Menú

Tus configuraciones

Mi Mesa de Trabajo

Obtén acceso rápido a guías, partes y respuestas para tus dispositivos
Mi Carrito

Al parecer tu carrito está vacío

Visita Nuestra Tienda

iPod 2nd Generation Battery Replacement

Destacado

Escrito Por: iRobot (y otro participante)
  • Comentarios: 1
  • Favoritos: 8
  • Terminaciones: 12

Guía Destacada

Dificultad

Moderar

Pasos

10

Tiempo Requerido

Sugerir un tiempo??

Secciones

2

Banderas

1

Featured Guide

Guía Destacada

Esta guía ha sido valorada como excepcionalmente genial por el personal de iFixit.

Introducción

Battery not lasting long? Swap it out.

Herramientas

Comprar estas herramientas

Partes

  1. Before opening your iPod, ensure that the hold switch is in the locked position.

    • Before opening your iPod, ensure that the hold switch is in the locked position.

    Editar

  2. Opening the iPod can be challenging. Don't get discouraged if it takes a few tries before the iPod is opened.

    • Opening the iPod can be challenging. Don't get discouraged if it takes a few tries before the iPod is opened.

    • Insert a plastic iPod opening tool in the seam between the white plastic front and metal back of the iPod. Once you've inserted the tool, run it along the seam to free the five tabs holding the iPod together.

    Editar

  3. Continue to run the opening tool along the side of the case until all five tabs have been released.

    • Continue to run the opening tool along the side of the case until all five tabs have been released.

    Editar

  4. Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.

    • Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.

    Editar

  5. Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now

    Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now

  6. Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.

    • Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.

    Editar

  7. Lift the rear panel away from the iPod, making sure it doesn't catch on the headphone jack.

    • Lift the rear panel away from the iPod, making sure it doesn't catch on the headphone jack.

    Editar

  8. Peel up the metallic tape attached to the top of the battery.

    • Peel up the metallic tape attached to the top of the battery.

    Editar

  9. Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).

    • Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).

    Editar

  10. Lift up the end of the hard drive near the Firewire port to allow easy access to the battery connector.

    • Lift up the end of the hard drive near the Firewire port to allow easy access to the battery connector.

    Editar

  11. Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

    • Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

12 personas más completaron esta guía.

Autor

con 1 otro colaborador

iRobot

Miembro Desde 24/09/09

1 Reputación

623 Guías creadas

Insignias: 35

+ 32 más insignias

Un Comentario

Agregar un comentario

Nice easy fix. Modern batteries are twice the capacity too. These old gen iPods are great. Nice to have an apple product not made in China.

peter barker - Contestar

Agregar Comentario

1024

Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 10

Últimos 30 Días: 69

Todo El Tiempo: 21,074