Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

Introducción

Si usted está teniendo un problema con la placa base (o algunos de sus puertos, como el HDMI, el USB, etc.) y necesita reemplazarla, esta guía es para usted. Tenga en cuenta que cualquier reemplazo o desmontaje más allá del disco duro anula la garantía de Sony

La extracción de la placa base separa la pasta térmica original entre el procesador y el disipador de calor. 'Antes de volver a montar su dispositivo' , vuelva a aplicar una nueva capa de pasta térmica. Sigaesta guía para aprender cómo.

  1. Voltear la PS4 boca abajo en su parte superior.
    • Voltear la PS4 boca abajo en su parte superior.

  2. Retire las cuatro pegatinas de la parte posterior de la PS4. Eliminar cualquiera de estas etiquetas anula la garantía con Sony.
    • Retire las cuatro pegatinas de la parte posterior de la PS4.

    • Eliminar cualquiera de estas etiquetas anula la garantía con Sony.

    Not true, removing stickers can’t void warranty as that’s illegal.

    Keyser Soze - Contestar

    Io però al di dietro ho solo 2 viti, quelle centrali. Come faccio?

    manuel gentili - Contestar

  3. Retire los cuatro tornillos TR9 de seguridad Torx de 9 mm de la parte posterior de la PS4.
    • Retire los cuatro tornillos TR9 de seguridad Torx de 9 mm de la parte posterior de la PS4.

    Depending on the model of PS4, (i.e. CHU-1001A vs. CHU-1215A) it may only have the two screws in the center, not the edge ones.

    Sawyer Coe - Contestar

  4. Con el dispositivo boca abajo, levante la parte trasera del dispositivo para retirar la cubierta inferior.
    • Con el dispositivo boca abajo, levante la parte trasera del dispositivo para retirar la cubierta inferior.

    This can be extremely tricky to do. Some force is needed and if using a tool to pry it open (and this might very well be necessary) you risk damaging or breaking the plastic. Just take your time and be mindfull of where you place your pry tools.

    Joakim Johansson - Contestar

  5. Retire los tres tornillos TR9 de seguridad Torx de 9 mm de la fuente de alimentación.
    • Retire los tres tornillos TR9 de seguridad Torx de 9 mm de la fuente de alimentación.

    • Quite los dos tornillos Phillips # 1 de 4 mm.

    It looks like that for CUH 1216A model, security TR8 and PH0 fits better

    sartoric - Contestar

  6. Desconecte el conector de la fuente de alimentación del enchufe. Levante la unidad de alimentación para sacarla de la caja.
    • Desconecte el conector de la fuente de alimentación del enchufe.

    • Levante la unidad de alimentación para sacarla de la caja.

    you need to lift the power board/box up vertically first as there are 2 long prongs extending up into the box. if you try to lift just one end you will bend the prongs.

    pollytintop - Contestar

    has anyone used any of these guys, i don't fancy doing it

    http://www.trustedrepairs.co.uk/electron...

    Damian - Contestar

    during this step it exposes a black phillips head screw at least on some models(such as mine) this screw mates the metal sandwich around the motherboard together. I was unable to perform step 19 until I released this Black short Phillips screw.

    gfinch1 - Contestar

    I just came across this screw at the same time. It is extremely stuck and I'm afraid to strip it. Any ideas?

    Richard Maya -

    The picture shows the power supply connector being removed from the main board instead of the power supply. This conflicts with the instructions which are correct given how it was most likely put together.

    Clay W - Contestar

    This is a poor instruction. Obviously you need to lift the psu out first but on my white ps4 it simply won't budge on one side. Now I'm stuck already.

    Rainer De Temple - Contestar

    Rainer, look at pollytintop’c comment. Lift vertically and you will get to next step. I used a screwdriver on the side opposite the fan, but I am a savage in many ways. If you insist on treating it delicately a small suction or powerful tape might work.

    We may not all make it back. Good luck

    Mello - Contestar

    Guten Tag,

    an dem Mainboard meiner PS4 ist die Buchse mit den Metallstücken drin, wo man den Stecker des Netzteils reinsteckt, abgebrochen. Als ich das Netzteil rausnehmen wollte, habe ich viel zu fest gezogen und nun ist es ab.

    Bilder: https://imgur.com/a/hIMeWTh

    Welche Methoden gäbe es dieses Problem zu beheben?

    Mit freundlichen Grüßen

    JotEssYT - Contestar

    It feels very stuck, but if you can just get the “more" stuck end up a little first (I gently used a screwdriver as a skinny finger) and hold it there with your real fingers, you can get the easier side up a little too, then lift both together simultaneously with your hands. (1001a model, here)

    Mr. Porter - Contestar

    Tip is to turn it upside down n gently wiggle the weight of it will bring it out

    Chicky Boy3 - Contestar

    the only way I found to unplug this was to have tweezers holding down the outer connector, then using your fingers to pull firmly but gently on the wires close to the connector, with some wiggling

    noah.mooresmith - Contestar

  7. Desconecte el cable de cinta de la unidad óptica presionando hacia abajo la lengüeta de liberación de metal y tire suavemente del cable de cinta. Esto no debe requerir fuerza. Desconecte el mismo cable de cinta de la tarjeta madre; Asegurándose de que está presionando hacia abajo en la pestaña de liberación de metal y tirando suavemente del cable de cinta.
    • Desconecte el cable de cinta de la unidad óptica presionando hacia abajo la lengüeta de liberación de metal y tire suavemente del cable de cinta. Esto no debe requerir fuerza.

    • Desconecte el mismo cable de cinta de la tarjeta madre; Asegurándose de que está presionando hacia abajo en la pestaña de liberación de metal y tirando suavemente del cable de cinta.

    If your PS4 eject button doesn’t respond/work and it doesn’t accept discs ( it doesn’t beep or nothing happens when you touch the eject button and it doesn’t make noise when you try to put a disc in and doesn’t take it) it could be because you took the wire ribbon out the optical drive or motherboard the wrong way and did not press down on the metal tab. ( like I did ) the wire ribbon should have these tiny “wings” on both sides and on both ends. Easy and very cheap fix. Ordered a new ribbon wire on amazon for $12!!! Better then buying a new PS4!!!!

    manny730 - Contestar

    Any way to get one of those wings out ? One of them broke off as I was pulling the cable out and is stuck.

    Luke Griffiths -

    Attention, pour sortir la nappe de connection du lecteur optique, il faut appuyer sur la lame métallique du connecteur avant de tirer sur la nappe, c’est un verrou.

    LOPAT - Contestar

    Just to emphasize, these are called ZIF cables, or “zero insertion force".

    Truly, you only need to press on the metal button and pull gently *straight* out. No wiggling. No yanking. There is no click.

    If you're putting it back in, the clip “clicks" into place by popping back up.

    Mr. Porter - Contestar

    Anyone knows how to remove the broken piece of ribbon stuck inside the connector?

    Sergio Colman - Contestar

  8. Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch

    Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch
  9. Desconecte el cable de la unidad óptica de la tarjeta madre.
    • Desconecte el cable de la unidad óptica de la tarjeta madre.

  10. Retire el cable wifi de la tarjeta madre.
    • Retire el cable wifi de la tarjeta madre.

  11. Quite los cuatro tornillos Torx de seguridad 9mm TR9.
    • Quite los cuatro tornillos Torx de seguridad 9mm TR9.

    • Retire el tornillo Phillips # 1 de 5 mm.

    Mine on the bottom right near the board was a 5mm Phillips #1 instead of the expected 9mm Torx screw. Also, I have a shield plate covering my (or my customer's) board here.

    CPR Matthews, NC - Contestar

    Mine is the same

    Jesse King - Contestar

    Model Cuh1001a

    Jesse King - Contestar

    the guide has missed the optical drive shield. DO NOT PROCEED WITHOUT REMOVING IT. the “optical drive cord “ must be removed from the drive to continue.

    Max R. - Contestar

    This guide does not explain how to remove the metal plate on top of this board.

    Nicola Centrone - Contestar

  12. Retire la antena wifi.
    • Retire la antena wifi.

  13. Levante la unidad óptica y retírela del sistema.
    • Levante la unidad óptica y retírela del sistema.

  14. Vuelva a girar el sistema y retire el panel superior izquierdo presionándolo hacia atrás y levantándolo.
    • Vuelva a girar el sistema y retire el panel superior izquierdo presionándolo hacia atrás y levantándolo.

  15. Retire los dos tornillos Torx de seguridad TR9 de 9 mm.
    • Retire los dos tornillos Torx de seguridad TR9 de 9 mm.

    • Retire el tornillo Phillips # 1 de 5 mm.

  16. Jale y extraiga el disco duro del sistema.
    • Jale y extraiga el disco duro del sistema.

  17. Levante la parte frontal de la cubierta superior y deslícela hacia atrás.
    • Levante la parte frontal de la cubierta superior y deslícela hacia atrás.

    my right corner, by the ps4 logo, was VERY snug, it took me a few minutes to pop that corner off, took a decent amount of force to pop it off

    theyoonion - Contestar

    we used the screwdriver to pry it open in the corner

    Sabrina Shahid - Contestar

    I try being extremely gentle when working with electronics, but you need a tad more force this. Perhaps you'll need the same force for pulling those miles cables for the optical drive earlier. :)

    Mr. Porter - Contestar

  18. Retire los doce tornillos de 9 mm TR9 de seguridad Torx.
    • Retire los doce tornillos de 9 mm TR9 de seguridad Torx.

    There’s a black Phillips screw next to the power supply connector that needs removed before removing the metal cover.

    louhobby - Contestar

  19. Quite los dos tornillos de 9 mm Phillips # 1. Retire el soporte de metal.
    • Quite los dos tornillos de 9 mm Phillips # 1.

    • Retire el soporte de metal.

    Danach muss auf der Innenseite noch eine schwarze Schraube gelöst werden, sonst kann man die Abdeckung und auch nicht Mainboard lösen.

    Maik Heidemann - Contestar

  20. Levante y retire la cubierta metálica.
    • Levante y retire la cubierta metálica.

    On some PS4 consoles there is a small black Phillips head screw under the PSU securing the metal cover to the midframe of the console. If you do not remove this screw you will not be able to remove the metal cover, and run the risk of damaging it, or the motherboard.

    Jordan Troxel - Contestar

  21. Desconecte el enchufe de tres cables de la placa base levantando suavemente hacia arriba y lejos de la placa base. Desconecte el enchufe de tres cables de la placa base levantando suavemente hacia arriba y lejos de la placa base.
    • Desconecte el enchufe de tres cables de la placa base levantando suavemente hacia arriba y lejos de la placa base.

    What can i do if i broke these three little prongs?

    Josh Turner - Contestar

    2 options 1 make a new contact, 2 buy a New fan as it is The fan contact ;)

    Karl eriksson -

    Which kind of connector is this?

    robbitara - Contestar

    Hab meine Halterung auch Abgebrochen.

    Das Komplette “ding” ist vom Mainboard/PCB Abgebrochen…

    Was kann man tun?

    Cem Ce - Contestar

    Hab meine Halterung auch Abgebrochen.

    Das Komplette “ding” ist vom Mainboard/PCB Abgebrochen…

    Was kann man tun?

    Georgios -

    I accidentally pulled the little red cord out from the white casings. Can I shove it back or do I need a new fan?

    Hobocop - Contestar

    Place one side of tweezers under from wire side, pinch with tweezers, and use to lift up, this pulls the wire out of the lock. (They aren't pins inside, but fins.)

    Mr. Porter - Contestar

    Having no patience I pulled all 3 fan wires out of connector on motherboard but all wires have there metal connector tips so can I put back into motherboard or did i ruin my fan

    asmar wash - Contestar

    Please be EXTREMELY careful, as it is exceedingly easy to break that connector. ☹️

    Except, of course, if you actually plan to replace the fan anyway, well, a new connector comes with the fan, so just look out for the motherboard part of it.

    Wolfgang Bachmann - Contestar

    Help!! Si è staccato il connettore dalla scheda madre come lo riattacco????

    Grazie

    Emanuele Lucidi - Contestar

  22. Levante y retire la tarjeta madre del sistema.
    • Levante y retire la tarjeta madre del sistema.

    • La extracción de la tarjeta madre separa la pasta térmica original entre el procesador y el disipador de calor. Antes de volver a montar el dispositivo, vuelva a aplicar una nueva capa de pasta térmica. Siga esta guíapara aprender cómo hacerlo.

    Unfortunately it costs more for the motherboard and optical drive together than it costs for a new PS4 1TB with a game

    Blake Hannan - Contestar

    Was passiert wenn man das nicht macht?

    Und was passiert mit der ps4 ohne Wärmeleitpaste ich hab nämlich meine ps4 geöffnet und die Wärmeleitpaste abgewischt und ich habe es zusammen gebaut und die ps4 piept nur 3 mal und geht aus.

    Könnt ihr mir Helfen?

    danke shirin - Contestar

    @danke shirin die gleiche hat zu mir passiert. It also happened to me, I did this tutorial and put everything back together, and now it beeps three times red and goes off. I used paste but I guess it is because of sth else

    anonymous 2356 - Contestar

Conclusión

Para volver a armar el dispositivo, siga estas instrucciones en orden inverso.

141 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Robert Harvey

Miembro Desde 01/04/14

8,490 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 8-12, Regan Spring 2014 Miembro de Cal Poly, Team 8-12, Regan Spring 2014

CPSU-REGAN-S14S8G12

5 Miembros

35 Guías creadas

Regarding the three wire plug in step 20 - is there a good way to repair this piece if, say, you pulled the wires out of the connector by accident? is there a place to get a replacement part?

Ryan Statz - Contestar

how would i know which mother board and paired optical drive is compatible with my ps4 model?

chandra sekhar - Contestar

I have tried to replace the hdmi port however being somewhat of an idiot I slipped and knocked off onto the little black squares just behind the port on the left hand side. Does anyone know what these are?

Geoff Parker - Contestar

contacts of the motherboard

lillarrypimp1993 -

You may be talking about capacitors that are critically important for the unit to function.

South30 -

Ok so I was taking mine apart, and while I was separating the ribbon wire from the optical drive during step 7, I broke the top off the connector by accident. I thought I could fix it with hot glue, but my ps4 doesn't read disks (at all, doesn't even know there's a disk in the drive). Is there a way to repair this without getting a new drive?

jonathanhart54 - Contestar

when I bought the replacement motherboard and optical drive and installed everything, I got a message saying connect USB with software update. Is this because I'm using my original hdd from my original mobo+ optical drive that is different from the hdd my replacement parts came with?

Quaymetsu - Contestar

Could you please tell me where you bought a replacement motherboard from as i've been looking everywhere!?

Roger flaps -

Does your blu-ray drive still work on the new motherboard? I seem to recall on the PS3 that the blu-ray drive was tied to a console, I assume you had to reformat the HDD also?

Andrew Fox - Contestar

Am I able to buy just the motherboard without buying the optical driver? and if so or not how will I know which one to buy?

Jeff deem - Contestar

Cómo saber que tarjeta es la indicada

Oscar Mora - Contestar

Es q tengo una ps4 slim y la tarjeta está dañada pero nose cual es la indicada xq trae unos números y nose si afecta en algo

Oscar Mora - Contestar

Por favor la respuesta a mi correo gracias :: oscardanilo1724@gmail.com

Oscar Mora - Contestar

Desarme la ps4 la limpie arme y andaba…resultado que cuando saque la fuente de alimentación desconecte un pin que que está en la placa base es blanco con unas fichas lo solde e igual no funciona …le pasa corriente pero muy poca que puede ser ayudaaaa

pablolopez 19 - Contestar

Pablolopez1095@gmail.com ayuda …es mi correo alguna

pablolopez 19 - Contestar

Boa tarde, meu playstation 4 não consigo conectar os controles nas portas USB, ambas não funcionam, já utilizei um teste de porta USB, ambas não funcionam, alguém tem uma ideia?

medron - Contestar

Brought a used ps4 any idea how to remove the ribbon port of the motherboad step by step to replace. Someone put crazy glue on it..

Ramon Camacho - Contestar

im thinking of running for president

Zany Boy - Contestar

Thanks for this informative post <a href="http://www.buyplaystation.com/">buyplaystation.com</a>

buyplaystation - Contestar

You cannot just replace the motherboard on a PS4. The motherboard is married to the logic board on the blu-ray drive. Swapping the motherboard without carrying over the original logic board will render the drive useless.

Will - Contestar

I ordered a new HDMI port because it was just a black screen but the receivers on the motherboard are worn down, what should I do

Josh coates - Contestar

Hi Iwas cleaning my ps4 and pull the power connection and it is lose I bought another ps4 and tried to put my hard drive in the new one but doesn’t work. Somebody can help me. It’s posible just to change the mother board I have a lot of games there. Thanks

Josue hernandez - Contestar

Motherboad of ps5 we are wating for the ps4 we need best hard drive for ps4 which can enhance the capability of ps4.

best psvr games - Contestar

welding jkgfkjjfhkfiyfyiryiriyriyriyr

tarloksingh415 - Contestar

tig hjjjjjjjjjjjjjjjjjjjjfkkkkkkhhkfkfkhf

tarloksingh415 - Contestar

sir i want ps4 motherboard,did u have ps4 motherboard.

haider ali - Contestar

I’ve read along the guides that a BDP-020 optical drive can work with an SAA-001 motherboard, but mine still receives the CE-35888-2 error. Am I replacing the incorrect part?

Cristian Nickles - Contestar

Hi my ps4 has stopped working and doesnt turn on at all, ive tried different outlets and different power cables for the ps4, still no luck. Ive pulled it apart and had a look at the power supply board and mother board aswell as dusted it all out. The mother board has yellow stains/ dots near the hdmi port and some other random spots around the mother board. I have the first ps4.

Does anyone know whats wrong? Id rather fix it than pay for a new one.

Jared Breen - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 108

Ultimos 7 días: 851

Ultimos 30 días: 4,655

Todo El Tiempo: 196,726