Saltar al contenido principal
  1. Este paso está sin traducir. Ayuda a traducirlo

    Gently pull the left speaker cable straight out of its socket on the logic board. Gently pull the left speaker cable straight out of its socket on the logic board.
    • Gently pull the left speaker cable straight out of its socket on the logic board.

  2. Este paso está sin traducir. Ayuda a traducirlo

    De-route the left speaker cable by pulling it straight up out of the retaining clip in the back of the rear enclosure.
    • De-route the left speaker cable by pulling it straight up out of the retaining clip in the back of the rear enclosure.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Similarly to the previous step, de-route the SATA and power cables by pulling the braid straight up out of the retaining clip. Similarly to the previous step, de-route the SATA and power cables by pulling the braid straight up out of the retaining clip.
    • Similarly to the previous step, de-route the SATA and power cables by pulling the braid straight up out of the retaining clip.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Peel up the piece of tape connecting the left speaker connector to the SATA power and data cables. Peel up the piece of tape connecting the left speaker connector to the SATA power and data cables.
    • Peel up the piece of tape connecting the left speaker connector to the SATA power and data cables.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Flip up the metal retaining bracket on the FaceTime camera cable connector. Pull the FaceTime camera cable straight out of its socket on the logic board. This is a delicate connector that can be easily damaged.
    • Flip up the metal retaining bracket on the FaceTime camera cable connector.

    • Pull the FaceTime camera cable straight out of its socket on the logic board.

    • This is a delicate connector that can be easily damaged.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Remove the two 4.0 mm T5 Torx screws securing the four antenna connectors to the AirPort/Bluetooth card.
    • Remove the two 4.0 mm T5 Torx screws securing the four antenna connectors to the AirPort/Bluetooth card.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect all four antenna connectors by prying them straight up from their sockets on the AirPort/Bluetooth card. Disconnect all four antenna connectors by prying them straight up from their sockets on the AirPort/Bluetooth card. Disconnect all four antenna connectors by prying them straight up from their sockets on the AirPort/Bluetooth card.
    • Disconnect all four antenna connectors by prying them straight up from their sockets on the AirPort/Bluetooth card.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Gently pull the right speaker cable connector parallel to the logic board, straight out of its socket on the logic board. Gently pull the right speaker cable connector parallel to the logic board, straight out of its socket on the logic board.
    • Gently pull the right speaker cable connector parallel to the logic board, straight out of its socket on the logic board.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat edge of a spudger to pry the headphone jack cable connector from its socket on the logic board. Push the cable slightly to the right. Push the cable slightly to the right.
    • Use the flat edge of a spudger to pry the headphone jack cable connector from its socket on the logic board.

    • Push the cable slightly to the right.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Peel off the tape covering the exhaust duct.
    • Peel off the tape covering the exhaust duct.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Remove the following T8 Torx screws securing the exhaust duct to the rear enclosure:
    • Remove the following T8 Torx screws securing the exhaust duct to the rear enclosure:

    • Two 6.2 mm screws

    • Two 4.7 mm screws

  12. Este paso está sin traducir. Ayuda a traducirlo

    Use the tip of a spudger to flip open the retaining flap on the microphone ribbon cable ZIF socket. Be sure you are prying up on the hinged retaining flap, not the socket itself. Gently pull the microphone ribbon cable straight out of its socket.
    • Use the tip of a spudger to flip open the retaining flap on the microphone ribbon cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

    • Gently pull the microphone ribbon cable straight out of its socket.

  13. Este paso está sin traducir. Ayuda a traducirlo

    Remove the four 7.3 mm T8 Torx screws securing the logic board to the rear enclosure.
    • Remove the four 7.3 mm T8 Torx screws securing the logic board to the rear enclosure.

  14. Este paso está sin traducir. Ayuda a traducirlo

    Tilt the top of the logic board away from the rear enclosure. When removing and installing the logic board, take care not to damage the delicate microphone ribbon cable at the bottom left. Lift the logic board straight up and out of the iMac.
    • Tilt the top of the logic board away from the rear enclosure.

    • When removing and installing the logic board, take care not to damage the delicate microphone ribbon cable at the bottom left.

    • Lift the logic board straight up and out of the iMac.

    • Be careful not to snag the board on any of the rear enclosure's screw posts.

  15. Este paso está sin traducir. Ayuda a traducirlo

    When reassembling your iMac, be sure to align the exterior I/O ports correctly. The logic board can sit crooked even when secured with all its screws. Use a USB flash drive and/or ethernet cable to ensure the logic board is aligned correctly while you screw it in.
    • When reassembling your iMac, be sure to align the exterior I/O ports correctly. The logic board can sit crooked even when secured with all its screws.

    • Use a USB flash drive and/or ethernet cable to ensure the logic board is aligned correctly while you screw it in.

Linea de Meta

Adam O'Camb

Miembro Desde 11/04/15

145,759 Reputación

417 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

138 Miembros

16,998 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 53