Saltar al contenido principal

La Kenmore Elite HE3 es una secadora eléctrica con una capacidad de 7.2 pies cúbicos de Kenmore.

Preguntas 319 Ver todo

My dryer been over heating and now it doesn’t start.

I can’t figure out what’s wrong with my dryer please help. It worked fine and dried my clothes but the dryer would get pretty hot and now when I try to press start nothing happens. I can turn the power on and off but when I click the start it won’t start the dryer. It’s a kenmore elite smart heat quietpak 4 he3.

Contesta esta pregunta Yo también tengo este problema

Es esta una buena pregunta?

Puntuación 0
2 comentarios

Anita Babak what is the exact model number for your Dryer?

- de

Agregar un comentario

3 Respuestas

Respuesta Más Útil

Anita Babak there are several components that an cause your dryer not to start. It could be a faulty timer, thermal fuse, door switch, start button, or improper voltage. Start by testing the outlet first to make sure you are getting a full 240 volts. If you are not then, you will need to check your breakers. If you are, then you will need to test the internal components. There start with the thermal fuse, since it is the most common issue for a dryer and yours had shown signs of overheating already. The thermal fuse is located on the outside of the blower hosing. It is a small plastic part with two wires going to it. You need a multimeter and test for continuity.If you are getting continuity, then you will need to check the rest of the components.

I attached the tech sheet which should work for your dryer and will help you with the diagnostic and the repair of your dryer. ZB70972_W10156034A.vp

Fue útil esta respuesta?

Puntuación 2
Agregar un comentario

Solution 1:

Heating Element

The heating element warms the air before the air enters the dryer drum. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. When this happens, the dryer gets too hot. To determine if the heating element is at fault, use a multimeter to test each terminal for continuity to the case. If the heating element has continuity to the case, it is shorted out. If the heating element is shorted out, replace it.

Dryer Heating Element WP8544771

Genuine OEM Part # WP8544771

Imagen de WP8544771 - Whirlpool Dryer Heating Element

Producto

WP8544771 - Whirlpool Dryer Heating Element

$75.99

Fue útil esta respuesta?

Puntuación 1

2 comentarios:

Where can I find the model number ?

- de

On most Kenmore Elite dryers, the model number sticker is around the opening of the door. Open the dryer door and look around the outside of the door opening. Some dryers have the sticker on the bottom left or right side. Some dryers have the sticker on the top right side

- de

Agregar un comentario

Hi,

Check if the thermal fuse and thermal cut out fuse are both OK.

The thermal fuse if blown will prevent the dryer from starting and heating.

The thermal cut out fuse stops the dryer from overheating.

A faulty thermal cut out fuse would have allowed the heater to get too hot (which may have damaged the heater element -hopefully not) and caused the thermal fuse to blow, shutting off the power to the heater so as to prevent a possible fire

Imagen de WP3392519 - Whirlpool Dryer Thermal Fuse

Producto

WP3392519 - Whirlpool Dryer Thermal Fuse

$15.99

Fue útil esta respuesta?

Puntuación 1

1 comentario:

Where is the thermal fuse located on the dryer?

- de

Agregar un comentario

Añadir tu respuesta

Anita Babak estará eternamente agradecido.
Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 5

Ultimos 30 días: 40

Todo El Tiempo: 1,398