Saltar al contenido principal

Qué necesitas

  1. Roku 4 Motherboard Replacement, Motherboard: paso 1, imagen 1 de 1
    • Place the Roku 4 face-down on a table. The rubber sticker should be facing you.

  2. Roku 4 Motherboard Replacement: paso 2, imagen 1 de 1
    • Starting at one corner of the device, pull the rubber sticker back toward the opposite corner of the device carefully to reveal the underlying screws.

    • Completely remove the rubber sticker to reveal the underlying screws on the device.

    • Place the rubber sticker facing up on the table to preserve its adhesiveness. It will be needed to reassemble the device.

  3. Roku 4 Motherboard Replacement: paso 3, imagen 1 de 1
    • Turn the Phillips PH1 screwdriver counterclockwise to unscrew all 4 of the 12.0 mm screws.

    • Store the screws in a safe place, such as on a magnetic project mat, so they do not get lost before reassembly.

  4. Roku 4 Motherboard Replacement: paso 4, imagen 1 de 2 Roku 4 Motherboard Replacement: paso 4, imagen 2 de 2
    • Turn the device over so you can see the "4" on the top cover.

  5. Roku 4 Motherboard Replacement: paso 5, imagen 1 de 2 Roku 4 Motherboard Replacement: paso 5, imagen 2 de 2
    • Wedge a plastic opening tool into the seam between the top cover and bottom casing of the device and create a gap.

    • Prying open the device is quite difficult and requires a large amount of force. Use caution to avoid breaking the device or hurting yourself.

  6. Roku 4 Motherboard Replacement: paso 6, imagen 1 de 1
    • After you have created a gap large enough to fit your fingers between, gently lift up the top cover to open the device and reveal the motherboard.

    • The motherboard should still be attached to the underside of the top cover by a red wire, a blue wire, and a black wire.

  7. Roku 4 Motherboard Replacement: paso 7, imagen 1 de 3 Roku 4 Motherboard Replacement: paso 7, imagen 2 de 3 Roku 4 Motherboard Replacement: paso 7, imagen 3 de 3
    • To begin removing the motherboard from the plastic casing, pinch the black plastic clip and gently pull upward.

    • Once you feel the motherboard begin to loosen from the plastic casing, pull it upward to remove it completely.

    • The motherboard should still be attached to the underside of the top cover by a red wire, a blue wire, and a black wire.

  8. Roku 4 Motherboard Replacement: paso 8, imagen 1 de 3 Roku 4 Motherboard Replacement: paso 8, imagen 2 de 3 Roku 4 Motherboard Replacement: paso 8, imagen 3 de 3
    • Peel back the black adhesive strip that attaches the blue wire to the motherboard.

    • Repeat this step for the strip that attaches the black and red wires to the motherboard.

  9. Roku 4 Motherboard Replacement: paso 9, imagen 1 de 3 Roku 4 Motherboard Replacement: paso 9, imagen 2 de 3 Roku 4 Motherboard Replacement: paso 9, imagen 3 de 3
    • Using a soldering iron, desolder the blue, red, and black wires from the motherboard.

    • Consult iFixit's Soldering Skills guide to safely use the soldering iron.

    • The motherboard should now be completely disconnected from the top cover of the device.

Conclusión

Follow these steps in the reverse order to reassemble your device.

7 personas más completaron esta guía.

Bradley Rains

Miembro Desde 26/03/17

151 Reputación

1 Guía escrita

Equipo

Baylor, Team S5-G4, Williams Spring 2017 Miembro de Baylor, Team S5-G4, Williams Spring 2017

BU-WILLIAMS-S17S5G4

3 Miembros

4 Guías creadas

3 comentarios

Thank you, have you upgraded to a new 2019 Ultra model yet?

Allan Landwer - Contestar

Soldering the fan to the mobo is a suck move. However, they used a good quality bearing-less fan.

smbrannon - Contestar

Can you gve me areson? will it suck out the perfomance?

Kind-hearted, spirited Man -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 11

Ultimos 30 días: 42

Todo El Tiempo: 4,959