Introducción
Sigue está guía para reemplazar el cristal trasero de tu Samsung Galaxy S7 Edge.
Nota: El borde curvo y el fuerte adhesivo hacen que el procedimiento de apertura inicial sea muy desafiante. Se paciente, repite múltiples ciclos de calentamiento y extracción, y el adhesivo seguramente se aflojará.
Qué necesitas
-
-
Calienta un iOpener y aplícalo a lo largo del borde del teléfono durante dos minutos.
-
-
-
Una vez que el panel esté lo suficientemente caliente al tacto, coloca una ventosa lo más cerca posible del borde calentado, evitando la parte curvada.
-
Levanta de la ventosa e inserta un spudger Haldberd o púa de apertura debajo del cristal trasero.
Suction cup does not seem to work.
Makes it sound ridiculously easy, when in reality you have to be pulling with tons of force while also holding the phone down and on top of that you have to insert the pick in a relatively small amount of time.
I was getting no where with the iOpener and picks alone, so I followed a YouTube video and used the iOpener as well as a hairdryer. I had to make the first cut in the ahesive with a utility/razor knife, then as soon as I was through the first part I inserted the plastic picks. The back of the phone has to be too hot to touch, ideally all around, so the iOpener alone is not enough.
Thanks for the above comments. I was also getting nowhere with the iOpener then used a hairdryer on the non-camera end until it was hot to the touch and managed to get a Stanley knife into the gap and lifted enough to get a pick in. Plain sailing from there with patient heating and working the picks in to cut the glue. Eventually success and the back came off.
-
-
-
Una vez que esté firmemente introducida la púa vuelve a calentar y aplicar el iOpener para ablandar el adhesivo.
-
-
-
-
Usa pinzas para despegar cualquier resto de adhesivo del chasis del teléfono. Luego limpia las áreas de adhesión con alcohol isopropílico de alta concentración (al menos 90 %) y un paño sin pelusa para preparar la superficie para el nuevo adhesivo.
-
Despega el adhesivo del nuevo vidrio trasero, alinea con cuidado un borde del vidrio contra el chasis del teléfono y presiona firmemente el vidrio sobre el teléfono.
-
Compara tu nueva pieza de repuesto con la pieza original. Es posible que debas transferir los componentes restantes (como la lente de la cámara) o quitar los respaldos adhesivos de la parte nueva antes de instalarla.
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Compara tu nueva pieza de repuesto con la pieza original. Es posible que debas transferir los componentes restantes (como la lente de la cámara) o quitar los respaldos adhesivos de la parte nueva antes de instalarla.
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
26 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
4 comentarios
this didn’t address the camera lens
They have a separate article for the camera lens.
Is it waterproof with new adhesive film? Isn't it better to use a liquid glue like B-7000 or T-7000?
Ist es wasserdicht mit neuer Klebefolie? Ist es nicht besser, einen flüssigen Kleber wie B-7000 oder T-7000 zu verwenden?
Hi Tobias,
The phone will not be “waterproof” with new adhesive, as that requires a special press. It will be water resistant to a certain degree if you clean the mating surfaces and apply either adhesive or B7000.