Try to leave the bottom adhesive intact as we are going to be using this later.

Traducir

Paso 14

Microsoft Surface Laptop 3 13.5" LCD Assembly Replacement: paso 14, imagen 3 de 3

Remove one side of the plastic bar holding the cables in place. Slide the display out leaving the plastic bar intact.

Traducir

Paso 15

Screen off. Time to move on.

Traducir

Paso 16

Remove the snap-on shield and cable. We will need this later.

Traducir

Paso 17

CAREFULLY loosen the sensor cable on the back of the display.

Traducir

Paso 18

Microsoft Surface Laptop 3 13.5" LCD Assembly Replacement: paso 18, imagen 3 de 3

Heat the area around the sensors from the front. The adhesive here isn't very strong so you don't need loads of heat.

Traducir

Paso 19

Microsoft Surface Laptop 3 13.5" LCD Assembly Replacement: paso 19, imagen 3 de 3

Remove the old adhesive and make sure it's clean. You really don't want to be removing this screen once it's set down.

Traducir

Paso 20

Install the new adhesive. Remove any large clumps on the bottom. We left the old stuff down there as it's a bit awkward to get to cleaning and reapplying-wise.

Traducir

Paso 21

Test the new screen. Make sure you connect the sensors or it won't start or respond at all.

Traducir

Paso 22

Slide the cable back under the plastic bar and set it back in place. Lightly pull the cables to make sure there's no slack internally.

Traducir

Paso 23

Remove the plastic layer on top of your adhesive and set the screen into the housing. You need to push the screen in quite a bit at the bottom to make it sit correctly.

Traducir