Introducción
Usa esta guía para remplazar una pantalla y digitalizador roto o defectuoso en tu Huawei P30 Pro.
Note: Esta guía te instrucciona como remplazar solo la pantalla dejando el marco original y placa madre en lugar. Sin embargo, algunas pantallas de remplazo para este teléfono vienen preinstaladas con un nuevo marco (chasis), Esto requiere un procedimiento muy diferente. Asegurate que tengas la parte correcta antes de iniciar esta guía.
Abrir el Huawei P30 Pro dañara el sello contra agua en el dispositivo. Si no lo remplazas el sello adhesivo, tu teléfono funcionara normalmente pero perderá su resistencia al agua
Debido al diseño del teléfono, necesitaras remover la batería de ion de lithio en para remover la pantalla.
Reutilizar una batería deformada después de que ha sido removida es un riesgo de seguridad potencial. Remplazala con una nueva batería
Antes de desamblar tu teléfono, descarga la batería menor al 25%. La batería puede incendiarse y/o explotar si perforada accidentalmente, pero las probabilidades de eso son mucho menores si la batería esta descargada.
Necesitaras adhesivo de remplazo para volver a colocar los componentes cuando re-ensamblando el dispositivo.
Qué necesitas
-
-
Antes de comenzar, apaga tu teléfono.
-
Usa un iOpener para aflojar el adhesivo debajo del cristal trasero. Aplica el iOpener durante al menos dos minutos.
-
-
-
Asegura una manija de succión en la parte inferior de la tapa trasera, lo más cerca posible del borde.
-
Levanta la tapa trasera con la ventosa, abriendo un pequeño espacio entre la tapa y el marco.
-
Inserta una púa de apertura en el pequeño espacio.
-
Desliza la púa de apertura en la esquina inferior derecha.
-
-
-
Inserta una tercera púa de apertura en la esquina inferior izquierda.
-
Desliza la punta de la púa de apertura desde la esquina inferior izquierda a lo largo del lateral del teléfono para cortar el adhesivo.
-
Deja la púa de apertura en su lugar en la esquina superior izquierda para evitar que el adhesivo se vuelva a sellar.
-
-
-
Si el adhesivo se vuelve difícil de cortar, lo más probable es que se haya enfriado. Usa tu iOpener para recalentarlo.
-
Inserta una cuarta púa de apertura bajo la esquina superior izquierda de la tapa trasera.
-
Desliza la púa de apertura a lo largo del borde superior del teléfono para cortar el adhesivo.
-
Deja la púa de apertura en la esquina superior derecha para evitar que el adhesivo se vuelva a sellar.
-
-
-
Remueve los diez tornillos Phillips #00 de 4.3 mm de largo.
-
-
-
-
Usa un spudger para levantar y desconectar el conector de la batería
-
-
-
Usa un spudger para levantar y desconectar el conector del cable flexible principal izquierdo de la placa madre.
-
-
-
Usa un spudger para hacer palanca y desconectar el conector del cable flexible principal de la placa hija
-
-
-
Despega la tira adhesiva naranja etiquetada con un 1 de la batería. La cinta adhesiva naranja se rasgará a lo largo de una pequeña línea perforada
-
-
-
Usa un spudger para levantar y desconectar el cable de la pantalla la placa madre
-
-
-
Aplica un iOpener calentado a la pantalla y todas las esquinas de teléfono por al menos dos minutos para debilitar el adhesivo
-
-
-
Cuando la pantalla sea caliente al tacto, aplica una goma de succión en la esquina izquierda del teléfono.
-
Jala la goma de succión hacia arribase inserta una pua de guitarra en la brecha entre el cristal de la pantalla y el marco de plástico.
-
Corta el adhesivo deslizando una pua de guitarra en la esquina superior derecha del teléfono.
-
-
-
Inserta una cuarta pua de guitarra en la esquina inferior derecha del teléfono.
-
Desliza la pua alrededor del borde derecho del teléfono para cortar el adhesivo
-
Si cortar de vuelve muy difícil, recalienta y reaplica el iOpener.
-
-
-
Enhebra el cable de la pantalla a través de la brecha en el marco medio y remueve la pantalla
You forgot to tell us about the ear speaker that was to be removed from the old lcd and stuck onto the new 1
How about the Ear Speaker? Is it glued to to the lcd or chassis?
Can you replace the front glass without replacing the digitizer and LCD
I am not a professional but it didn't seem very possible to me. But even if it is, where can you get the glass only? As far as i've seen it's only sold with the complete LCD screen.
-
Para re-ensamblar tu dispositivo, siga las instrucciones en orden inverso.
Si es posible, enciende tu teléfono y pruébalo antes de aplicar el adhesivo nuevo y sellarlo.
Lleva tus desechos electrónicos a un centro de reciclaje certificado por R2 o e-Stewards
La reparación no salió como planeado? Checa nuestra comunidad de respuestas para ayuda en problemas básicos
Para re-ensamblar tu dispositivo, siga las instrucciones en orden inverso.
Si es posible, enciende tu teléfono y pruébalo antes de aplicar el adhesivo nuevo y sellarlo.
Lleva tus desechos electrónicos a un centro de reciclaje certificado por R2 o e-Stewards
La reparación no salió como planeado? Checa nuestra comunidad de respuestas para ayuda en problemas básicos
Cancelar: No complete esta guía.
28 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Amaury Leonel nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
20 comentarios
Hello just wondering it is easier to replace without a new frame??
Hi elizabethpatrinos,
the screen replacement without replacing the midframe is in general more straight forward and the faster procedure if you’re used to repairs like this. For a display with frame replacement you need to transfer all components of your old phone to your new frame which bears the risk of damaging them. However if your midframe is damaged or bent i strongly advise to replace the screen with the frame. Otherwise your new screen might not mount on your old and damaged frame correctly. At the same time the screen adhesive of the P30 Pro can be a little bit sticky and sometimes it can be hard to get an opening pick between midframe and the screen when only replacing the screen itself. For a beginner i’d advise to replace the screen with frame and to take your time for the repair (take care not to miss any components when transfering them to the new frame and be careful with them), if you feel confident with repairs like this you can replace the screen itself as well and save a little time.
Hi sandeep s,
opening the Huawei P30 Pro will damage the waterproof sealing on the device. If you do not replace the adhesive seals, your phone will function normally but will lose its water-protection.
Hi, could you please tell me which display replacement you used exactly?
I can only find genuine display replacements containing the frame and battery, which is quite expensive. I am searching for a genuine display only replacement part. Can you please help me with that?
Thank you in advance!
So does the use of the suggested 61395 tape negate the lose of water - protection? ie: if done correctly if i use 61395 tape will it retain IP68?
Hi Stephen,
Unfortunately, water resistance is not restored with Tesa tape—the process of restoring guaranteed water resistance requires using special presses and tools.
It is completely wrong guide or the title. It should be named “Huawei P30 Pro Teardown” and nothing apart from that. It stops half way. It doesn’t show how to place the head speaker back and mount the screen. That is most difficult part and it may go wrong.
Hi Dominik, can you please let the readers know what product you used? As described above, nearly all come with frames.
What's about the Fingerprint reader, will it still work after the replacement?
Hi I am not sure if my sons phone has just screen damage or the lcd has gone ? It has like jazzy lines and green white cant see the screen proroerky not sure if I can touch
and looking for someone cheap to fix it? Looking for a original screen
or where can I but it for a p30 pro ?
screeb and digitalizer? Is it
I think the OLED (p30 pro uses it in place of LCD) cable is damaged. So you need to replace the whole screen assembly, that is quite expensive, both for orginal part and aftermarket. my suggestion is to look for a good quality aftermarket one both if you want to keep the OLED or install a cheaper LCD.
In der Anleitung ist ein entscheidender Fehler. Ich möchte nicht sagen alle Modelle der P30 Pro Serie aber zumindest die erst produzierten Modelle haben verschieden lange Schrauben verbaut. Aufgefallen ist mir das bis zum dritten nacheinander erfolglos getauschten OLEDs nicht.
Erst als ich die Nachricht eines Großhändlers genau durch las, stieß ich auf den entscheidenden Satz in dem Stand das Schrauben verbaut werden die Unterschiedlich lang sind.
Ich werde gleich ein weiteres P30 pro OLED tauschen, danach kann ich die entscheidend längeren Schrauben identifizieren und farblich markieren.
Ach ja, die Dichtigkeit kann man ganz einfach mit P7000 Kleber (dick und 100%ig lückenlos aufgetragen) erreichen. Ich habe dies selber mit einem 12 Stunden Test in einer ca. 90 cm großen, gefüllten Regentonne testen können. Auch nach Monaten und weiteren Wasser Bädern ist das Telefon immer noch zu 100% Wasserdicht. Überzeugen konnte ich mich nach einem erneuten Display Schaden vor ca. 2 Wochen. Alle neu von mir angebrachten Feuchte Pads auf den beklebten Schrauben waren pur weis, auch unter dem Mikroskop.