Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Apaga tu iPhone antes de comenzar el desmontaje.
-
Retira los dos tornillos Pentalobe P2 de 3.6mm junto al conector Lightning.
-
-
Herramienta utilizada en este paso:Anti-Clamp$24.95
-
Tira de la manija azul hacia atrás para desbloquear los brazos del Anti-Clamp.
-
Desliza los brazos sobre el borde izquierdo o derecho de tu iPhone.
-
Coloca las ventosas cerca del borde inferior del iPhone, justo encima del botón de inicio, una en el frente y otra en la parte posterior.
-
Aprieta las copas para aplicar succión en el área deseada.
-
-
-
Tira de la manija azul hacia adelante para bloquear los brazos.
-
Gira el mango en el sentido de las agujas del reloj 360 grados o hasta que las copas comiencen a estirarse.
-
Inserta una púa o herramienta de apertura debajo de la pantalla cuando Anti-Clamp cree un espacio lo suficientemente grande.
-
Omite los siguientes tres pasos.
-
-
-
Usa una ventosa para separar el panel frontal:
-
Presiona la ventosa sobre la pantalla, justo arriba del botón de inicio.
-
-
-
Mientras sostienes el iPhone hacia abajo con una mano, tire hacia arriba de la ventosa para separar ligeramente el conjunto del panel frontal de la caja trasera.
-
Con una herramienta de apertura de plástico, comienza a hacer palanca con cuidado hacia abajo la caja trasera, alejándola del conjunto de la pantalla, mientras continúas tirando hacia arriba con la ventosa.
-
-
-
Tira del extremo del botón de inicio del ensamblaje del panel frontal para separarlo de la caja posterior, utilizando la parte superior del teléfono como una bisagra.
-
Abre la pantalla en un ángulo de aproximadamente 90º y apoyala contra algo para mantenerla levantada mientras está trabajando con el teléfono.
-
Agrega una banda de goma para mantener la pantalla de forma segura en su lugar mientras trabaja. Esto evita una tensión excesiva en los cables de la pantalla.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws securing the antenna bracket to the rear case:
-
One 1.5 mm Phillips #00 screw
-
One 2.8 mm Phillips #00 screw
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Tweezers$4.99-
Grasp the 5GHz Wi-Fi antenna bracket with a pair of tweezers and lift it off the iPhone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully pry the 5GHz Wi-Fi antenna connector up off the logic board with a plastic opening tool.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the 5GHz Wi-Fi antenna connector with a pair of tweezers and gently lift it from its retaining clip on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the power button cable and audio control cable connectors from their respective sockets on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws securing the 5GHz Wi-Fi antenna to the rear case:
-
One 2.8 mm Phillips #00 screw
-
Two 1.6 mm Phillips #00 screws
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a pair of tweezers to grasp and remove the 5GHz Wi-Fi antenna out of the iPhone.
-
-
-
Levanta el cable conector del vibrador de su zócalo en la placa lógica con el extremo plano de un spudger.
-
-
-
Inserta la herramienta de expulsión de tarjeta SIM o un clip de papel en el pequeño orificio en la bandeja de tarjeta SIM.
-
Presiona para expulsar una bandeja.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 2.8 mm Phillips #00 screw securing the plastic clip to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 1.3 mm Phillips #00 screw recessed against the top of the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Tweezers$4.99-
Use a pair of tweezers to firmly grasp the plastic clip and remove it from the iPhone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 1.6 mm Phillips #00 screw securing the antenna clip to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully grasp the antenna clip with a pair of tweezers and remove it from the iPhone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Standoff Screwdriver for iPhones$5.49-
Remove the following screws securing the logic board to the rear case:
-
Two 2.4 mm standoff screws
-
One 2.1 mm Phillips #00 screw
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully raise—but do not remove—the logic board, lifting it from the bottom edge nearest the Lightning connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue carefully lifting the bottom side of the logic board until it is vertical.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently lay the logic board upside-down, with the top portion resting against the rear case of the iPhone.
-
Use the flat end of a spudger to disconnect the antenna connector from its socket on the back of the logic board.
-
Cancelar: No complete esta guía.
182 personas más completaron esta guía.
31 comentarios
Hello. Good job on these teachings of disassembly. I need help in changing the logic board of my iphone 5 and iphone 6. Where can i buy the logic board? I reside in Nigeria
HI do you know who replaces logic boards on iPhone 6?
I am on Step 29 and the upper-right screw was stripped in manufacturing and I am not able to remove? What is the best way to remove the stripped screw?
if u can melt a pen and stick it on then twist it if that dosen’t work use a dermel cut the screw and use a flahead