Whether you're stacking firewood for the winter or heading into town for coffee, don’t let a blown-out button keep you from wearing your favorite pair of pants. With the help of this guide and a hammer you can have your pants or jeans ready for action in minutes.

For replacement parts or further assistance, contact Patagonia Customer Service.



  1. Lay your jeans front-side up on a sturdy table or workbench.
    • Lay your jeans front-side up on a sturdy table or workbench.

    • Unzip the fly and open the jeans at the waistband to reveal the hole where the button is missing.

    • Hold the waistband at the hole and turn it over, so you can see the back of the hole.

    • Be sure to fully remove the old button before installing a new button.

    Agregar Comentario

  2. Insert the tack into the back of the hole.
    • Insert the tack into the back of the hole.

    • Push the tack through the hole.

    • If the hole is too large, you can make a new, smaller hole for the tack in an undamaged section of the denim as close the existing hole as possible. Then push the tack through the new hole.

    Agregar Comentario

  3. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • Holding the tack in place from behind, place the button on top of the tack.

    Agregar Comentario

    • Place a flat work surface like a scrap piece of wood or a cutting board directly beneath the tack and between the front and back of the jeans.

    • Be sure to use a small (one pound) hammer or mallet to prevent breaking the button.

    • Hammer the button onto the tack, with a straight downward pound.

    • If you’re uncomfortable holding the button with your fingers while you hammer, you can use a pair of pliers to hold the button in place.

    Thought it would be better if I flipped the jeans over and hit the tack instead of the button. But I wrecked it. Don’t do that.

    Sharon Barke - Contestar

    • Test out your new button by buttoning the jeans to ensure the new button is set and secure.

    Agregar Comentario

Linea de Meta

23 personas más completaron esta guía.

Brittany McCrigler

Miembro Desde 05/03/12

80,075 Reputación

132 Guías creadas


iFixit Miembro de iFixit


113 Miembros

7,342 Guías creadas

Nice, but let's consider how this situation occurs. The tack comes out of its hole, just simply replacing it is not realistic, unless the new tack is significantly bigger. So how do you "repair" the hole such that it will hold a tack again?

Gabe Misura - Contestar

As noted in step 2, you can move the tack over to where the denim isn't damaged. If that will cause the jeans not to fit properly, you can sew a folded piece of denim behind the hole (sew around the edges on the inside of the jeans) and punch the tack through the new piece.

Brittany McCrigler -

I didn´t have a new button and was in a pinch. Just ripped the old button off completely, jammed it in the tail end of a hammer and yanked it apart with som pliers. Then i followed the instructions in this fix. Worked like a charm, so far...

fredrikbendiksen - Contestar

The best thing to do is patch the hole. I simply use fabric glue and some pieces of blue jeans that you probably have hanging around. Trim off the extra threads and then apply fabric glue to the back of the waist band covering the hole made by the old button. Do the same on the front and then let dry. about 30 minutes or so, if you have a machine I always stitch back and for on the edges. Trim any edges or use additional glue to tack them down. Now because you have strengthened the hole carefully push the back of the button through where you can see the end, add the front to the nail end and turning the garment face down on a protected hard surface hammer about 3 times and check to see if it is sturdy, continue to hammer until you have reached the objective. Now you have got many more years with that button.

melanie1150 - Contestar

Can I reuse the old button and tack by hammering them together after I’ve inserted them into the old hole?

Pat Mirza - Contestar

I wanted to back the button back to the short not make a new button!

King Zero - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 113

Últimos 7 Días: 900

Últimos 30 Días: 4,189

Todo El Tiempo: 122,068