Repara tus cosas Comunidad Tienda

Shure SM58 XLR Connector Wire Repair

Introducción

The XLR Connector is the part of the microphone that plugs into the cable which carries the sound to the sound mixer and speakers.

Qué necesitas

  1. Shure SM58 XLR Connector Wire Repair, XLR Microphone Connector Disassembly: paso 1, imagen 1 de 1

    • Using a small flat head screwdriver, gently turn the retaining screw at the bottom of the microphone counterclockwise until it stops or provides resistance.

    • The retaining screw is mounted to the connector and has a left-handed thread. Turning the screw clockwise locks the connector in place. Turning it counterclockwise lowers it down into the hole, releasing the connector.

    • Once the screw stops, do not try to loosen it further.

    Editar

    Its an old microphone, I'm not the first owner. The screw keeps going infinite and not enough to the connector to come off. What can I do?

    nunoandrade - Contestar

  2. Shure SM58 XLR Connector Wire Repair: paso 2, imagen 1 de 1

    • Plug an XLR cable into the loose connector.

    • While holding the disconnect button down, pull on the cable to remove the connector from the body of the microphone.

    Editar

  3. Shure SM58 XLR Connector Wire Repair, Shure SM58 XLR Connector Wire Repair: paso 3, imagen 1 de 1

    • If the wire is not exposed from the insulation, strip the broken wire.

    Editar

  5. Shure SM58 XLR Connector Wire Repair: paso 4, imagen 1 de 1

    • Bend the wire around the contact point. Pin numbers are located on the outside of the connector.

    • Connect the red wire to Pin 3 and the blue wire to Pin 2.

    • Pin 1 should have a single piece of exposed wire connecting it to the metal plate on the top of the connector (the ground plate).

    Editar

  6. Shure SM58 XLR Connector Wire Repair: paso 5, imagen 1 de 1

    • Clamps are helpful for this step.

    • In one hand, hold the solder. In the other, hold your soldering iron.

    • Touch both the soldering iron and the solder to the contact point. The solder should melt and create a connection between the wire and the microphone connector.

    Editar

  7. Shure SM58 XLR Connector Wire Repair: paso 6, imagen 1 de 1

    • Remove the solder and then the soldering iron from the contact point.

    • If you remove the soldering iron first, the solder may become stuck to the contact point.

    • Let the wire cool for 30 seconds or so.

    • If the wire is not completely connected repeat steps 2 through 5.

    Editar

  8. Shure SM58 XLR Connector Wire Repair: paso 7, imagen 1 de 1
    Editar
Conclusión

After soldering the wires to the XLR connector and reassembling your microphone, your microphone should be ready to plug in to the XLR cable and function properly.

4 personas más completaron esta guía.

Autor

con 9 otros colaboradores

nat coll

Miembro Desde 09/27/12

721 Reputación

14 Guías creadas

Insignias: 12

+ 9 más insignias

Equipo

Cal Poly, Team 7-53, Forte Fall 2012 Miembro de Cal Poly, Team 7-53, Forte Fall 2012

CPSU-FORTE-F12S7G53

Miembros de 5

30 Guías creadas

9 comentarios

Many thanks. Very helpful.

Namron - Contestar

Yes I'm glad it was so simple and quick to fix my mic!

heyaly - Contestar

Red wire to pin 3? Seems to go against the pin 2 hot method?

Jim - Contestar

I'm not familiar with the "pin 2 hot method." We took a working mic apart and reassembled it the way we found it, so I'm pretty that is the correct soldering configuration.

Daniel Berger -

Świetna strona. Brawo.

Kazimierz Serafin - Contestar

Son riuscito a capire meglio i colori che sul sito della Shure

emeritomm - Contestar

Works like a charm. Thanks for the tip about the left-handed treading. My SM58 is like 100 years old and that screw worked itself loose..when I pulled the XLR out the plug came with it and broke the wires off.

To avoid this issue I will periodically check-tighten all set screws in my mics, and now I know why you are supposed to be careful when unhooking - I took for granted how tough these mics are and like 30 years later it broke.

Fully operational and a great father/daughter project afternoon thanks to this tutorial!!

Watch out those microphone pins get hot on the other end - DON’T TOUCH.

Christopher Schooley - Contestar

Great information! Do you know where I can get the connector with the xlr pins that goes in the bottom of the mic? I have one that is missing the bottom connector. It’s an SM58 and Shure wants like $65 to sent it in and get it swapped out but it just needs that one part, lol

Jenny Starr - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 3

Ultimos 7 días: 16

Ultimos 30 días: 98

Todo El Tiempo: 30,191