Introducción

In this guide we will disassemble and remove the power supply from an Apple TV 4K

  1. Use a spudger to pry the bottom panel off from the body. It is held on with clips on the inside, so you will need to make sure those are undone while opening.
    • Use a spudger to pry the bottom panel off from the body. It is held on with clips on the inside, so you will need to make sure those are undone while opening.

    • The panel is held onto the device tightly, so you may need to be a bit forceful to remove it.

  2. Remove the following screws using a T6 Torx screwdriver holding the heat sink assembly in. Four 10 mm screws
    • Remove the following screws using a T6 Torx screwdriver holding the heat sink assembly in.

    • Four 10 mm screws

    • Lift and remove the heat sink assembly from the device.

  3. Use plastic spudger to pull up on all three antenna connectors to remove them. Remove rubber piece from front side of device.
    • Use plastic spudger to pull up on all three antenna connectors to remove them.

    • Remove rubber piece from front side of device.

  4. ¡Envío gratuito para todos los pedidos de más de USD100 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda
  5. Unscrew the following screws holding the logic board in place using the T7 Torx:
    • Unscrew the following screws holding the logic board in place using the T7 Torx:

    • Two black 3 mm screws

    • Two silver 4 mm screws

  6. Use a spudger to pry up logic board. Try lifting it up from the front side. Remove logic board and set aside. Remove logic board and set aside.
    • Use a spudger to pry up logic board. Try lifting it up from the front side.

    • Remove logic board and set aside.

  7. Use a T7 Torx to remove the screws: Five 5mm screws Carefully flip the device upside down to remove the logic board/power supply mount.
    • Use a T7 Torx to remove the screws:

    • Five 5mm screws

    • Carefully flip the device upside down to remove the logic board/power supply mount.

  8. Undo the latch connecting the power connector to the power supply. Feed the wire though the logic board/power supply mount.
    • Undo the latch connecting the power connector to the power supply.

    • Feed the wire though the logic board/power supply mount.

  9. Using a T-7 Torx unscrew the two silver screws. Two 4mm silver screws The power connector piece on the other side will now be free and fall out.
    • Using a T-7 Torx unscrew the two silver screws.

    • Two 4mm silver screws

    • The power connector piece on the other side will now be free and fall out.

  10. Use a screwdriver with a T-7 Torx bit to remove the following screws: Five black 3mm screws lift the power supply out of it's mount.
    • Use a screwdriver with a T-7 Torx bit to remove the following screws:

    • Five black 3mm screws

    • lift the power supply out of it's mount.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Brian Gehring

Miembro Desde 04/10/18

259 Reputación

2 Guías creadas

Equipo

UW Stout, Team S6-G3, Ogden Fall 2018 Miembro de UW Stout, Team S6-G3, Ogden Fall 2018

UWSTOUT-OGDEN-F18S6G3

4 Miembros

6 Guías creadas

Ver Estadísticas:

Ultimas 24 Horas: 5

Últimos 7 Días: 17

Últimos 30 Días: 50

Todo El Tiempo: 166