Saltar al contenido principal

Introducción

Sigue los pasos de esta guía para reemplazar la placa lógica en tu iPhone 6s Plus.

Es importante tener en cuenta que la placa lógica en tu iPhone y y el sensor de huella digital Touch ID se emparejan en fábrica, por lo que reemplazar la placa lógica desactivará Touch ID a menos que también instalará un botón de inicio de reemplazo que se haya emparejado correctamente con tu placa lógica nueva.

También puedes usar esta guía para reemplazar las partes siguientes:

  1. Antes de desarmar su iPhone, descarga la batería por debajo del 25%. Una batería de litio-ion cargada puede incendiarse y / o explotar si se pincha accidentalmente.
    • Antes de desarmar su iPhone, descarga la batería por debajo del 25%. Una batería de litio-ion cargada puede incendiarse y / o explotar si se pincha accidentalmente.

    • Apaga su iPhone antes de comenzar el desensamblaje.

    • Retira los dos tornillos Pentalobe de 3.4 mm a ambos lados del puerto Lightning.

    Make sure you use the correct screw driver tip to remove these screws, which for the iPhone 6s Plus is the P2, otherwise you may strip the tip of the screw making it 10 times harder to remove. If once the screw is lose, it will not come off, use a magnet to remove it.

    Miguel Perez - Contestar

    If I do it by myself, will it damage the water resistant strip?

    I know iphone 7 have it ,but I am not sure 6s plus have it.

    Ganqian Zhu - Contestar

    iPhone 6s has an adhesive gasket under the display, similar to the iPhone 7—however, it doesn’t add much in the way of waterproofing since the 6s has non-sealed openings in other parts of the phone. Water resistance on the 6s is primarily internal (seals around the logic board connectors, etc.). It may still be worthwhile to replace the adhesive on the 6s in order to help keep the display firmly seated so it doesn’t move/wobble at all under pressure, but the phone will continue to work fine whether you replace the adhesive or not.

    Jeff Suovanen -

    Salve nella procedura iniziale di smontaggio display con la ventosa non è menzionato il fatto di scaldare i lati del display per “ammorbidire” la striscia che incolla il display alla scocca.

    Non è necessaria la cosa o è consigliabile ?

    grazie

    Hello, in the initial disassembling procedure with the suction cup, it is not mentioned how to heat the sides of the display to "soften" the strip that glues the display to the body.

    Is not the thing necessary or is it advisable?

    thank you

    Daniele - Contestar

    You’ve probably received your answer by now but for future enquirers, it does help the process of taking the screen off if heat is applied to the screen. If you have a hair Dryer use that on a low setting to heat the edges of the screen until it’s almost too hot to touch then slip very thin metal spudger around the edge to cut the adhesive. The carefully lift the screen with the help of the spudger and continue with your repair

    Cheers Wayne

    Wayne Lyell -

    How do I know that the Battery has ZERO Charging Cycles on it when it arrives ? Is there a (downside) to Higher Capacity batteries ? It is INCREDIBLY DIFFICULT to maintain a “Zero Chinese Products Lifestyle”, so how do I know that I’m not getting a deficient Chinese battery, potentially a refurb. battery ?

    integritybuilders - Contestar

    When your repair is complete, you can use coconutBattery to check your new battery stats and cycle count. (A properly tested battery may already have a charge cycle or two on it.) Avoid higher capacity batteries on iPhones—they’re generally either gimmicks, unsafe, or both. As far as the quality of the part, that comes down to how much you trust your supplier and whether they guarantee the product.

    Jeff Suovanen -

    So I need to empty the battery to zero percent?

    johnpatrickanat - Contestar

    Below 25%, exactly as stated in the instructions. There’s no benefit to draining it further than that, and in fact you’ll slightly shorten the service life of the battery by draining it all the way to zero. Follow the instructions exactly as written—if you go off-script, you’re a lot more likely to break something.

    Jeff Suovanen -

    So my screen shattered completely and the screen first had colored lines on tge while right side then it went out completely. If i get an lcd and digitizer replacement I'd that oing to fix it

    shellietheleo - Contestar

    I would initially recommend a well-lit, comfortable area and placing the screws on a white piece of paper with the screw sizes written down (apparently there are magnetic mats, also). Also, I found placing the phone on a paper towel is good so that if a screw is dropped, it will lessen the likelihood of bouncing away.

    Lou Fazio - Contestar

  2. Opcionalmente, calienta levemente el borde inferior del iPhone utilizando un iOpener o un secador de pelo durante más o menos un minuto.
    • Opcionalmente, calienta levemente el borde inferior del iPhone utilizando un iOpener o un secador de pelo durante más o menos un minuto.

    • El calor ablanda el adhesivo que mantiene asegurada la pantalla, haciendo que sea más fácil de abrir.

    This is important. I’ve serviced a lot of iphones/ipads for my family as a hobby in the past.

    The adhesive was so tight, I cracked the screen trying to pull it/pry it off.

    I highly suggest heating at least the bottom edge enough to soften the adhesive

    garbage911garbage - Contestar

    I didn’t have an iOpener, nor a heat gun; however I do have a small personal size hand pillow filled with feed corn. Two minutes in the nuke machine got it plenty warm, and smelled like fresh popcorn too.

    bradiac - Contestar

    A hairdryer would work also to replace the iOpener

    Jaron Foo - Contestar

    I would suggest that you are not shy with the hairdryer. A high heat on the bottom of the phone for at least a minute, if not more, if required.

    Mark Taberham - Contestar

  3. Al abrir la pantalla en el 6s Plus, se separa una delgada tira de adhesivo alrededor del perímetro de la pantalla. Si prefieres reemplazar el adhesivo, ten listo un conjunto de nuevas tiras adhesivas antes de continuar. Es posible completar la reparación sin reemplazar el adhesivo, y probablemente no notarás ninguna diferencia en la funcionalidad.
    • Al abrir la pantalla en el 6s Plus, se separa una delgada tira de adhesivo alrededor del perímetro de la pantalla. Si prefieres reemplazar el adhesivo, ten listo un conjunto de nuevas tiras adhesivas antes de continuar. Es posible completar la reparación sin reemplazar el adhesivo, y probablemente no notarás ninguna diferencia en la funcionalidad.

    • Aplica una ventosa en la esquina izquierda inferior del ensamblaje de pantalla.

    • Si tu pantalla esta muy quebrada, cubriéndola con cinta transparente puede hacer que la ventosa se adhiera. Alternativamente, una cinta muy fuerte puede ser usada en lugar de la ventosa. Si todo lo demás falla puedes pegar la ventosa a la pantalla rota.

    take out screws first!!

    Yoav Karmon - Contestar

    Make sure you use the right screw driver tip for i phone 6s Plus, which is the P-2. If the screw will not come off once is lose, try using a magnet.

    Miguel Perez - Contestar

    My cracked screen prevented the suction cup from sealing. SOLUTION: With a piece of clear packing tape across the screen, the suction cup will seal and pull.

    Jim Cowles - Contestar

    I broke my iphone screen in the first step!

    Pierre Bertram - Contestar

    This screen removal step got more wrestley than I anticipated. The adhesive is quite strong. I used a flat-ended razor tool that I have to begin the prying - I don’t know how I would have got it started without this.

    Lou Fazio - Contestar

    Ok - just got my battery replacement kit and even got the opening kit for added insurance just in case. Settled down to startwork after carefully cleaning my (immaculate) screen - no scratches or anything, with rubbing alcohol, removing screws and warming with a hair dryer, only to find the suction cup provided in the kit is worse than useless! It won’t stick to the screen well at all. When it does - it pops off at the lightest pull :-( Now what do I do to get this started?!

    CoffeeCup - Contestar

  4. Tira de la ventosa con una presión firme y constante para crear un ligero espacio entre el panel frontal y la caja posterior. Tirar demasiado fuerte puede dañar el ensamblaje de la pantalla. Aplica la presión necesaria para crear un pequeño espacio entre el ensamblaje de la pantalla y la caja posterior.
    • Tira de la ventosa con una presión firme y constante para crear un ligero espacio entre el panel frontal y la caja posterior.

    • Tirar demasiado fuerte puede dañar el ensamblaje de la pantalla. Aplica la presión necesaria para crear un pequeño espacio entre el ensamblaje de la pantalla y la caja posterior.

    I had a shattered front glass panel so I could not get the suction cup to seal properly. I tried a couple of different ways to get good suction but to no avail. I eventually used a Stanley knife to pry up the corner so I could get the spudger into the opening.

    John Architzel - Contestar

    A really high quality packing tape over the entire screen will usually be enough to use the suction cup on a shattered screen.

    djwooten -

    I used a suction cup on each side to provide counter traction. I braced the iphone between my knees and pulled apart while my helper inserted the spudger

    jkanne - Contestar

    This was by FAR the most difficult part of this whole thing. I confess the spudger was not cutting it so I used a butter knife to get into the small opening first, then used the spudger to go around the screen.

    Julie Sanchez - Contestar

    Hey everyone, if you never have done this part before be aware there is an extremely strong adhesive around the lip of the screen and once again is extremely strong. I had to get a friend to insert the pry/pick into the small gap while I used one hand to brace the phone down and the other to pull the suction cup without it digging into my hand. Go slow, it took me 5 tries because I didn’t realize how strong the adhesive was.

    bartmistrot - Contestar

    I also had a badly cracked lower screen - that glass was actually threatening to pull off the phone in chunks during this step, even with packing tape. Resorted to @j2arch’s tip and inserted a utility knife vertically into the seam between the display and phone body. Was able to lever the glass enough to get the spudger in there.

    Jason Augustyn - Contestar

    I have replaced sevrel screens for my sister in law and my niece. The packing tape has worked every time and that’s with it Shattered and pieces already falling out. You have to make sure the packing tape goes to the edge of the screen but doesn’t touch the frame. I have the plier like screen remover and use that it is much easier to remove the screen by your self with that tool. I also have the little finger suction cup that comes with the kit here. I bought the plier suction cup tool When I had to replace the screen that had the pieces of the screen missing and I don’t regret spending the extra money for that it has made a world of difference. I do this as a hobby it’s not a job for me. The electric divide repair kit from Lowe’s is also a very good kit to help. If you’re only going to do it once the kit that comes with the package is a great deal from ifixit. Well worth the money to spend the little extra to get the kit if you all ready don’t have the tools.

    Brent - Contestar

    If you try to use the spunger near the home button and try to pry it can crack your screen. This happened to me.

    Jeffrey - Contestar

    Same thing happened to me. This should be a big warning in these steps. If you have a small to moderate crack in you screen, but you weren’t planning on replacing the screen at the same time as another repair inside, there’s a risk of damaging the screen further and making it inoperable.

    DW7ACCT -

    I found it easiest to use two suction cups. One on the front as directed, and a second one on the back. Give the spudger to your assistant, and have them slip it in place while you pull the display from the case.

    gordojenkins - Contestar

    I gave up with the suction cup as it wasn't working for me with a cracked screen. Having heated the bottom of the phone with a hair dryer with a high heat for a good minute or so, I used a safety scraper (essentially a razor blade in a holder) along the bottom of the phone to separate the screen from the body of the phone. I used the scraper vertically between the bottom of the screen and the phone body and levered it sufficiently so that I could fit the spudger between the screen and the phone body. My experience when I first used the spudger around the frame was that the cracks in the screen caused the screen glass to separate from the frame, so I had to re-do it and ensure that the screen frame was separated from the phone body.

    Safety scraper:

    https://www.amazon.co.uk/Unger-CD170-Win...

    Mark Taberham - Contestar

  5. El lugar más seguro para hacer palanca es la muesca en el panel frontal sobre la toma de auriculares. Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares. Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares.
    • El lugar más seguro para hacer palanca es la muesca en el panel frontal sobre la toma de auriculares.

    • Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares.

    This was by far the hardest part of the repair for me. Getting leverage while finding a way to prod with a spudger is a challenge in coordination. I used a second spudger with point holding the phone down by the headphone jack, with the other end of the spudger anchored to my desk.

    drpotter - Contestar

    When warmed, the suction cup was useless. Using the tip of a knife blade, was able to get it separated enough to insert spudger.

    hutland - Contestar

    For me this was the most time consuming task. I used a hair dryer for heating. I found a very tight adhesive. For a moment I thought of abandoning my efforts and take the assembly to a professional repairman. But as they say, patience is a virtue.

    After fiddling for about 20 minutes, I achieved a barely noticable opening. So I decided to change the strategy. Instead of applying heat all over the base, I preceeded with small steps with heat concentrated near the opening. I applied intense heat only for about 15 to 20 seconds and immediately working with spudger. It took about an hour to completely open the case. It worked.

    Thanks for reading.

    - Mr Gamma

    Gamma Pailvan - Contestar

  6. Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera. Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera.
    • Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera.

    just changed the screen, but due to the tape along side the screen , it is best to heat a little so the glue losses and you can get the screen off better, like indicated

    Bart Blanckaert - Contestar

  7. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla.
    • Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla.

  8. Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior. Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior.
    • Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior.

  9. Inserta la punta plana del spudger debajo del borde derecho de la pantalla. Desliza el spudger por el lado derecho.
    • Inserta la punta plana del spudger debajo del borde derecho de la pantalla.

    • Desliza el spudger por el lado derecho.

  10. Usa una herramienta de apertura de plástico para mantener presionada la caja trasera mientras levantas la ventosa para abrir el teléfono. No retires la pantalla por completo o dañarás los cables de datos que la conectan cerca del borde superior del iPhone.
    • Usa una herramienta de apertura de plástico para mantener presionada la caja trasera mientras levantas la ventosa para abrir el teléfono.

    • No retires la pantalla por completo o dañarás los cables de datos que la conectan cerca del borde superior del iPhone.

  11. Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla. Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla.
    • Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla.

    Remember to apply the screen gasket on the re-assemble. The gasket is provided in the kit but not mentioned here on the instructions.

    Won Hong - Contestar

    There’s a link to the entire gasket replacement procedure in Step 21.

    Jeff Suovanen -

  12. Sujeta suavemente el ensamblaje de la pantalla y levántalo para abrir el teléfono, utilizando los clips en la parte superior del panel frontal como bisagra. Abre la pantalla aproximadamente a un ángulo de 90º, e inclínala contra algo para mantenerla apoyada mientras estás trabajando en el teléfono. No abras la pantalla más de 90º; aún está conectada a la parte superior del teléfono por medio de la pantalla, el digitalizador y los cables de la cámara frontal, que pueden romperse fácilmente.
    • Sujeta suavemente el ensamblaje de la pantalla y levántalo para abrir el teléfono, utilizando los clips en la parte superior del panel frontal como bisagra.

    • Abre la pantalla aproximadamente a un ángulo de 90º, e inclínala contra algo para mantenerla apoyada mientras estás trabajando en el teléfono.

    • No abras la pantalla más de 90º; aún está conectada a la parte superior del teléfono por medio de la pantalla, el digitalizador y los cables de la cámara frontal, que pueden romperse fácilmente.

    • Agrega una banda elástica para mantener la pantalla en su lugar mientras trabajas. Esto evita una tensión excesiva en los cables de la pantalla.

    • En caso de necesidad, puedes utilizar una bebida enlatada sin abrir para apoyar la pantalla.

    if the display cables are damaged how can you tell ?

    Smiley McSmilebot - Contestar

    In theory, I like the idea of propping up the screen with a rubber band and box/soda can like this, but after ripping the FaceTime camera cable twice, I realize that this method puts too much stress on the cable because it places the screen so far back. Even in this photo, you can see that the cable is taut. I’d recommend just holding the screen with your free hand to put the least amount of stress on that cable as possible.

    Ben Estabrook - Contestar

  13. Remueve los dos tornillos Phillips que sujetan el soporte de conector de batería a la placa lógica:
    • Remueve los dos tornillos Phillips que sujetan el soporte de conector de batería a la placa lógica:

    • Un tornillo de 2.9 mm

    • Un tornillo de 2.3 mm

    • A lo largo de esta guía, mantén un registro cuidadoso de tus tornillos para que cada uno vuelva a su lugar durante el re-ensamblaje Instalar un tornillo en el lugar equivocado puede causar daños permanentes.

    FYI - I used some blue painters tape wrapped around a piece of cardboard to hold the screws and brackets in place, in order, so they did not get lost. Some of those screws are MICROSCOPIC so be careful!

    I also suggest having very good lighting, even a camping headlight for hands-free well lit work space. You will thank me later :-)

    Julie Sanchez - Contestar

    Use the bit labeled “PH000”.

    Joe Teichert - Contestar

    PH000 bit just wants to free-spin in the 2.3 mm screw. no bite in the head at all. had no difficulty removing the 2.9 mm screw with the same Phillips. had to abandon battery replacement effort.

    Benjamin Stalcup - Contestar

    For this part, neither PH000 or Y000 worked. Technically, it’ll set you back 31$ because you will need the PH00 screwdriver for this part, and the part where you need to open the screen. They have ph00 screwdrivers in every hardware store and even ifixit.com. just know that they put the wrong screwheads for you

    Jack Daniel - Contestar

    Do not lose track of which hole these screws go into. They MUST be put back into the correct hole that they came out of. If not, you will get the dreaded “long screw damage” on the mainboard, and that will be the end of the show.

    Just remember where these screws go, and it will be fine.

    Harry McDow - Contestar

    This step is extremely important in fixing your phone: I had an iPhone that I fried as I forgot to disconnect the battery, end of the show!

    Jaron Foo - Contestar

    Ended up employing a Philips #0 from a regular jeweler/precision kit on the 2.3mm screw. Bits seem a bit off for this step.

    Vance Bell - Contestar

  14. Remueve el soporte de conector de batería. Remueve el soporte de conector de batería.
    • Remueve el soporte de conector de batería.

    Does it matter if the brackets arent put back in the phone? I bought a used phone and brackets are missing. Thanks!

    Coupon Crazy - Contestar

    Auch die Abdeckung ist angeklebt. Also mit etwas Vorsicht und Geduld rangehen.

    eckhardd@icloud.com - Contestar

    If you have forgotten your High School German -

    The cover is also glued. So take some care and patience.

    Glen Paetz -

    My bracket actually has a black wire connected on the underside that is attached to the metal bracket (with screw) below it in the picture. I decided to leave it on and just move it to the side.

    Victor Ng-Thow-Hing - Contestar

  15. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica.
    • Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica.

  16. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él.
    • Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él.

    When putting the new battery in, make sure to line up the plug and not to the top of the battery… our battery was smaller so the plug would NOT have lined up if we used the top of the battery. ALSO, the plug was NOT 90 degrees so we had to finagle the plug. Also, make sure there is a clear CLICK when you plug in the connector or it may not work. Ours went in but guess didn’t go far enough so we had to take the screen off and push it harder until we heard the “click” then it worked fine.

    Won Hong - Contestar

  17. Remueve los siguientes tornillos Phillips :
    • Remueve los siguientes tornillos Phillips :

    • Tres tornillos de 1.3 mm

    • Un tornillo de 1.6 mm

    • Un tornillo de 3.0 mm

    • Durante el reensamblaje, es fundamental colocar este tornillo de 3.0 mm en la esquina superior derecha del soporte. Colocarlo en otro lugar puede dañar la placa lógica.

    I really don't see value in removing screen use box and rubber band keep at 90 degrees.

    John Parker - Contestar

    I leave screen on as well for this. - Tho I prefer a 45 degree lean.

    Thor -

    I just changed my battery and also left the screen attached. I was lucky enough to get all 3 adhesive battery strips out clean so I didn’t have a struggle with the battery coming out. If I was going to need to get rough with it I was going to take the screen off at that point.

    Michael Gross - Contestar

    To keep track of screws, draw a quick outline of the display cable bracket/cover, with five dots where screws should be. Drop the screws on the corresponding dot. Helps if you use magnet pad.

    Christa - Contestar

    Better yet, print out the pictures from the iFixit website, and use clear tape (“Scotch tape”) to TAPE the screws onto the place in the picture where they belong.

    Tom -

    Which screwdriver from the kit do I use for which screw?

    Shiva Sharma - Contestar

    I made a mistake and unscrewed the screw just north north west of the one circled in yellow. Of course I lost the screw. Can anyone give me any guidance about this? what does the wire connected to it do? What is the size of the screw, in case I have to replace it?

    P.S. This is another reason to consider the possibility of NOT removing the screen just to replace the battery: removing the screen presents a additional possible headache, especially for people like me with bad eyesight who probably shouldn’t be doing this in the first place.

    Tom - Contestar

    I didn’t think this was necessary, bit I see it relieves stress on the front-facing camera and sensor cable connector; I did not disconnect the display connector nor remove the display screen.

    Lou Fazio - Contestar

    I second this finding. I too did not remove the screws nor the bracket. The cables look a bit stretched, but certainly not strained.

    -Gamma

    Gamma Pailvan -

    This step of separating the two parts of the phone deserves careful consideration. In my case, I had propped up the display assembly with a box and rubber bands. However, only 2 of the battery adhesive strips came off easily. The effort to remove the battery with the display assembly attached was not a good move on my part. I jarred the ear speaker cable and after reassembly I had no camera or working ear speaker. Taking off these 5 screws and removing the three cables is not difficult. My suggestion: is you have ANY trouble removing the 3 battery adhesive strips, STOP, separate the two components, and then continue with the battery removal. Don’t struggle removing the battery with the display assembly attached. (I replaced the ear speaker cable, and all is working now)

    Richard Perl - Contestar

    Thanks for this tip! I am having a really hard time removing this plate because one of the screw heads are stripped. So I’ll try removing the battery adhesive strips first to see if I can get the battery out without removing the screen.

    nathanfunk -

    Use dixie cups and label them for each part you take out. You can stack the dixie cups to keep them in order.

    Bradley Nolen - Contestar

    I skipped this for the battery removal, but when I went to replace the seal, I had to remove it anyway.

    dgol69 - Contestar

    I lost the bottom left screw of the five in this step - anyone know if it’sgoing to cause a problem? ‘m going to go ahead and put thephone back together anyway - wil report back withresult

    CoffeeCup - Contestar

    OMG…. SO excited! It works! Seems that missing screw wasn’t an issue. The reason I’m so excited is, I’m a senior and have bever attempted anything like this before and was worried I’d mess it up, or it just wouuldn’t work for whatever reason. I know I never would have tried if it weren’t for finding this site, the great service, parts to do it and the videos/guides. Thank you so much ifixit. :-)

    CoffeeCup - Contestar

  18. Remueve el soporte del cable de pantalla. Remueve el soporte del cable de pantalla.
    • Remueve el soporte del cable de pantalla.

    Be careful on this step: with my iPhone, one of the connectors (the home button/fingerprint sensor) was stuck to the underside of the bracket and I almost strained its cable.

    kevin - Contestar

  19. Ten cuidado de solo levantar el conector y no el zócalo de la placa lógica. Usa una herramienta de apertura de plástico para desconectar la cámara frontal y el conector del cable del sensor.
    • Ten cuidado de solo levantar el conector y no el zócalo de la placa lógica.

    • Usa una herramienta de apertura de plástico para desconectar la cámara frontal y el conector del cable del sensor.

    FYI, in the video she uses the spudger for this but I think either one will work.

    Julie Sanchez - Contestar

    I found prying from the right to be better

    Lou Fazio - Contestar

    Is there any need for this step if only the Battery is replaced

    mrrreid - Contestar

    I don’t recommend using the spudger for this as you can do more damage that way. I scratched the black square thing underneath.

    Laura Houghton - Contestar

    I managed to remove the battery without disconnecting and removing the display first. This avoids possible difficulties in these steps (see below).

    One has to be careful that, while fighting with the battery strips, the display remains in its 90º position

    alfasw33 - Contestar

  20. Usa una herramienta de apertura de plástico para desconectar el cable del digitalizador y  sacarlo de su zócalo en la placa lógica Cuando vuelvas a conectar el cable del digitalizador, no presiones el centro del conector. Presiona un extremo del conector, luego presiona el extremo opuesto. Presionar en el centro del conector puede doblar el componente y causar daños al digitalizador.
    • Usa una herramienta de apertura de plástico para desconectar el cable del digitalizador y sacarlo de su zócalo en la placa lógica

    • Cuando vuelvas a conectar el cable del digitalizador, no presiones el centro del conector. Presiona un extremo del conector, luego presiona el extremo opuesto. Presionar en el centro del conector puede doblar el componente y causar daños al digitalizador.

    Thanks you i fix it

    God Hand - Contestar

    “When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage. “

    The following note above was so helpful. I was speeding through the process of getting things back together, since it seemed easy to connect the digitizer cable, but I kept pushing it in the middle and I wouldn’t connect. Until I read through this step and realized it was easier if I would’ve connected one side and then the opposite side right after.

    Jeffrey Robinos - Contestar

    Don’t be too shy when pushing the ends of the digitizer connector back to place. If it does not connect properly, you might face the “half backlight” problem, even if you did not kill any LCD filter. Also check carefully, that you don’t clamp parts of the sticky sealing material placed around the connector inside the connection area.

    Norbert Andreas Richartz - Contestar

    This part was a very frustrating experience for me.  I thought that my replacement screen was just poor quality, as it worked when it wanted to work.  Pressing home/power repeatedly sometimes brought it back, charging to 100% also brought it back.    The actual problem was that it is very easy to get some of the gasket material caught in the connector, which I couldn’t see until I used my jeweler's loupe.  I used 91% alcohol to carefully clean all of this off until all pins were shiny, and it took about 6 tries to get it right.  However, the screen’s been running well for 2 days now.  I already bought another screen replacement which I have for a spare as it was 100% not the problem.

    chumblyf - Contestar

    I followed all the steps, so the sound is missed. What could be happened? thanks a lot. Fabio Balbino

    Fabio Balbino - Contestar

  21. Asegúrate de que la batería está desconectada antes de desconectar o reconectar el cable en este paso. Desconecta el cable botón home/lector de huellas alzándolo hacia arriba del zocalo en la placa lógica.
    • Asegúrate de que la batería está desconectada antes de desconectar o reconectar el cable en este paso.

    • Desconecta el cable botón home/lector de huellas alzándolo hacia arriba del zocalo en la placa lógica.

    How much is this to replace?

    Alistair knight - Contestar

    And where could I buy from?

    Alistair knight - Contestar

    After finishing the assembly I got the message “Touch ID cannot be enabled on this phone”. I found this connector was loose. Plugged it back in and that fixed it.

    Bryan Province - Contestar

    Thanks for the tip. Same thing happened to me, some leftover adhesive was in the way!

    Lua Tech -

    Always make sure to disconnect the battery before you do any work on the phone replacing any parts the digitizer or anything. And before you start make sure the phone is turned off you don’t want any power surges. If you also have a static electricity bracelet that also is a plus to use but isn’t a necessity just a nice piece of mind. Some cases you do need to use one so you don’t discharge static electricity to an electrical component and mess it up.

    Brent - Contestar

    Be very careful in this step. I noticed it’s very easy to tear the flex when trying to lift it out of its socket from the right side.

    shoeib - Contestar

    What is the cable and how is it connected/fixed to the motherboard between the bottom socket and the screw hole.

    Mine came loose somehow?

    Jason Engelsman - Contestar

    I figured out my own question its the Wi-Fi diversity antenna cable. But how is it connected/secured to the motherboard?

    Jason Engelsman - Contestar

    i pressed on the center of the digitizer connection. and the bottom half of my screen didnt work. i then took that same front panel assembly and tried to install it on another old iphone 6s+ and i had the same issue.

    can i still fix it?

    what exactly is broken now?

    alejandro rueda - Contestar

    @mynameisoli Honestly this just sounds like a defective screen to me, but it’s hard to say for sure. Look closely at the connector at the end of the ribbon cable and check it for damage. If it’s slightly bent/curved, all the pins won’t make good contact in the socket. You can try bending it back so it lays flat, but you have to be very careful not to damage the connector or contaminate the pins with skin oils, so it’s tricky—and it may be harder to return as “defective” if you mess up the connector. So try this at your own risk. Apart from that, I would just return it and try a different display. Good luck!

    Jeff Suovanen -

    The 6s plus screen repair kit i bought has the wrong size cable here on the replacement part. SOL.

    Alex Richardson - Contestar

    Once I accidentally disconnected the display assembly cables before disconnecting the battery. Now the home button and fingerprint sensor doesn’t work. Any solution to this?? I have tried a different home button, even that doesn’t work.

    a3roar - Contestar

    I changed the battery on my iPhone and put all together again and charged it. When I pressed the home button the lock screen with my picture appeared and when I pressed it again the screen with the digits from 0 to 9 appeared. I was asked to enter my passcode, but when I did that nothing happened, the phone did not open.

    What could be wrong? Is the home screen cable not fully connected or what could be the reason for this?

    THORDUR JOHANNESSON - Contestar

  22. Remueva el ensamblaje de pantalla. Durante el reensamblaje, deténte aquí si deseas para reemplazar el adhesivo  alrededor de los bordes de pantalla.

    For instructions on home button swap out to the new screen you just installed, go here

    Reemplazo del ensamblaje del botón de inicio del iPhone 6s Plus

    Superior Office Systems - Contestar

    Do you know whether the adhesive contributes to waterproofing, or just for stability/adhesion?

    Christa - Contestar

    @kitabel The iPhone 6s case isn’t waterproof, so I don’t think adhesive around the display is contributing anything other than stability. The 6s series does have some water resistance, but it’s mostly internal and not something Apple advertises.

    Jeff Suovanen -

    If you have a replacement adhesive for the display, you may need to install it before reconnecting cables to the components. If the adhesive wraps all the way around the display, it will be impossible to install it once the display is reconnected.

    Matthew Olwell - Contestar

    These instructions worked great for me. Thank you!

    Chris Enloe - Contestar

  23. Despega cualquier cinta que cubra los tornillos del soporte de la cámara iSight Despega cualquier cinta que cubra los tornillos del soporte de la cámara iSight Despega cualquier cinta que cubra los tornillos del soporte de la cámara iSight
    • Despega cualquier cinta que cubra los tornillos del soporte de la cámara iSight

    If like me you are only wanting to clean out the speaker, you do not need to do this step. You can skip to step 50

    Brad “Bradster48” Mason - Contestar

    Mine had no tape there

    Gustavo Delfino - Contestar

  24. Remueve los siguientes tornillos Phillips del soporte de cámara:
    • Remueve los siguientes tornillos Phillips del soporte de cámara:

    • Un tornillo de 1.9 mm

    • Un tornillo de 2.4 mm

  25. Remueve el soporte de la cámara iSight. Remueve el soporte de la cámara iSight.
    • Remueve el soporte de la cámara iSight.

    When replacing the bracket be sure to get the other end of the NFC bracket included with the right hand screw.

    Thomas Hayes - Contestar

  26. Desconecta el conector de cámara iSight de su zócalo en la placa lógica. Asegúrate de levantar solo el conector y no el zócalo en la placa lógica.
    • Desconecta el conector de cámara iSight de su zócalo en la placa lógica.

    • Asegúrate de levantar solo el conector y no el zócalo en la placa lógica.

    If necessary, the sticky patch on top f the connector should be removed. Helped my case a lot :)

    Alexander Leuschner - Contestar

  27. Inserta el extremo plano del spudger entre la cámara iSight y la caja trasera. Con cuidado levanta la cámara de su zócalo.
    • Inserta el extremo plano del spudger entre la cámara iSight y la caja trasera.

    • Con cuidado levanta la cámara de su zócalo.

  28. Remueve la cámara iSight. Remueve la cámara iSight.
    • Remueve la cámara iSight.

    Hi ,

    Thanks a lot for your tutorial !

    Can you explain how can we change the lens of the camera ?

    Thanks ;)

    rocofolie - Contestar

  29. Inserta una herramienta de expulsión de SIM en el orificio de la bandeja SIM. Presiona para expulsar la bandeja SIM.
    • Inserta una herramienta de expulsión de SIM en el orificio de la bandeja SIM.

    • Presiona para expulsar la bandeja SIM.

  30. Remueve la bandeja SIM.
    • Remueve la bandeja SIM.

    • Cuando vuelvas a insertar la bandeja SIM, asegúrate de orientar la bandeja de tal manera que el orificio de expulsión SIM esté en la parte inferior.

  31. Remueve el único tornillo Phillips de 1.4 mm que sujeta el soporte de NFC en su lugar.
    • Remueve el único tornillo Phillips de 1.4 mm que sujeta el soporte de NFC en su lugar.

    The silver end of the NFC bracket goes here. The gold floppy end goes under the camera bracket.

    Thomas Hayes - Contestar

  32. Remueve el soporte de NFC. Remueve el soporte de NFC.
    • Remueve el soporte de NFC.

  33. Remueve los dos tornillos Phillips de 2.7 mm que sujetan el soporte del cable de control de audio a la placa lógica.
    • Remueve los dos tornillos Phillips de 2.7 mm que sujetan el soporte del cable de control de audio a la placa lógica.

  34. Remueve el soporte de cable de control de audio. Remueve el soporte de cable de control de audio.
    • Remueve el soporte de cable de control de audio.

    Wo kommt den der “6 s Plus Bluetooth Flex” überhaubthin bitte ?

    Also "das = https://www.ebay.de/itm/123934065844

    Mystery Shopper - Contestar

  35. Desconecta el cable de control de audio levantando su conector de su zócalo en la placa lógica. Desconecta el cable de control de audio levantando su conector de su zócalo en la placa lógica.
    • Desconecta el cable de control de audio levantando su conector de su zócalo en la placa lógica.

  36. Desconecta el cable de antena celular levantando su conector de su respectivo zócalo en la placa lógica. Desconecta el cable de antena celular levantando su conector de su respectivo zócalo en la placa lógica.
    • Desconecta el cable de antena celular levantando su conector de su respectivo zócalo en la placa lógica.

    how do you plug this cable back in? any tips for lining up with the socket? i can't get it to stay :(

    kapluni - Contestar

    Hold the cable with your tweezers and line the connector up over the socket as perfectly as you can, and then press straight down on it with the flat end of your spudger. Should snap into place with a bit of force.

    Jeff Suovanen -

    My problem when I pull the cable in the socket i shocked bot of them pull togeher the cable and the socket in the logic board the small circle i cry how to fix pleasss help mee

    Darrel Alan - Contestar

    The cable broke instead of coming out of the socket. Oh well. GG

    hiddenanddangerous2009 - Contestar

    My phone doesn't have a cable running here

    TJ Anderson - Contestar

  37. Desconecta el cable de antena de diversidad inalámbrica levantando su conectar de la placa lógica. Desconecta el cable de antena de diversidad inalámbrica levantando su conectar de la placa lógica.
    • Desconecta el cable de antena de diversidad inalámbrica levantando su conectar de la placa lógica.

  38. Desconecta el cable flexible del botón de encendido de su zócalo en la placa lógica. Desconecta el cable flexible del botón de encendido de su zócalo en la placa lógica.
    • Desconecta el cable flexible del botón de encendido de su zócalo en la placa lógica.

    Don’t forget this guy when you’re putting it back in! you’ll have to undo a bunch of screws

    Cassandra Vil - Contestar

  39. Desconecta el cable de antena de interconexión del conector Lightning levantándolo de la placa lógica. Desconecta el cable de antena de interconexión del conector Lightning levantándolo de la placa lógica.
    • Desconecta el cable de antena de interconexión del conector Lightning levantándolo de la placa lógica.

    This is not a Lightning connector - its a radio connector.

    NorthernBigDummy - Contestar

  40. Usa el extremo plano de un spudger para desconectar el cable flexible del conector Lightning de su placa lógica. Usa el extremo plano de un spudger para desconectar el cable flexible del conector Lightning de su placa lógica.
    • Usa el extremo plano de un spudger para desconectar el cable flexible del conector Lightning de su placa lógica.

    From here you can skip ahead to step 50.

    Mark Cousins - Contestar

  41. Desvía el cable de antena de los dos clips en el borde derecho de la placa lógica. Desvía el cable de antena de los dos clips en el borde derecho de la placa lógica. Desvía el cable de antena de los dos clips en el borde derecho de la placa lógica.
    • Desvía el cable de antena de los dos clips en el borde derecho de la placa lógica.

    This is super vague. Doesn’t explain exactly HOW to remove the cable from the clips, like it does in step 44. Slightly damaged my cable because I didn’t know how to remove it or the nature of the clip.

    Mason Rogers - Contestar

  42. Remueve los siguientes tornillos: Un tornillo Phillips de 1.3 mm
    • Remueve los siguientes tornillos:

    • Un tornillo Phillips de 1.3 mm

    • Un tornillo Phillips de 2.6 mm

    • Un tornillo separado de 2.2 mm

    • Los tornillos separadores se remueven mejor utilizando una punta de destornillador para tornillo separador de iPhone y un mango de destornillador.

    • Si no hay otra opción, un pequeño destornillador para cabeza plano hará el trabajo, pero ten cuidado para asegurarte de que no se resbale y dañe los componentes circundantes.

    Use can use a spudger in a pinch to dislodge the 2.2mm standoff screw. This was the most difficult screw in the phone. A Phillips bit will not work.

    mechamster - Contestar

    What do we call / name this bracket?

    B. Jansen - Contestar

  43. Remueve el soporte. Remueve el soporte.
    • Remueve el soporte.

  44. Desvía el cable de antena celular de la izquierda superior del primer clip de placa lógica empujándola desde debajo del clip hacia la batería. Desvía el cable de antena celular de la izquierda superior del primer clip de placa lógica empujándola desde debajo del clip hacia la batería.
    • Desvía el cable de antena celular de la izquierda superior del primer clip de placa lógica empujándola desde debajo del clip hacia la batería.

  45. Continúa desviando el cable de la antena celular del segundo y tercer clip de la placa lógica. Usa el extremo puntiagudo de un spudger para levantar el cable de antena celular del clip del medio de la placa lógica. No intentes removerlo tirando del cable ya que se puede arrancarse fácilmente.
    • Continúa desviando el cable de la antena celular del segundo y tercer clip de la placa lógica.

    • Usa el extremo puntiagudo de un spudger para levantar el cable de antena celular del clip del medio de la placa lógica.

    • No intentes removerlo tirando del cable ya que se puede arrancarse fácilmente.

    • Para que el cable llegue su cable en la placa lógica, debes dirigirlo por arriba de la placa lógica y por debajo del cable flexible del control de audio, como se muestra en la primera foto.

    My clip in the middle is not removing no matter how hard i pry or what i do, any help??

    David Gray - Contestar

  46. Remueve el tornillo Phillips final de 2.0 mm directamente por debajo del lector de tarjeta SIM.
    • Remueve el tornillo Phillips final de 2.0 mm directamente por debajo del lector de tarjeta SIM.

  47. Con cuidado levanta, pero no remuevas, la placa lógica desde el borde inferior más cerca del conector Lightning. Con cuidado levanta, pero no remuevas, la placa lógica desde el borde inferior más cerca del conector Lightning. Con cuidado levanta, pero no remuevas, la placa lógica desde el borde inferior más cerca del conector Lightning.
    • Con cuidado levanta, pero no remuevas, la placa lógica desde el borde inferior más cerca del conector Lightning.

  48. Inclina la placa lógica hacia arriba en posición vertical para exponer el único conector de antena en la parte inferior cerca del borde superior de la placa. No intentes aun de remover por completo la placa lógica, ya que la antena  Wi-Fi/Bluetooth está todavía conectada al lado inferior de la placa. No intentes aun de remover por completo la placa lógica, ya que la antena  Wi-Fi/Bluetooth está todavía conectada al lado inferior de la placa.
    • Inclina la placa lógica hacia arriba en posición vertical para exponer el único conector de antena en la parte inferior cerca del borde superior de la placa.

    • No intentes aun de remover por completo la placa lógica, ya que la antena Wi-Fi/Bluetooth está todavía conectada al lado inferior de la placa.

  49. Con cuidado coloca la placa lógica dada vuelta con la porción superior contra la caja del iPhone. Usa el extremo plano de un spudger para desconectar el cable de antena Wi-Fi/Bluetooth de su zócalo en la parte posterior de la placa lógica.
    • Con cuidado coloca la placa lógica dada vuelta con la porción superior contra la caja del iPhone.

    • Usa el extremo plano de un spudger para desconectar el cable de antena Wi-Fi/Bluetooth de su zócalo en la parte posterior de la placa lógica.

    Ugh, the socket connector separated from the back of the rigid cable. Two wires are still attached to the socket connector, but I’m guessing I’ll need to purchase a replacement WiFi/Bluetooth antenna cable at some point. I hope you sell these too?

    NorthernBigDummy - Contestar

    **Update** I used the tiniest drop of super glue with activator on both the connector and cable. It seems to be holding! Will reassemble and see if it works. Lucky for me, you sell the replacement cable for $14.99 if my cheap bastard fix fails :)

    NorthernBigDummy - Contestar

    **Update #2** Using super glue on the upper left wi-fi connector seems to have worked, both my bluetooth and wi-fi are working well post-repair.

    NorthernBigDummy - Contestar

  50. Remueve la placa lógica.
    • Remueve la placa lógica.

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

75 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

96%

¡ Mariana Roca nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Dante Mazzanti

Miembro Desde 13/07/15

35,524 Reputación

26 Guías creadas

23 comentarios

Great guide thanks. I just want to ask: Does screw length include the head or not? If not, what's the best way to measure those tiny screws? I have digital calipers but measuring them is quite awkward.

AMT - Contestar

Measurements are for the entire length of the screw, including the head. Putting the whole screw into a digital caliper should give you a reading very close to what you see here.

Jeff Suovanen -

Hi there! Great guide. Thank you. I was wondering if you ever removed the metal shields? If yes, how? I want to try to fix a water damaged phone.

Thanks!

LexiiCarrillo - Contestar

Hey so I'm having a Problem with my iPhone 6s plus it won't respond to my Finger touch> i cleaned it , i Hold Lock and Home Button and nothing still same thing, i also Restored cause that what apple Suggested to do if none of those steps worked. Please Guys i need help on this one i really don't wanna pay a whole 500$ for a new iPhone.

Vick - Contestar

i would replace the main logic board, make sure the board comes with the touch ID, as they are programed to work with the board. You will see main logic boards cheaper without the Touch ID. don’t buy that. I had to replace mine, and all is good now. If you are not good with working with installing the main logic board, buy one and have someone help you that knows how to do that.

Scott C -

Thanks for a great guide, is there any guide to remove the Sim Card reader for iPhone 6S plus to replace it?

Sevak - Contestar

Hi…once i replaced the logic board do i needed to replace also the touch id button?

ArnelCastillo - Contestar

If you want TouchID to work you will need to replace both.

Joe -

Best site, and best Techies, excellent job guys

Soufiane Louchene - Contestar

Great guide. In fact, if it wasn’t for the color coded screw highlights and their given lengths, I may not have been able to re-assemble the phone. Thanks!

Repair-IT - Contestar

guys where can i purchase the logic board ? TIA

jewen - Contestar

Suggestion on where to buy the logic board with paired home button?

Chris Bazydola - Contestar

AliExpress.com seems to be the best place to buy motherboards with or without touch id for multiple phone types.

Finn Arnold - Contestar

Hi,if i have a new motherboard for my 6s with no id tuch,does the phone work with no id tuch or is there error 53?

Raady - Contestar

Where can I purchase this logic board

nishion powell - Contestar

In Step 41, the 2.6mm phillips screw in my phone cannot be removed with the 000 driver as all the other screws. The head of mine seems to not be fully formed and starts to strip if I try and remove it. What should I do?

tdog69697 - Contestar

I bought my iPhone on fb and sold me the phone sim locked if I change the logic board will it unlock it so I can use it with any provider? ( if all of you are wondering why I am doing this is because they ghosted on me and when I reach out to the service provider they tell me the original owner has to call in to unlock it.)

TalkingMrFox - Contestar

I have an iPhone 6Splus bought it on eBay but the phone has an activation lock so if I change. The motherboard I solve the problem since I don't have access to contact the previous owner?

sammykendrickkasichi - Contestar

can you please help me, my iPhone is rebooting, it's shows white screen for some seconds and then reboot again.

Mohammed Adamu Ahmadu - Contestar

Please my iPhone is not starting when I press the power button it's just showed white screen and switch off automatically continues

Mohammed Adamu Ahmadu - Contestar

replace the logic board, this one clearly has some problems.

Tristan Haugh -

Great guide. I worked using a project board and noted the step next to the components removed. I ended up having about 10 or so blocks to put back following the guide in reverse order. Used it to fix “touch disease” on an iPhone 6+. working again 100%

Thanks again.

Glen Carrie - Contestar

Hi there, I lost my iPhone 6s plus for like five days and i see it in the six days inside a dirty water. can it still work or not

ARIA Jerry - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 13

Ultimos 7 días: 83

Ultimos 30 días: 456

Todo El Tiempo: 80,283