Robert G

I just got an iMac 21.5" A1418 - Late 2013 (EMC 2638) with a broken screen/LCD and i have laying around a iMac 21.5" A1418...

Hi, i hope anyone have solved this issue or determine the cause of it. My iMac display suddenly started glitching. (No...

Im getting this issue on a A1278 Mid-2012, but is pretty occasionally, sometimes the image will get distorted but only on...

So im getting this weird issue, on my magic keyboard. The down arrow does’t work by itself. no water damage but if i press...

So im having this issue with my MacBook Air early 2014. It won´t turn on unless plugged in to the charger and after...

I replaced the whole LCD assembly of a A1502 EMC-2835 with a A1502 EMC-2875 and this is my experience. BACKSTORY (1) No...

Im getting this issue with an iPhone 8. Touch functionality doesn’t work with an specific OEM screen, but if i replace it...

Hi, Im having an issue with an iPad 3. - Already replace the dock connector, but the battery charges real slow, about 15%...

I have this issue with my mac, and its that when i apply slight pressure to the case some black squares appear on screen...

I have no issue with my phone. I just found this "glitch" with one of them In my iPhone 6 the carrier is not showing on...

applying isopropyl and acetone can damage the oleophobic coating and also the gaskets that make your phone splash proof. i had tried many household items, with no luck removing the scratches.

tip #1 patience. tip #2, hair dryer for this is not the best tool, i would recommend a glass heating plate. this will heat equally the back glass of your phone. then you can use a very thin ic removal blade just to unglue the glass from the frame. (you just need lica 1/2 inch so you can insert a metro card, careful the glass breaks pretty easy). then use a typical metro card and with a syringe inject little isopropyl alcohol where you are moving the metro card. reheat the back glass as needed. check where ir the fingerprint scanner flex cause you can damage it easily. also careful with the NFC antenna qi charger coil. Good luck PS. most youtube videos will show you an already removed glass, and remove it again as they record, looks pretty easy.

that is called ripped pads on the motherboard, and its bad, if you have schematics, you can check what the damaged pads are for. maybe you can bridge them. you have to practice more, since this happens when you don’t use the correct amount of air/heat/flux. this all depends on the calibration and brand of your hot air station. keep practicing

Battery is the same for this models

On any lcd/led monitor any buzzing sound linked to brightness intensity, is pretty common to be a hardware issue, maybe a swollen capacitor.

Can you please add pictures of the damage

I have done this before and I found out that you can swap the displays and it will work, but with some issues. (i´m not sure exactly of the parts number i used, but in my experience) What I encountered so far, is that: - When turning on the MacBook the Apple logo and loading bar screen will show after a couple of seconds. - Sometimes the backlight will lock up and will not increase/decrease, this can easily be fixed by “sleeping your screen”, then turning it back on, i set that the lower left corner of the desktop will sleep my screen, so whenever i have this issue i just roll the cursor to that corner. iSight camera, bluetooth and WiFi works perfectly.

The OEM will work flawless on a different iPhone 8. Already tried dfu, upgrade to ios12 then downgrade, issue persist.

Also this issue was present on iOS 11.3 when using an aftermarket LCD. You can try updating to 11.3.1. Sometimes it can fix this issue.

It sounds like a faulty Audio IC chip and this can be fixed by the jumper wire - reball method. If it fails, then you would have to replace the Audio IC. A somewhat difficult task if you are not familiar with this type of repair level. I have fixed 5 phones with this exact same issue, already fixed.

hahaha i agree

I found out that you can swap the displays and it will work, but with some issues.

What I encountered so far, is that:

- When turning on the MacBook the Apple logo and loading bar screen will show after a couple of seconds.

- Sometimes the backlight will lock up and will not increase/decrease, this can easily be fixed by “sleeping your screen”, then turning it back on, i set that the lower left corner of the desktop will sleep my screen, so whenever i have this issue i just roll the cursor to that corner.

iSight camera, bluetooth and WiFi works perfectly.

iPhone XR GTS SS Z11 LX Turbo Limited Luxury 2.0 Edge

The Good, you can transfer the TouchID to a new touchscreen, if you damage it.

I don't think so since he change from home button to TouchID, the size always are different...

Are the motherboards swappable from the late-2009 macbook and the mid-2010 macbook?