Esta traducción podría no reflejar los cambios más recientes añadidos a la guía de referencia. Ayúdanos a actualizar la traducción o revisa la guía original.
Introducción
Debe tenerse en cuenta que, aunque esta modificación agregará memoria adicional a la consola, infringe los términos de servicio de Xbox Live y podría provocar el destierro de Xbox Live.
Aquí te muestro el reemplazo bastante simple de la unidad de disco duro real en el gabinete HDD de 360. Microsoft hace que sea costoso o difícil actualizar tu disco duro limitando tus opciones con dicha actualización. Esta guía trata sobre cómo desmontar físicamente la unidad y reemplazarla con su nuevo y brillante disco duro WD. Sí, por alguna razón tiene que ser una unidad Western Digital. Una de las siguientes series de unidades:
-WD Scorpio Series BEVS/BEAS
-WD Scorpio Blue Series BEVS/BEVT
-WD Scorpio Serie Negra BEKT/BJKT
-Serie WD VelociRaptor
Busqué en Newegg.com y encontré una unidad Scorpio Black de 250 GB girando a 7200 RPM con 16 MB de caché y 3.0Gb/s. por alrededor de $65. Eso es lo que probablemente recomendaría ya que tu dinero rendirá más y es aproximadamente la mitad de lo que MS le cobrará por la unidad de 250 GB
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Here it is. The standard 20GB HDD for the Xbox 360.
-
Notice the proprietary adapter. Inside is just a pretty standard 2.5" SATA drive...
-
I took these pictures as I was putting it back together, hence the Microsoft warranty sticker looking a little funny.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
It only voids the warranty for the drive, not the console, being as their warranties are separate.
-
Proceed to remove the four T6 Torx screws.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Holding the drive top up, gently pull the top half up from the bottom half. The back will rotate up as the front is connected by two plastic clips.
-
These clips are most easily undone by rotating the top enclosure to about 30º then lifting it up firmly.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four T10 Torx screws.
-
Slide the cover towards the back of the enclosure and remove. There is a small dot of lock-tite on each screw, fyi.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Here are the innards in all their glory.
-
The four screws that held the cover on also held the drive in place, so just pull off the SATA connector and the drive is almost free.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
To actually get the drive out, you must bend the back of the plastic part of the bottom enclosure down a little bit. Doing so shouldn't break anything, just don't go overboard and bend it excessively.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
All the parts disassembled. The adapter cable will probably come out as it doesn't seem to be attached directly, but removing it would have required bending the metal enclosure and I didn't want to mess with that.
-
I thought it interesting to note that the drive runs at 5V 0.62A when the enclosure states 5V 1A. I wonder where the other 380mA are going.
-
Also interesting to note: this is a Seagate drive, while the 250GB drive upgrade I mention in the description requires a WD drive. If I understood correctly, this is because the software to format the drive to be recognized by your 360 is written for the WD firmware.
-
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
66 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
36%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
3 comentarios
I happen to have an external HD enclosure (the original HD had a platter crash) that works perfectly to mount the XBox 360 HD to my PC for all sorts of uses, allowing for either USB or external SATA connectivity. :D
Link to article seems to be down. Any mirrors? It woulb be much appreciated, Thanks
Sounds and looks easy enough. But will replacing a 20 go drive with a 250 go drive now need any formatting or can I just plug it in and work?