Saltar al contenido principal
  1. Este paso está sin traducir. Ayuda a traducirlo

    Be sure to power down and disconnect your Vive before beginning. Place a finger on the top edge of the compartment cover assembly and slide the assembly toward the front of the Vive until it comes loose from the headset. Lift the cover away from the headset and slide it up the cables until it's out of the way.
    • Be sure to power down and disconnect your Vive before beginning.

    • Place a finger on the top edge of the compartment cover assembly and slide the assembly toward the front of the Vive until it comes loose from the headset.

    • Lift the cover away from the headset and slide it up the cables until it's out of the way.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Lift the HDMI cable straight up to unplug it from the headset. Lift the HDMI cable straight up to unplug it from the headset.
    • Lift the HDMI cable straight up to unplug it from the headset.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Repeat the lifting and unplugging process with the remaining USB, power, and audio cables. Repeat the lifting and unplugging process with the remaining USB, power, and audio cables. Repeat the lifting and unplugging process with the remaining USB, power, and audio cables.
    • Repeat the lifting and unplugging process with the remaining USB, power, and audio cables.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Be sure to power down and disconnect your Vive before beginning. Use a T5 Torx driver to remove the two 12 mm-long screws securing the head strap mounts on either side of the headset.
    • Be sure to power down and disconnect your Vive before beginning.

    • Use a T5 Torx driver to remove the two 12 mm-long screws securing the head strap mounts on either side of the headset.

    • The mounts may fall off when the screws are removed, so be careful not to lose any parts.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Remove both head strap mounts. Remove both head strap mounts. Remove both head strap mounts.
    • Remove both head strap mounts.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Slide the facerest straight away from the headset to remove it. Slide the facerest straight away from the headset to remove it.
    • Slide the facerest straight away from the headset to remove it.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Use tweezers to remove the small stickers over the four screws securing the outer shell. Use a T5 Torx driver to remove the four 3.4 mm-long screws securing the outer shell. Use a T5 Torx driver to remove the four 3.4 mm-long screws securing the outer shell.
    • Use tweezers to remove the small stickers over the four screws securing the outer shell.

    • Use a T5 Torx driver to remove the four 3.4 mm-long screws securing the outer shell.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Grasp the top edge of the right half of the outer shell, behind the component cover and near the seam in the center. Pull it to the right and upward, away from the headset to release the clip securing that part of the shell. Grasp the top edge of the right half of the outer shell, behind the component cover and near the seam in the center. Pull it to the right and upward, away from the headset to release the clip securing that part of the shell. Grasp the top edge of the right half of the outer shell, behind the component cover and near the seam in the center. Pull it to the right and upward, away from the headset to release the clip securing that part of the shell.
    • Grasp the top edge of the right half of the outer shell, behind the component cover and near the seam in the center. Pull it to the right and upward, away from the headset to release the clip securing that part of the shell.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Grasp the right half the outer shell and pull it to the right and toward the front of the headset in a twisting motion until you feel the clips on the front of the cover release. Grasp the right half the outer shell and pull it to the right and toward the front of the headset in a twisting motion until you feel the clips on the front of the cover release.
    • Grasp the right half the outer shell and pull it to the right and toward the front of the headset in a twisting motion until you feel the clips on the front of the cover release.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Slide the right side of the outer shell to the right and off of the headset. Slide the right side of the outer shell to the right and off of the headset.
    • Slide the right side of the outer shell to the right and off of the headset.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Repeat the last three steps for the left side of the outer shell and remove it. Repeat the last three steps for the left side of the outer shell and remove it.
    • Repeat the last three steps for the left side of the outer shell and remove it.

  12. Este paso está sin traducir. Ayuda a traducirlo

    Use tweezers to remove the clear tape over all four of the sensor array cable connectors. Use tweezers to remove the clear tape over all four of the sensor array cable connectors. Use tweezers to remove the clear tape over all four of the sensor array cable connectors.
    • Use tweezers to remove the clear tape over all four of the sensor array cable connectors.

  13. Este paso está sin traducir. Ayuda a traducirlo

    Use the pointed end of a spudger to flip up the small locking flap on one of the sensor array ZIF connectors. Slide the cable straight out of its socket on the motherboard. Slide the cable straight out of its socket on the motherboard.
    • Use the pointed end of a spudger to flip up the small locking flap on one of the sensor array ZIF connectors.

    • Slide the cable straight out of its socket on the motherboard.

  14. Este paso está sin traducir. Ayuda a traducirlo

    Repeat the previous step for the remaining three sensor array cables to disconnect the remaining cables. Repeat the previous step for the remaining three sensor array cables to disconnect the remaining cables. Repeat the previous step for the remaining three sensor array cables to disconnect the remaining cables.
    • Repeat the previous step for the remaining three sensor array cables to disconnect the remaining cables.

  15. Este paso está sin traducir. Ayuda a traducirlo

    Use tweezers or a spudger to pry up the camera cable cover and remove it. Use tweezers or a spudger to pry up the camera cable cover and remove it.
    • Use tweezers or a spudger to pry up the camera cable cover and remove it.

  16. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat end of a spudger to pry the camera cable connector straight up from its socket on the motherboard. Use the flat end of a spudger to pry the camera cable connector straight up from its socket on the motherboard.
    • Use the flat end of a spudger to pry the camera cable connector straight up from its socket on the motherboard.

  17. Este paso está sin traducir. Ayuda a traducirlo

    Use a PH000 driver to remove the five 3.9 mm screws securing the sensor array.
    • Use a PH000 driver to remove the five 3.9 mm screws securing the sensor array.

  18. Este paso está sin traducir. Ayuda a traducirlo

    Use a PH000 driver to remove the four 3.9 mm screws securing the sensor array.
    • Use a PH000 driver to remove the four 3.9 mm screws securing the sensor array.

  19. Este paso está sin traducir. Ayuda a traducirlo

    • Use a PH000 driver to remove the four 3.9 mm screws securing the sensor array.

    • You'll need a narrow, long-shaft driver to reach these screws.

  20. Este paso está sin traducir. Ayuda a traducirlo

    Lift the sensor array away from the headset to remove it. Lift the sensor array away from the headset to remove it.
    • Lift the sensor array away from the headset to remove it.

  21. Este paso está sin traducir. Ayuda a traducirlo

    Remove the tape covering the interconnect cable socket. Use the point of a spudger to flip up the small locking flap on the cable socket. Slide the interconnect cable straight out of its socket on the motherboard.
    • Remove the tape covering the interconnect cable socket.

    • Use the point of a spudger to flip up the small locking flap on the cable socket.

    • Slide the interconnect cable straight out of its socket on the motherboard.

  22. Este paso está sin traducir. Ayuda a traducirlo

    Remove the tape covering the left OLED cable socket. Use the point of a spudger to flip up the small locking flap on the cable socket. Slide the left OLED cable straight out of its socket on the motherboard.
    • Remove the tape covering the left OLED cable socket.

    • Use the point of a spudger to flip up the small locking flap on the cable socket.

    • Slide the left OLED cable straight out of its socket on the motherboard.

  23. Este paso está sin traducir. Ayuda a traducirlo

    Remove the tape covering the right OLED cable socket. Use the point of a spudger to flip up the small locking flap on the cable socket. Slide the right OLED cable straight out of its socket on the motherboard.
    • Remove the tape covering the right OLED cable socket.

    • Use the point of a spudger to flip up the small locking flap on the cable socket.

    • Slide the right OLED cable straight out of its socket on the motherboard.

  24. Este paso está sin traducir. Ayuda a traducirlo

    Use a pair tweezers to slightly twist the interconnect cable and press it down until the tabs on either side of the cable clear the hole in the motherboard. During reassembly, make sure to thread the interconnect cable through its slot in the motherboard.
    • Use a pair tweezers to slightly twist the interconnect cable and press it down until the tabs on either side of the cable clear the hole in the motherboard.

    • During reassembly, make sure to thread the interconnect cable through its slot in the motherboard.

  25. Este paso está sin traducir. Ayuda a traducirlo

    Press the non-port-end of the motherboard toward the top of headset while hinging it away from the midframe to free it from the clips securing that end. Slide the motherboard toward the bottom of the headset, over the clips, to remove it. Take care not to snag any cables during removal.
    • Press the non-port-end of the motherboard toward the top of headset while hinging it away from the midframe to free it from the clips securing that end.

    • Slide the motherboard toward the bottom of the headset, over the clips, to remove it.

    • Take care not to snag any cables during removal.

  26. Este paso está sin traducir. Ayuda a traducirlo

    Use a pair of tweezers to peel back the plastic covering the eyepiece midframe cable socket. Use the pointed end of a spudger to flip up the plastic locking flap on the socket. Slide the cable straight out of its socket to remove it.
    • Use a pair of tweezers to peel back the plastic covering the eyepiece midframe cable socket.

    • Use the pointed end of a spudger to flip up the plastic locking flap on the socket.

    • Slide the cable straight out of its socket to remove it.

  27. Este paso está sin traducir. Ayuda a traducirlo

    Gently peel the eyepiece midframe cable off of the facerest midframe. Gently peel the eyepiece midframe cable off of the facerest midframe.
    • Gently peel the eyepiece midframe cable off of the facerest midframe.

  28. Este paso está sin traducir. Ayuda a traducirlo

    Use a PH000 driver to remove the four 3.9 mm screws securing the facerest midframe.
    • Use a PH000 driver to remove the four 3.9 mm screws securing the facerest midframe.

  29. Este paso está sin traducir. Ayuda a traducirlo

    Lift the facerest midframe off of the eyepiece midframe. Take care not to snag any cables during removal.
    • Lift the facerest midframe off of the eyepiece midframe.

    • Take care not to snag any cables during removal.

  30. Este paso está sin traducir. Ayuda a traducirlo

    Hinge the OLED and lens frames down and away from the focus knob end of the eyepiece midframe. Once you've rotated the OLED and lens frame about 90 degrees, push them straight down, parallel to the face of the eyepiece midframe, to separate them from the midframe. Once you've rotated the OLED and lens frame about 90 degrees, push them straight down, parallel to the face of the eyepiece midframe, to separate them from the midframe.
    • Hinge the OLED and lens frames down and away from the focus knob end of the eyepiece midframe.

    • Once you've rotated the OLED and lens frame about 90 degrees, push them straight down, parallel to the face of the eyepiece midframe, to separate them from the midframe.

  31. Este paso está sin traducir. Ayuda a traducirlo

    Gently lift the eyepiece gasket off of the lens and OLED frames to remove it. Gently lift the eyepiece gasket off of the lens and OLED frames to remove it. Gently lift the eyepiece gasket off of the lens and OLED frames to remove it.
    • Gently lift the eyepiece gasket off of the lens and OLED frames to remove it.

  32. Este paso está sin traducir. Ayuda a traducirlo

    Pull the rubber bumpers off of either end of the support rod. Pull the rubber bumpers off of either end of the support rod. Pull the rubber bumpers off of either end of the support rod.
    • Pull the rubber bumpers off of either end of the support rod.

  33. Este paso está sin traducir. Ayuda a traducirlo

    Slide the support rod out of its brackets on the lens and OLED frames. Slide the support rod out of its brackets on the lens and OLED frames. Slide the support rod out of its brackets on the lens and OLED frames.
    • Slide the support rod out of its brackets on the lens and OLED frames.

  34. Este paso está sin traducir. Ayuda a traducirlo

    Use a PH000 driver to remove the eight 3.1 mm screws securing the focus rod brackets.
    • Use a PH000 driver to remove the eight 3.1 mm screws securing the focus rod brackets.

  35. Este paso está sin traducir. Ayuda a traducirlo

    Remove the focus rod and its brackets.
    • Remove the focus rod and its brackets.

  36. Este paso está sin traducir. Ayuda a traducirlo

    Use a PH000 driver to remove the eight 2.4 mm screws securing the OLED covers.
    • Use a PH000 driver to remove the eight 2.4 mm screws securing the OLED covers.

  37. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat end of a spudger push up one edge of the OLED cover and start unclipping that edge. Use the flat end of a spudger push up one edge of the OLED cover and start unclipping that edge.
    • Use the flat end of a spudger push up one edge of the OLED cover and start unclipping that edge.

  38. Este paso está sin traducir. Ayuda a traducirlo

    Slide the spudger under the clip along that edge to free the rest of the edge. Slide the spudger under the clip along that edge to free the rest of the edge.
    • Slide the spudger under the clip along that edge to free the rest of the edge.

  39. Este paso está sin traducir. Ayuda a traducirlo

    Slide the spudger around the remaining edges of the OLED cover to unclip those edges. Slide the spudger around the remaining edges of the OLED cover to unclip those edges. Slide the spudger around the remaining edges of the OLED cover to unclip those edges.
    • Slide the spudger around the remaining edges of the OLED cover to unclip those edges.

  40. Este paso está sin traducir. Ayuda a traducirlo

    Remove the OLED cover. Repeat the last three steps to remove the other OLED cover.
    • Remove the OLED cover.

    • Repeat the last three steps to remove the other OLED cover.

    • During reassembly, remember to thread the OLED cables through their slots in the OLED cover.

  41. Este paso está sin traducir. Ayuda a traducirlo

    Very carefully lift the OLED display by its edges out of its frame.
    • Very carefully lift the OLED display by its edges out of its frame.

    • If you are reusing the OLED displays, be very careful to avoid touching the front of the displays or bending or cracking the displays.

    • Repeat this process for the other OLED display.

  42. Este paso está sin traducir. Ayuda a traducirlo

    Apply an iOpener to the lens to soften the adhesive securing it to the frame.
    • Apply an iOpener to the lens to soften the adhesive securing it to the frame.

  43. Este paso está sin traducir. Ayuda a traducirlo

    Use an opening tool to pry up the flat edge of the lens. If it's difficult to pry up, apply the iOpener for another 30 seconds to further soften the adhesive.
    • Use an opening tool to pry up the flat edge of the lens.

    • If it's difficult to pry up, apply the iOpener for another 30 seconds to further soften the adhesive.

  44. Este paso está sin traducir. Ayuda a traducirlo

    Remove the lens.
    • Remove the lens.

    • Repeat the last two steps to remove the other lens.

    • Only the lens and OLED frames remain.

    • During reassembly, make sure the convex side of the lens is facing away from the frame.

Linea de Meta

2 personas más completaron esta guía.

Adam O'Camb

Miembro Desde 11/04/15

149,789 Reputación

418 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

138 Miembros

15,634 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 9

Ultimos 7 días: 49

Ultimos 30 días: 142

Todo El Tiempo: 1,917