Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

La Kenmore Elite HE3 es una secadora eléctrica con una capacidad de 7.2 pies cúbicos de Kenmore.

Preguntas 283 Ver todo

Kenmore dryer HE3 code E1

Dryer will only run for 2-3 mins on any cycle before shutting down. It throws a code E1. Any ideas?

Contestado! View the answer Yo también tengo este problema

Es esta una buena pregunta?

Puntuación 4

Comentarios:

My dryer does the same thing but does not show a code.is it still the thermistor.

- de

Agregar un comentario

Kits para Nintendo Switch

Una solución rápida para volver al juego

Comprar kits de Switch

Kits para Nintendo Switch

Una solución rápida para volver al juego

Comprar kits de Switch

3 Respuestas

Solución Elegida

frank, E1 is a Thermistor error. First of course disconnect the power. Then remove the lint filter screen. Remove the two screws from the bottom flange of the toe kick panel. Pull the toe kick panel out at the bottom, pull down, and remove the panel. Remove the screw from the lint duct bracket and remove the bracket. Remove the two screws from the lint duct and remove the duct. You'll find the white thermal fuse on your blower wheel housing, right beside it is the thermistor. Replacing it should eliminate E1. The Whirlpool part number is 8577274 and in the attached image the part is located at position 42

Block Image

Fue útil esta respuesta?

Puntuación 5

Comentarios:

He3 dryer control board burnt out replaced it got E1 code have replaced all sensors and new motor still E1 code anyone help

- de

You ever get this figured out. I'm having the same issue

- de

After all your work is complete, whatever you have done and whatever the problem may be, perform a factory rebooting. I don't know but it may be similar to a vehicles check engine light in that it comes on, you and your mechanic fix the car and all its problems but the check engine light may stay on UNTIL it gets reset. Could be a similar situation w/the dryer.

- de

Can we get a parts list to go along with the schmatic?

- de

Agregar un comentario
La respuesta fue originalmente a otra pregunta.

Sorry it's a thermister code. Check your wiring continuity to and from it. Could be a bad part.

Fue útil esta respuesta?

Puntuación 2

Comentarios:

Replaced it twice still e1

- de

Agregar un comentario

replaced my thermistor 2 times- still have e 1 code. any ideas?

Fue útil esta respuesta?

Puntuación 0

Comentarios:

I have the same problem after changing my electronic control board that I purchased from amazon. initial problem the unit would not heat up no flame or igniter glowing. after checking all items like thermal fuse and thermistor, gas coils i found heater relay not closing on electronic control. numbers all match up thinking my new electronic control may be bad.

- de

Check the heat exhaust for lint clogs and the outdoor lint screen on the side of the house or what have you. Mine hadn’t been unclogged when I replaced the thermistor and burned out the new one. Use a vacuum and screw driver or hanger to get everything unclogged. Just a warning, be prepared for an animal to be caught in the outside part of the vent 0.o

- de

I have a Kenmore HE3 and I have changed the fuse, thermister and 2 other parts and im still getting a P22 code after running for about 60secs?

- de

Agregar un comentario

Añadir tu respuesta

frank estará eternamente agradecido.
Ver Estadísticas:

Ultimas 24 horas: 10

Ultimos 7 días: 103

Ultimos 30 días: 411

Todo El Tiempo: 21,011