Saltar al contenido principal

Qué necesitas

  1. Nintendo Switch Rear Panel Replacement, Release the Joy Con controller locking tabs: paso 1, imagen 1 de 3 Nintendo Switch Rear Panel Replacement, Release the Joy Con controller locking tabs: paso 1, imagen 2 de 3 Nintendo Switch Rear Panel Replacement, Release the Joy Con controller locking tabs: paso 1, imagen 3 de 3
    • Before you begin this repair, make sure the device is completely powered off.

    • Press and hold down the small round button on the back of the Joy Con controller.

    • While you hold down the button, slide the controller upward.

  2. Nintendo Switch Rear Panel Replacement, Remove the Joy Con controllers: paso 2, imagen 1 de 3 Nintendo Switch Rear Panel Replacement, Remove the Joy Con controllers: paso 2, imagen 2 de 3 Nintendo Switch Rear Panel Replacement, Remove the Joy Con controllers: paso 2, imagen 3 de 3
    • Continue sliding the controller upward until it's completely removed from the console.

    • Repeat this same process for the other controller.

    • Use a Y00 screwdriver to remove the four 6.3 mm-long screws securing the rear panel.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

  3. Nintendo Switch Rear Panel Replacement, Remove the top and bottom screws: paso 4, imagen 1 de 2 Nintendo Switch Rear Panel Replacement, Remove the top and bottom screws: paso 4, imagen 2 de 2
    • Use a JIS 000 screwdriver to remove the following screws securing the rear panel:

    • One 2.5 mm-long screw on the top edge of the device

    • Two 2.5 mm-long screws on the bottom edge of the device

    • If you don't have a JIS screwdriver, you can use a Phillips in a pinch. Be very careful, as a Phillips driver can easily cam out and strip the screwhead.

  4. Nintendo Switch Rear Panel Replacement: paso 5, imagen 1 de 2 Nintendo Switch Rear Panel Replacement: paso 5, imagen 2 de 2
    • Use a JIS 000 screwdriver to remove the two 3.8 mm center screws on the sides of the device (one on each side).

  5. Nintendo Switch Rear Panel Replacement: paso 6, imagen 1 de 2 Nintendo Switch Rear Panel Replacement: paso 6, imagen 2 de 2
    • Use your finger to flip up the kickstand on the back of the device.

    • If there's a microSD card in the microSD card slot, remove it now before you continue to the next step.

  6. Nintendo Switch Rear Panel Replacement: paso 7, imagen 1 de 1
    • Use a JIS 000 screwdriver to remove the 1.6 mm screw in the kickstand well.

    • Close the kickstand.

  7. Nintendo Switch Rear Panel Replacement: paso 8, imagen 1 de 3 Nintendo Switch Rear Panel Replacement: paso 8, imagen 2 de 3 Nintendo Switch Rear Panel Replacement: paso 8, imagen 3 de 3
    • Open the game card cartridge flap.

    • The game card cartridge flap attaches to the other half of the plastic shell, preventing you from completely lifting up the rear panel if it's closed.

    • Lift the rear panel up from the bottom of the device and remove it.

Conclusión

Compare your new replacement part to the original part. You may need to transfer remaining components from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Nintendo Switch Answers community for help.

62 personas más completaron esta guía.

Craig Lloyd

Miembro Desde 10/02/16

28,583 Reputación

82 Guías creadas

9 comentarios

Excellent and concise guide.

The new panel doesn’t come with the sticky grille pieces x 2 on the bottom. Is it supposed to be a straight transfer between the old and the new?

fclbriat123 - Contestar

You can transfer the grill to the new back plat

Phillip Norton -

Just did this replacement and there are a few things to keep in mind that this review does not mention. There are x2 square foam pieces that can be transferred to the new panel located at the bottom backside of the old. Also, the game cartridge shield hardware and the kickstand holder hardware have to be taken off the back of the old panel and transferred to the new panel. The kickstand has 2 Phillips #000 screws and the game cartridge shield has 1 Phillips #000 screw

Ryan Talbert - Contestar

How do you transfer the foam pieces? Use some heat to loosen their adhesive and then remove them and transfer over the new backplate?

John - Contestar

Is the casing the same between the HAC model and the HAD model? This guide doesn’t specify

Julian Webb - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 65

Ultimos 7 días: 512

Ultimos 30 días: 2,438

Todo El Tiempo: 61,263