Use the release tabs to remove the rear cover
  • Use the release tabs to remove the rear cover

Agregar Comentario

Remove any ComSlot II or PCI cards that may be installed and their risers.
  • Remove any ComSlot II or PCI cards that may be installed and their risers.

Agregar Comentario

Unplug the logic board connections to the PRAM battery and fan.
  • Unplug the logic board connections to the PRAM battery and fan.

  • Remove the PRAM battery from it's Velcro mounting.

  • Remove the four #0 Philips screws securing the hard drive and processor fan assembly.

  • Remove the hard drive and processor fan assembly.

Agregar Comentario

Remove the two T6 Torx screws securing the A/V input board.
  • Remove the two T6 Torx screws securing the A/V input board.

  • Remove the A/V Input board

Agregar Comentario

Remove the white plastic shield
  • Remove the white plastic shield

  • Remove the T6 torx screw securing the logic board to the frame.

Agregar Comentario

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Turn the TAM around with the front facing you. Use a spudger to gently loosen the speaker covers from their press-fit snaps. Remove the speaker covers.
  • Turn the TAM around with the front facing you.

  • Use a spudger to gently loosen the speaker covers from their press-fit snaps. Remove the speaker covers.

Agregar Comentario

Remove the six T6 torx screws securing the front case to the rear case.
  • Remove the six T6 torx screws securing the front case to the rear case.

Agregar Comentario

Gently pull the tabs toward the center to release the latches hold the front and back together. These tabs are fragile but release easily. Use caution. Lean the top forward and lift up to pull the front case from it's bottom latches. DO NOT TRY TO REMOVE THE FRONT CASE. It is still connected to the back case by several wires and cables.
  • Gently pull the tabs toward the center to release the latches hold the front and back together. These tabs are fragile but release easily. Use caution.

  • Lean the top forward and lift up to pull the front case from it's bottom latches.

  • DO NOT TRY TO REMOVE THE FRONT CASE. It is still connected to the back case by several wires and cables.

Agregar Comentario

Disconnect the pink and white backlight inverter cable and the black and white right speaker cable from behind the floppy disk drive on the right side. On the left side, disconnect the 50-pin SCSI ribbon cable, analog audio cable and power cable from the CD-ROM drive. Disconnect the black and white left speaker cable.
  • Disconnect the pink and white backlight inverter cable and the black and white right speaker cable from behind the floppy disk drive on the right side.

  • On the left side, disconnect the 50-pin SCSI ribbon cable, analog audio cable and power cable from the CD-ROM drive.

  • Disconnect the black and white left speaker cable.

  • Disconnect the flat, orange display data cable.

  • Open the top case to the left like a book. There will be one more 50-pin cable to disconnect from the front control panel board.

Agregar Comentario

The easiest method to remove the logic board is to remove it with the tuner card and cabling.
  • The easiest method to remove the logic board is to remove it with the tuner card and cabling.

  • Disconnect the five cables illustrated.

Agregar Comentario

Remove the T10 torx screw and extract the stiff wire cable brace from the left side
  • Remove the T10 torx screw and extract the stiff wire cable brace from the left side

Agregar Comentario

Carefully peel back the tape securing the cables to the white, plastic logic board cover. Pull the cables back to reveal the back side of the logic board.
  • Carefully peel back the tape securing the cables to the white, plastic logic board cover. Pull the cables back to reveal the back side of the logic board.

  • Remove the five T10 screws holding the logic and tuner boards to the back case.

Agregar Comentario

Lift the logic board from the left edge then straight up to remove it from the rear case. The logic board slides out of the cabling connector. The logic board slides out of the cabling connector.
  • Lift the logic board from the left edge then straight up to remove it from the rear case.

  • The logic board slides out of the cabling connector.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Dylan

Miembro Desde 04/02/13

351 Reputación

1 Guía escrita

Hi,

One of the member of my Forum is looking for the Bose subwoofer including the power cable. Have you an idee on where could he find it ?

Thx.

Raziel

vitalisfrance - Contestar

It's missing the step to remove the two torx screws on the upper back side, below the cover with all the holes, after Step 5

Deagol - Contestar

Dose anybody know what goes in the top-most chip slot that is empty? Is that for an L2 Cache chip?

garo211 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 11

Últimos 30 Días: 47

Todo El Tiempo: 6,655