Saltar al contenido principal

Introducción

Use this guide to replace the I/O board, including the headphone jack, USB port, and MagSafe 2 port, in your MacBook Air 13" Early 2017.

    • Before proceeding, power down your MacBook. Close the display and lay it on a soft surface, top-side down.

    • Use a P5 Pentalobe driver to remove ten screws securing the lower case, of the following lengths:

    • Two 9 mm screws

    • Eight 2.6 mm screws

  1. MacBook Air 13" Early 2017 I/O Board Replacement: paso 2, imagen 1 de 1
    • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

    • Remove the lower case and set it aside.

  2. MacBook Air 13" Early 2017 I/O Board Replacement, Battery Connector: paso 3, imagen 1 de 2 MacBook Air 13" Early 2017 I/O Board Replacement, Battery Connector: paso 3, imagen 2 de 2
    • To ensure that everything is de-energized and won't turn on while you're working, it is recommended that you disconnect the battery.

    • Grab the clear plastic pull tab attached to the battery connector and pull it parallel to the board toward the front edge of the Air.

    • Do not lift upward on the connector as you disconnect it or you risk damage to the connector socket.

  3. MacBook Air 13" Early 2017 I/O Board Replacement, I/O Board Cable: paso 4, imagen 1 de 1
    • Use the flat end of a spudger to pry the I/O board cable connector up out of its socket on the I/O board.

  4. MacBook Air 13" Early 2017 I/O Board Replacement: paso 5, imagen 1 de 1
    • Carefully peel the I/O board cable from the adhesive securing it to the top of the fan.

    • During reassembly, make sure this cable is in the correct orientation. It will fit if reversed, but the laptop will not boot.

  5. MacBook Air 13" Early 2017 I/O Board Replacement: paso 6, imagen 1 de 2 MacBook Air 13" Early 2017 I/O Board Replacement: paso 6, imagen 2 de 2
    • The following connector has an especially deep socket. Use care when disconnecting it.

    • While gently pulling the I/O board cable upward near its connection to the logic board, use the flat end of a spudger to pry up on alternating sides of the connector to help "walk" it out of its socket.

    • Remove the I/O board cable.

  6. MacBook Air 13" Early 2017 I/O Board Replacement, Fan: paso 7, imagen 1 de 1
    • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

  7. MacBook Air 13" Early 2017 I/O Board Replacement: paso 8, imagen 1 de 1
    • Peel the rubber gasket off the adhesive on the top of the fan.

  8. MacBook Air 13" Early 2017 I/O Board Replacement: paso 9, imagen 1 de 1
    • Remove the following three screws securing the fan to the upper case:

    • One 5.2 mm T5 Torx screw

    • One 3.3 mm T5 Torx screw

    • One 4.4 mm T5 Torx screw with a short head

  9. MacBook Air 13" Early 2017 I/O Board Replacement: paso 10, imagen 1 de 2 MacBook Air 13" Early 2017 I/O Board Replacement: paso 10, imagen 2 de 2
    • Lift the fan from the I/O board side and pull it free from the upper case.

    • Removing the fan will also disconnect the fan ribbon cable. Be careful not to snag it.

  10. MacBook Air 13" Early 2017 I/O Board Replacement, I/O Board: paso 11, imagen 1 de 1
    • Disconnect the I/O board by pulling its power cable away from its socket on the logic board.

    • Pull the cable parallel to the face of the logic board toward the right edge of the Air.

  11. MacBook Air 13" Early 2017 I/O Board Replacement: paso 12, imagen 1 de 2 MacBook Air 13" Early 2017 I/O Board Replacement: paso 12, imagen 2 de 2
    • Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.

    • Pry up from beneath the wires.

  12. MacBook Air 13" Early 2017 I/O Board Replacement: paso 13, imagen 1 de 2 MacBook Air 13" Early 2017 I/O Board Replacement: paso 13, imagen 2 de 2
    • Use the tip of a spudger to carefully flip up the retaining flap on the microphone ribbon cable ZIF socket.

    • Make sure you are flipping up the retaining flap, not the socket itself.

  13. MacBook Air 13" Early 2017 I/O Board Replacement: paso 14, imagen 1 de 1
    • Remove the single 4.1 mm T5 Torx screw securing the I/O board to the upper case.

  14. MacBook Air 13" Early 2017 I/O Board Replacement: paso 15, imagen 1 de 2 MacBook Air 13" Early 2017 I/O Board Replacement: paso 15, imagen 2 de 2
    • Gently de-route the camera cable from its notch on the I/O board and push it out of the way with the tip of a spudger.

  15. MacBook Air 13" Early 2017 I/O Board Replacement: paso 16, imagen 1 de 1
    • Lift the I/O board from the logic board side and pull it free from the upper case.

    • Removing the I/O board will also disconnect the microphone ribbon cable. Be careful not to snag it.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

11 personas más completaron esta guía.

Adam O'Camb

Miembro Desde 11/04/15

170,107 Reputación

418 Guías creadas

2 comentarios

Can this part repair the problem of not detecting microphone and speakers?

Daniel Guinto Sanchez - Contestar

Replacing this board fixed my audio issues!

ChickenBacon -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 10

Ultimos 7 días: 91

Ultimos 30 días: 440

Todo El Tiempo: 6,528