Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Use una moneda para girar el tornillo de bloqueo de la batería 90 grados en el sentido de las agujas del reloj.
-
-
-
Tire de las pestañas de liberación del teclado hacia usted y levante el teclado hasta que se libere.
-
Da la vuelta al teclado, lejos de la pantalla, y recuéstelo boca abajo en el área del trackpad.
-
-
-
Utiliza un alfiler (o lo que quieras) para retirar las tres patas de goma de la carcasa inferior.
-
-
-
-
Hay una ranura en la pared del compartimento de la batería que bloquea la carcasa inferior en su lugar. Utiliza un destornillador plano pequeño para hacer palanca en el borde inferior de la ranura y tira hacia arriba de la carcasa inferior para liberar la ranura de las lengüetas que la sujetan.
-
-
-
Pasa un spudger a lo largo de la costura entre la carcasa inferior y la carcasa superior en la parte frontal del ordenador para liberar las lengüetas que bloquean la carcasa inferior. Tira hacia arriba de la carcasa inferior y continúa utilizando el spudger según sea necesario hasta que oigas tres clics distintos.
-
-
-
Una vez que la parte frontal y los laterales de la carcasa inferior estén libres, gira el ordenador de modo que la parte posterior esté orientada hacia ti y tira de la carcasa inferior hacia arriba y hacia ti hasta que las pestañas posteriores salten (puede ser útil sacudir la carcasa hacia arriba y hacia abajo).
-
-
-
Retira los siguientes 10 tornillos del escudo inferior:
-
Seis Phillips de 3 mm
-
Tres Phillips de 7,5 mm
-
Uno Phillips de 14 mm
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment. (Some models may only have two screws.)
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 11 mm Phillips in the lower right corner. (if present)
-
Four 14.5 mm Phillips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn over the computer and open it.
-
Remove the 2 Phillips screws (3mm) from the edges of the keyboard area.
-
Remove the 4 mm Phillips screw from the lower left corner.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab. Due to model variatons your trackpad connector may be different than the one pictured.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lift the upper case about half of an inch and move it so that you can access the power and speaker cables.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails or a dental pick, carefully pry the connector from its socket. Make sure you're pulling only on the connector and not on the socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully disconnect the multicolored speaker cable from the logic board. As before, make sure you're pulling only on the connector and not on the socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips. (actual screw not present in image)
-
Two 4 mm Phillips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the top shield up from the right side, minding the upper left corner, which may catch on the metal framework.
-
If your iBook has Bluetooth, as discussed in the previous step, you will need to slide the antenna through the lower I-shaped hole in the shield before completely removing the shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer over and disconnect the orange hard drive cable, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four Phillips screws securing the hard drive to the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the hard drive up, carefully guiding the cable through the slot in the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the hard drive brackets from the left and right sides of the hard drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two black T8 Torx screws from either side of the hard drive (four screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the transparent orange loop to disconnect the large orange ribbon cable from the hard drive.
-
Cancelar: No complete esta guía.
156 personas más completaron esta guía.
Documentos Adjuntos
17 comentarios
isit really possible change 320gb hard drive to ibook g4 1.33 14". i heard motherboard doesnt support bigger than 128Gb?
I put one in and now the machine doesn't recognize the drive.
I'm gonna just pull it out and use it as an external until I can figure it out.
Cita de chacal:
isit really possible change 320gb hard drive to ibook g4 1.33 14". i heard motherboard doesnt support bigger than 128Gb?
I just went through the whole process and it worked fine. Used super duper to copy the original drive then restored using target disk mode and my MBP
Make sure that you print out the screw sheet (PDF), and lay out all the screws on the 3 sheets of paper. It makes it easy to keep track of all the screws, and you won't make a mistake when putting every thing back. Also, go slow and take your time. You don't want to rush on the HD replacement. It took me about 2 hours. The hardest part was take the case apart. You may want to look at a youtube video called "iBook G4 Hard Drive Swap", by smalldog.com. The video shows how the case comes apart, and puts your mind at ease when you hear the cracking sounds as the tabs are released. The instructions on the ifixit.com web site were awesome.
Cita de sapugh:
I just went through the whole process and it worked fine. Used super duper to copy the original drive then restored using target disk mode and my MBP
I too installed a 320 gb WD Hard Drive in a iBook G4. No problems. However, I did test the drive with one of my hard drives utilities to make the sure there were no write errors before installing the drive.