Saltar al contenido principal

Introducción

Use this guide to replace a faulty MagSafe DC-In board.

    • Remove the following ten screws securing the lower case to the upper case:

    • Two 2.3 mm Pentalobe screws

    • Eight 3.0 mm Pentalobe screws

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

    For all the screws you use the P5 pentalobe screwdriver?

    Carlos - Contestar

    Pentalobe is only for the screws on the bottom cover. The Torx screw driver is for the remainder.

    Fredrik -

    Is the Pentalobe screwdriver mentioned in the tools list? I did not have one so I used a filed down flat blade screwdriver. Not a fantastic idea, but it works.

    Alex Birkett - Contestar

    Yes, it's mentioned on the top of this page. P5 Pentalobe to be precise. I didn't have one either, so I bought one from iFixit and that works fantastic. An absolutely precise fit, which is important especially when you might open your MacBook a couple of times during the years you own it. Not using the correct tool might do more harm to the screws than you want! I once had this with a Lenovo Yoga 3 Pro, which has Torx screws (T4 I think) and I used cheap Chinese quality tools, with the result that both the tool and one of the screws are damaged.

    addvariety -

    the macbook in the picture is 2012. does it has the same structure as 2013?

    Edison - Contestar

    I never, ever, ever considered using anything but the correct tool on the Pentalobe screws. Too easy to strip and void your warranty (if still in effect), as well as make it almost impossible to get inside later for another upgrade or repair. The Wiha P5 Pentalobe screwdriver fits like a glove and costs only about $11 (a fraction of your drive's price)at Amazon.com. Get it!

    marketing - Contestar

    is P5 supposed to be for all 10 screws? it works on the 2x 2.3mm at the top, but not for the 8x others for me. what size screwdriver for the 3mm? thanks

    monsieurescargot - Contestar

    Yes, the p5 works for all 10 pentalobe screw heads for bottom cover. The the different size mm reference only refers to the difference in length of the screws, but again both heads are p5.

    Antoine Thornton - Contestar

    I followed this exactly and was able to replace my broken trackpad. I did not have to replace the ribbon OR the battery. However I would suggest getting the ribbon since it’s fairly cheap, as for the batteries I was able to do it with a card only. I didn’t use any heat or the liquid but it takes some time. You really have to work the card in there to release the glue. Also you must be very careful not to bend the batteries or damage them, if you do you must replace with new. This took me about 1.5hrs and my computer works like new. Apple cost for this job was around $450, I did it for $120. Big ups to ifixit for this awesome tutorial, tool set and parts!

    On a side note, only use quality tools, the cheap ones will break or strip the screws.

    Dustin Steward - Contestar

    Note that the eight 3mm screws have a shoulder under the head, while the two 2.3mm screws are “full thread”, i.e., there is no shoulder under their heads. It’s important to put the two screws with no shoulder at the hinge of the cover.

    All ten screws require a P5 Pentalobe screwdriver, preferably with a magnetized tip to help hold and position the screw.

    All of the screws have blue “Loctite” thread locker compound on their threads. This is to help prevent the screws from working loose and falling out. Don’t attempt to clean the Loctite from the screws — leave it in place, and it will continue to help prevent the re-inserted screws from working loose.

    When replacing the bottom cover, it is a good technique to insert and BEGIN tightening all ten screws BEFORE fully tightening any one screw. After all the screws have been started, then go around and finish tightening all of them. By doing this, you make it easier to feel that each screw has been started properly, and is not “cross-threaded”.

    doubleclutch - Contestar

    This is what I found on my MBP mid-2014 13” Retina. All 10 used the same screwdriver. I didn’t see the blue “loctite” but I also got my computer refurbished.

    Evan Shulman -

    A good technique for starting to thread the screws when replacing them is to position and align the screw, and with the driver, gently turn the screw in the REMOVAL direction until you feel and hear a slight click. This click happens when the leading thread of the screw drops off of the leading edge of the thread in the hole — this is the point at which the threads are properly positioned for engagement. You can now turn the driver and screw in the TIGHTENING direction. This technique will help prevent accidental “cross-threading” of the screw, which will damage the threads permanently.

    Note that this is a useful technique when installing ANY threaded fastener.

    doubleclutch - Contestar

    Just finished replacing my battery (MacBook Pro 13” early 2015), glad I did, the old ones were noticeably swollen. I was surprised to find the battery at 57% upon completion and charging the new battery. No problems with replacement however, kit arrived without the Pentalobe driver. I got a nice complete kit from Amazon for 20 euro in 2 days. iFixit offered a coupon on any future purchase but right now, I have no plans on needing anything. Nice gesture but would have preferred the driver in the kit in the first place.

    Suggest having a small can of compressed air on hand to clean out the interior, after 4 years, mine was quite dirty. Ear buds and alcohol were the best I could do. And a magnetized driver is mandatory I think.

    D M - Contestar

    REQUIRED PARTS (SCREWS) TO DO THIS JOB UNAVAILABLE HERE:

    If your keyboard is riveted to the chassis as mine is, Late 2013 MBP 13” retina, you need about 100 screws to reattach the new keyboard.

    ifixit does not have them. I did just now find them at Beetstech for $4.50 along with a back light $13 for the keyboard in case you want one. It looks like Beetstech is a big competitor of ifixit with an excellent reputation (like ifixit has) too. I just ordered these parts and will not happily be moving forward with my keyboard replacement.

    Timothy Hardman - Contestar

  1. Wedge your fingers between the upper case and the lower case.
    • Wedge your fingers between the upper case and the lower case.

    • Gently pull the lower case away from the upper case to remove it.

    This takes a bit more effort than you might expect. Put your fingers where shown and lift about 3inches. With enough upwards pressure the plastic holders will “pop free” and the bottom will come off easily.

    hamiltont - Contestar

    Agreed. A decent amount of force is required here.

    Evan Shulman - Contestar

  2. The lower case is connected to the upper case with two plastic clips near its center. During reassembly, gently push down the center of the lower case to reattach the two plastic clips.
    • The lower case is connected to the upper case with two plastic clips near its center.

    • During reassembly, gently push down the center of the lower case to reattach the two plastic clips.

    There are two screws that are shorter-they go to the back near the vent.

    wrbandllm - Contestar

    This was already mentioned at the start, it says 2x 2.3mm screws and those are coloured red instead of orange for the other ones in iFixit's image.

    addvariety - Contestar

    What is the black vinyl-y sticker on the inside of the case (some sort of shield?). I was forced to slightly puncture it in order to replace the feet on my laptop. Thanks in advance.

    Tommy Huang - Contestar

    When I got the back off, I found this piece loose, any idea what it is? about 9mm long frosted plastic

    https://imgur.com/a/tYaxGdG

    Fred Anderson - Contestar

    This wording I found quite confusing. They just mean when putting the lid back on that you just removed in the previous step, push here.

    Mmm ttt - Contestar

    I took my pointer and thumb (which are luckily long enough) to feel where the studs are on the back panel, and then as I put the back panel back on, I pushed in the spot I had marked with my fingers to ensure I was applying pressure only on this part.

    Evan Shulman - Contestar

  3. If necessary, remove the plastic cover adhered to the battery contact board.
    • If necessary, remove the plastic cover adhered to the battery contact board.

    Do you know where I can purchase this plastic cover? Mine is missing and no one will work on my computer without it.

    jodieabc - Contestar

    There is no point on going near the battery or logic board. I cut out these steps with no issue. It is precautionary but unnecessary.

    Jaime Leonard - Contestar

    I replaced both my L and R speakers on my MBP mid-2014 13” withOUT doing this step.

    Evan Shulman - Contestar

    My new battery kit included a replacement for this part, so, no need to save the old one.

    Ralph Begleiter - Contestar

  4. Kits de Reparación de Android

    Estás a un kit de tu nueva pantalla o batería.

    Comprar Ahora

    Kits de Reparación de Android

    Estás a un kit de tu nueva pantalla o batería.

    Comprar Ahora
  5. Use the flat end of a spudger to lift the battery connector straight up out of its socket on the logic board. Be sure you lift up only on the connector itself, not the socket, or you risk permanent damage to the logic board.
    • Use the flat end of a spudger to lift the battery connector straight up out of its socket on the logic board.

    • Be sure you lift up only on the connector itself, not the socket, or you risk permanent damage to the logic board.

    I have a friends MacBook Pro that has some water damage that caused the MacBook not to be able to use battery power, but still work when plugged into A/C. Upon further inspection I can see visible corrosion on a few of the 9 cables going from the battery connector to that small circuit board. Is it possible to just replace that circuit board?

    jramsey21 - Contestar

    I have the some problem. I was thinking to replace the whole battery but I am not it will solve the problem. Any suggestions?

    salvatorebarbera -

    Sometimes it can be enough to just clean the contacts without having to replace the entire board. Dosent work for complicated IC's like plcc type, where corrosion is underneath the chip. Here you will have to reheat and reapply the IC.

    andrehedegaard -

    Hi,have you find the solution for your battery? I also have same problem, run with plugs but it battery not supporting… as soon the plug of it goes off

    Jewel Rahman -

    Have either of you replaced the battery and/or circuit board to fix the MacBooks with the water damage ? I have the same problem with the MacBook working fine when connected to power but dying immediately when the power cord is removed.

    Steve - Contestar

    Hi, Steve. I had the same problem: Macbook Pro 15 retina with coffee damage. And it worked fine when connected to power. I made it working after replacing the whole battery. It seems that circuit connected to the battery becomes disabled to prevent short circuit.

    Vadim Gribanov -

    When placing the battery connector back into the socket on the logic board, check that every part of connector is pressed down. You should hear a soft click when it's back in place.

    Ethan Tarquin - Contestar

    Thanks for the comment. My MBP isn’t powering on after I walked through these steps, and I assume it is because the battery connector isn’t fully connected. (I can’t check yet since I borrowed the pentalobe screwdriver)

    Caleb Steinborn -

    +1

    I thought I made sure it was connected but when running the computer it only detected the battery but couldn’t power it. I had to run with power adapter. Also it didn’t charge. I guess some pins were connected but not all. To verify that all were connected I removed the plastic cover, placed it carefully completely flat, and then reattached the plastic cover. After that it worked!

    Jonas Ehrs -

    If I only want to replace the trackpad cable, then which steps should I skip? This step seems unnecessary

    Parth Gudhka - Contestar

    Removing the battery connector took a bit of finagling. It wasn’t as easy as one would think. Be very careful when doing this as they warn to not damage it. Otherwise great instructions!!!!

    Peppon - Contestar

    I replaced both my L and R speakers on my MBP mid-2014 13” withOUT doing this step.

    Evan Shulman - Contestar

    I have verified I have this battery, and I have a mid-2014 macbook retina. And I swear i do not see this battery connector. I didn’t take the cover off, per other comments that said it was an unnecessary risk. What the heck? will I not see the battery cable without taking of that cover?

    martha - Contestar

    How can i post a photo of what I am seeing …I don’t see the battery connector! not like in photo above. maybe I have to remove that plastic cover although others recommended not doing that (see above).

    martha - Contestar

    ooops nevermind..I see it now! tks . But..there is SO much gunk/dust under there (old, hand me down, used by my teen daughter while eating in bed no doubt!) . Should I attempt to clean? Beyond just blowing on it? Is compressed air safe? Or should I just leave it be? Assuming I don’t break it while replacing this battery I’d like not to break it otherwise! tks

    martha - Contestar

  6. Bend the battery connector up out of the way to prevent accidental contact with its socket during your repair.
    • Bend the battery connector up out of the way to prevent accidental contact with its socket during your repair.

    If you miss or let this step for later like I did, the power left in the battery even though the computer is completely shut down, will screw up the I/O board cable like I did. I noticed this after I put all the pieces back, turn the computer on and surprise, no wifi hardware is detected. -.-

    sebasgaes - Contestar

    Not sure I understand: did leaving the battery plugged in permanently broke the I/O board (or anything else)?

    Adrien Izzet -

    I put a small piece of blue painters tape on the battery connector contacts to prevent it from accidentally making a connection and shorting. This helped keep things a bit more protected.

    LaymanLab - Contestar

    That’s a great idea!

    David Lilliebridge - Contestar

    I used a small piece of paper to prevent the connector from connecting, no need to wrestle with even low-stick adhesive.

    dbrick - Contestar

    I replaced both my L and R speakers on my MBP mid-2014 13” withOUT doing this step.

    Evan Shulman - Contestar

    I agree that inserting a small paper above between the socket and the connector was useful. I used post-it-note, but kept the adhesive away from the socket.

    Ralph Begleiter - Contestar

  7. Grab the black plastic tab to flip the display cable connector open and pull it straight out of its socket on the logic board. Pull in the direction of the cable, parallel to the logic board. Do not pull up. Pull in the direction of the cable, parallel to the logic board. Do not pull up.
    • Grab the black plastic tab to flip the display cable connector open and pull it straight out of its socket on the logic board.

    • Pull in the direction of the cable, parallel to the logic board. Do not pull up.

    I managed to just move the cable without having to disconnect whilst replacing my MagSafe connector

    lewismacqueen - Contestar

    Pull straight OUT not up.

    Mmm ttt - Contestar

  8. Pull the DC-In board connector straight out of its socket on the logic board. Pull the DC-In board connector straight out of its socket on the logic board.
    • Pull the DC-In board connector straight out of its socket on the logic board.

  9. Remove the two 3.5 mm T5 Torx screws securing the MagSafe DC-In board to the upper case.
    • Remove the two 3.5 mm T5 Torx screws securing the MagSafe DC-In board to the upper case.

    • You may need to gently push the display cable out of the way to expose the screws.

  10. Use the MagSafe DC-In board cable to pull the board out and up from the upper case to remove it. Use the MagSafe DC-In board cable to pull the board out and up from the upper case to remove it. Use the MagSafe DC-In board cable to pull the board out and up from the upper case to remove it.
    • Use the MagSafe DC-In board cable to pull the board out and up from the upper case to remove it.

    Before tightening the screws on the DC board, it helps to push it slightly outwards so that it seats against the case.

    Russell Hodin - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

14 personas más completaron esta guía.

Sam Goldheart

Miembro Desde 18/10/12

388,210 Reputación

545 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

107 Miembros

9,417 Guías creadas

How can I know if the magsafe is not working ?

lpelaez - Contestar

Thanks for great tutorial!

Yep, what are the signs of bad dc-in board?

When I plug in the charger, LED on magsafe connector doesn't light up.

AC Charger Information:

Connected: Yes

ID: 0x0000

Revision: 0x0000

Family: 0x0000

Serial Number: 0x00000000

Charging: No

For some reason charging doesn't start, my battery has only 600 cycles on it.

Can you guys help?

P.S. I tried plugging other adapters thats working, same thing (

Olga Kolina - Contestar

I Have replaced the battery and the machine still works under the power from the new battery but the LED won’t come on the magsafe charger. Now I have replaced the DC In board and still not charging. the charger works on the other Mac in the house. What could the issue be?

Christopher Culler - Contestar

Añadir comentario

Ver Estadísticas:

Past 24 Hours: 1

Past 7 Days: 20

Past 30 Days: 175

Global: 10,398