Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Coloca un dedo en el borde superior del conjunto de la cubierta del compartimento y desliza el conjunto hacia la parte delantera del Vive hasta que se suelte del auricular.
-
Levanta la tapa para separarla del auricular y deslízala hacia arriba por los cables hasta que quede fuera del camino.
-
-
-
Levanta el cable HDMI hacia arriba para desenchufarlo del auricular.
-
-
-
Repite el proceso de levantar y desenchufar con el resto de los cables USB, de alimentación y de audio.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a T5 Torx driver to remove the two 12 mm-long screws securing the head strap mounts on either side of the headset.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the facerest straight away from the headset to remove it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to remove the small stickers over the four screws securing the outer shell.
-
Use a T5 Torx driver to remove the four 3.4 mm-long screws securing the outer shell.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the top edge of the right half of the outer shell, behind the component cover and near the seam in the center. Pull it to the right and upward, away from the headset to release the clip securing that part of the shell.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the right half the outer shell and pull it to the right and toward the front of the headset in a twisting motion until you feel the clips on the front of the cover release.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the right side of the outer shell to the right and off of the headset.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Repeat the last three steps for the left side of the outer shell and remove it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to remove the clear tape over all four of the sensor array cable connectors.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the pointed end of a spudger to flip up the small locking flap on one of the sensor array ZIF connectors.
-
Slide the cable straight out of its socket on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Repeat the previous step for the remaining three sensor array cables to disconnect the remaining cables.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers or a spudger to pry up the camera cable cover and remove it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the camera cable connector straight up from its socket on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a PH000 driver to remove the five 3.9 mm screws securing the sensor array.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a PH000 driver to remove the four 3.9 mm screws securing the sensor array.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Phillips #000 Screwdriver$5.49-
Use a PH000 driver to remove the four 3.9 mm screws securing the sensor array.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the sensor array away from the headset to remove it.
-
Cancelar: No complete esta guía.
3 personas más completaron esta guía.