Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Guías de reparación y soporte para ensamblajes de secadora y lavadoras así como también unidades apiladas.

Preguntas 76 Ver todo

frigidaire works ok, bout only fills with cold water

model number ffle1011mw2 frigidaire stackable washer and dryer. All settings work ok; fills with water after selecting either hot or cold, but water in tub is always cold. All cycles run to completion. Checked water hoses: not kinked, hot water getting to washer ok.

Contesta esta pregunta Yo también tengo este problema

Es esta una buena pregunta?

Puntuación 2
Agregar un comentario

7 Respuestas

Respuesta Más Útil

Just fixed a similar stacking washer with the same problem.

Set your wash temperature to hot and start a fill. If very little water coming in try this...

Turns out there is a filter screen inside the hose connections on the washer. The hot was plugged up due to some previous water line flushing.

A good scrub with a Q-tip and hot water was flowing happily again.

Fue útil esta respuesta?

Puntuación 2
Agregar un comentario

This happens to me. The pipes have to warm up by running hot water through them. If the washer is close to the kitchen open the sink hot water valve first and see how long it takes hot water to get to it. (This cold water from the hot water side is what is first getting to your machine). Once it is hot then try the washer.

Fue útil esta respuesta?

Puntuación 1
Agregar un comentario

Hi

I think Mr Mayer might be on to it. Try to remove the hot water hose at the washer and turn the valve on the wall on.Run the hot water till it is hot. Now connect it again and turn the washer to hot wash and cold rinsing.Check if the water is hot.If it is cold the hot and cold hoses might be switched.

Fue útil esta respuesta?

Puntuación 1
Agregar un comentario

Frigidare Model FFLE1011mw2 won’t finish a fill cycle. It starts to fill then quits. Have only had the washer eight mos.

Fue útil esta respuesta?

Puntuación 0

Comentarios:

How much filling does it do before it quits?

What wash temperature did you select? Try hot-only, then try cold-only do they both fill? If so then the washer not only is getting the water but the valves inside is letting the water in. All that's left is the tubing/hoses between the tub and fill valves.

If one temperature doesn't fill then it could be that temperature line is plugged or the valve not working. Try swapping hot for cold hoses at the washer and see if cold fills with hot setting or hot with the cold setting.

My cold water hose has a strainer at the faucet and it was plugged so cold wouldn't fill. I tried filling with hot and that worked.

Touch the washer where the hoses connect & start the fill. You should feel the valve open and hear a click. If you don't then the valve is likely faulty.

As Pete said 20140624, disconnect the washers hose and turn on the water (with the hose in a bucket or the washer drain line). That proves the water supply to the washer. Everything else is "in the wash"er.

- de

Agregar un comentario

Are you sure hot water is actually running thru the line? If it has a mixing valve the silenoid could be bad.

Fue útil esta respuesta?

Puntuación 0

Comentarios:

Yes, I stood there today and kept checking as it was filling - very hot. However the water in the tub was cool/cold. It almost seems like there is water that remains under the tub from a previous wash, by then cold, and a significant amount of it. I'm sure that's crazy. Top load washer.

- de

Agregar un comentario

I replaced the user interface A00540602 on mine, this fixed it

Fue útil esta respuesta?

Puntuación 0
Agregar un comentario

This was for a top loading washer

Fue útil esta respuesta?

Puntuación 0
Agregar un comentario

Añadir tu respuesta

Steve estará eternamente agradecido.
Ver Estadísticas:

Ultimas 24 horas: 7

Ultimos 7 días: 25

Ultimos 30 días: 97

Todo El Tiempo: 3,374