Repara tus cosas Comunidad Tienda

여는 절차

Aviso: Estás editando una guía de requisitos previos. Cualquier cambio que realices afectará a todas las 13 guías que incluyen este paso.

Volver a la Guía
Inglés
Coreano
Paso 4
Opening Procedure: paso 0, imagen 1 de 3 Opening Procedure: paso 0, imagen 2 de 3 Opening Procedure: paso 0, imagen 3 de 3

  • Heat an iOpener and thread it through the arms of the Anti-Clamp.

  • You can also use a hair dryer, heat gun, or hot plate—but extreme heat can damage the display and/or internal battery, so proceed with care.

  • Fold the iOpener so it lays on the bottom edge of the iPhone.

  • Wait one minute to give the adhesive a chance to release and present an opening gap.

  • Insert an opening pick into the gap under the screen and the plastic bezel, not the screen itself.

  • If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.

  • Don't crank more than a quarter turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.

  • Skip the next three steps.

iOpener를 가열하여 안티-클램프의 팔에 끼워 넣습니다.

헤어 드라이어, 열선총 또는 핫 플레이트를 사용할 수도 있지만—과도한 열은 디스플레이 및/또는 내부 배터리를 손상할 수 있으므로 신중히 진행하세요.

iPhone 하단 가장자리에 놓이도록 iOpener를 접으세요.

접착제가 풀려서 틈이 생길 때까지 1분 정도 기다리세요.

스크린 자체가 아닌 스크린과 플라스틱 베젤 밑에 여는 픽을 끼우세요.

안티-클램프가 충분한 틈을 만들지 못하면 열을 더 가하고 핸들을 1/4 바퀴 돌리세요.

한 번에 1/4 바퀴 이상 돌리지 말고 매번 돌릴 때마다 1분 정도 기다리세요. 안티-클램프와 시간에 맡기세요.

다음 세 단계는 건너뛰세요.

[* black] [guide|25705|Heat an iOpener|new_window=true] and thread it through the arms of the Anti-Clamp.
[* icon_note] You can also use a [guide|157348|hair dryer|new_window=true], [guide|151116|heat gun|new_window=true], or hot plate—but extreme heat can damage the display and/or internal battery, so proceed with care.
[* black] Fold the iOpener so it lays on the bottom edge of the iPhone.
[* black] Wait one minute to give the adhesive a chance to release and present an opening gap.
-[* orange] Insert an opening pick into the gap under the screen and the plastic bezel, ***not the screen itself.***
+[* green] Insert an opening pick into the gap under the screen and the plastic bezel, ***not the screen itself.***
[* icon_note] If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.
[* icon_caution] Don't crank more than a quarter turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.
[* black] ***Skip the next three steps.***

Tus contribuciones son autorizadas bajo la licencia de código abierto de Creative Commons.