Saltar al contenido principal

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Zoom Q3HD Handy Video Recorder Lense Cleaning

Qué necesitas

  1. Zoom Q3HD Handy Video Recorder Lense Cleaning, Lens: paso 1, imagen 1 de 1
    • Remove the two screws from the bottom of the device.

    • Make sure to put your screws in a safe place.

  2. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 2, imagen 1 de 1
    • Flip the device over and remove the four screws bordering the grate of the device.

  3. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 3, imagen 1 de 1
    • On the front of the device, slide the battery compartment cover off by pushing inward and sliding downward.

  4. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 4, imagen 1 de 1
    • Remove the two screws from the lip of the battery compartment.

  5. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 5, imagen 1 de 1
    • Remove the final screw from the bed of the battery compartment.

  6. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 6, imagen 1 de 1
    • WARNING: Pieces may become loose when you separate the device in half!

    • Run the pry tool along the edges of the device to begin separating the device in two halves.

  7. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 7, imagen 1 de 2 Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 7, imagen 2 de 2
    • REMINDER: Pieces may become loose when you separate the device in half!

    • Apply upward pressure to fully separate the device into two halves.

  8. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 8, imagen 1 de 1
    • WARNING: If you’re not careful with keeping the screen close to the board, you will rip off the ribbon attaching the screen to the circuit board.

    • Lift display screen keeping the top half close to the board.

  9. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 9, imagen 1 de 1
    • Gently flip the black clip up attaching the ribbon of the screen to the circuit board.

  10. Zoom Q3HD Handy Video Recorder Lense Cleaning: paso 10, imagen 1 de 1
    • Gently slide the ribbon from the circuit board, removing the screen.

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Grace Bently

Miembro Desde 10/13/14

4 Reputación

1 Guía escrita

Equipo

Ohio State, Team 1-1, Mccook Fall 2014 Miembro de Ohio State, Team 1-1, Mccook Fall 2014

OSU-MCCOOK-F14S1G1

4 Miembros

1 Guía escrita

3 comentarios

My zoom q3HD only have the red light turned on when powering up. No display at all. What is happening? How can I claim warranty? I didn't use the device more than a year. Help me

stancalvin - Contestar

This is not comlete, leaves you half way through, would be great if you could finish this, thank you.

smoldas.l - Contestar

Yes it would be good to see it finished. I am half way through taking mine apart to clean the lens amd i don't know if i should proceed or not. Its the 2nd time the lens has fogged up. My 2nd q3hd.

steven kemsley - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 6

Ultimos 30 días: 15

Todo El Tiempo: 1,956