Introducción

Installing a tube.

Herramientas

Partes

Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.
  • Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.

Agregar Comentario

Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible. Push the axle screw to reveal the axle rod on the other side.
  • Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible.

  • Push the axle screw to reveal the axle rod on the other side.

Agregar Comentario

Using the Allen wrench, finish unscrewing the axle screw and pull it out.
  • Using the Allen wrench, finish unscrewing the axle screw and pull it out.

  • Hold the wheel when pulling out the axle rod so that the bike does not fall.

Agregar Comentario

Pull the wheel from the fork.
  • Pull the wheel from the fork.

Agregar Comentario

Look at your tire and determine the correct tube size by locating the number (formated ## x #.##) on the wall of the tire.
  • Look at your tire and determine the correct tube size by locating the number (formated ## x #.##) on the wall of the tire.

  • Bike tubes come with one of two standard valve types: presta and schrader. These guides show the installation of a tube with a presta valve.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Unscrew the cap covering the valve. Remove the spacer that holds the valve in place against the rim of the wheel. Open the valve by turning the nut and pressing the valve in to release air pressure from the tube.
  • Unscrew the cap covering the valve.

  • Remove the spacer that holds the valve in place against the rim of the wheel.

  • Open the valve by turning the nut and pressing the valve in to release air pressure from the tube.

Agregar Comentario

Slide the tire lever between the tire and the rim. Push down on the tire lever until the edge of the tire is higher than the edge of the rim. Insert a second tire lever adjacent to  the first.
  • Slide the tire lever between the tire and the rim.

  • Push down on the tire lever until the edge of the tire is higher than the edge of the rim.

  • Insert a second tire lever adjacent to the first.

  • Slowly work one tire lever around the rim until the whole tire is loose.

Agregar Comentario

Press the valve through the rim of the wheel. Remove the tube from the tire.
  • Press the valve through the rim of the wheel.

  • Remove the tube from the tire.

Agregar Comentario

Partially inflate the tube.
  • Partially inflate the tube.

Agregar Comentario

Push the valve through the rim. Push the tube into the tire all the way around the rim of the wheel.
  • Push the valve through the rim.

  • Push the tube into the tire all the way around the rim of the wheel.

Agregar Comentario

Push the bead of the tire back into place around the rim.
  • Push the bead of the tire back into place around the rim.

  • Make sure not to pinch the tube between the bead of the tire and the rim. Failure to do so may cause a pinch flat.

Agregar Comentario

Inflate the tube to the desired air pressure.
  • Inflate the tube to the desired air pressure.

  • A suggested range of air pressure is located on the wall of the tire (formatted ##-##psi).

Agregar Comentario

Close the valve and replace the cap. Close the valve and replace the cap.
  • Close the valve and replace the cap.

Agregar Comentario

Linea de Meta

Una persona más ha completado esta guía.

Sterling Grande

Miembro Desde 08/10/12

126 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 9-14, Amido Fall 2012 Miembro de Cal Poly, Team 9-14, Amido Fall 2012

CPSU-AMIDO-F12S9G14

4 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 6

Últimos 30 Días: 22

Todo El Tiempo: 1,511