Saltar al contenido principal

Introducción

Requerimientos previos para cambiar el Botón de Inicio en tu iPhone 5s.

Por favor, ten en cuenta que solamente el sistema del botón inicio "original" tiene la capacidad de usar la funcionalidad el Touch ID. Instalando un nuevo botón de inicio ordinario, solamente restaura las funciones de un botón simple (similar al del iPhone 5, 4, 4s, etc), no la capacidades del Touch ID.

  1. Desenrosca el tornillo de sujeción Phillips #000 que asegura el cable del botón de inicio. El tornillo de sujeción se sujeta al cable botón de inicio por un soporte elástico de contacto. Durante el reensamblaje, asegúrate de que el contacto esté en la orientación correcta, en el lado del tornillo más cercano a la pantalla LCD.
    • Desenrosca el tornillo de sujeción Phillips #000 que asegura el cable del botón de inicio.

    • El tornillo de sujeción se sujeta al cable botón de inicio por un soporte elástico de contacto. Durante el reensamblaje, asegúrate de que el contacto esté en la orientación correcta, en el lado del tornillo más cercano a la pantalla LCD.

    • Si tu pieza de repuesto no tiene este tornillo de sujeción y el contacto de soporte elástico, necesitarás transferirlos al nuevo cable.

    The tiny "captive spring" came off of the back of the screw and I struggled to get it to go back on. I ended up placing the spring over the hole where the screw goes in, with the holes lined up then putting the screw through both.

    Also, the replacement screen I received from ifixit.com was slightly different than the original. The small metal tab where this screw goes in was not slightly bent downward like the original. It didnt make any difference. The screw went back in as normal.

    Nathan - Contestar

    Hi,

    The home button doesn't work ?

    Help

    Sultan - Contestar

    BE CAREFUL HERE.

    This so called 'captive' screw is not very captive at all and I have nearly lost it twice now.

    If it does fall out, look closely at the pictures to figure out the orientation of the grounding finger.

    Ben - Contestar

    Two things - As mentioned, the replacement screen is a bit different. Mine had a screw where an empty hole should have been for the "captive screw".. a bit confusing at first. Just remove it and carry on.

    Second, if you're an occasional nunce like me, you might be confused by the little tab/prong/raised guy next to the screw. After you've screwed the "captive screw" in, that thing should be hovering above it/the metal plate of the screen, and should look just like the removal picture.

    easleyjs - Contestar

    Out of curiosity, what happens if the "spring contact backing" is not in the correct orientation?

    I re-assembled my phone without paying any attention to this, and it seems to work OK... maybe I coincidentally got it right without trying. What would happen if the contact was facing the wrong way?

    wilsonmichaelpatrick - Contestar

    Hi Help !!! The home buton doesn't work anymore !

    Chris91177 - Contestar

    what if you lose the spring contact. does the phone work without it? if not, where can I find a spring contact?

    Andreas Kouroupis - Contestar

    I have this same problem. I lost mine but found the screw where can I order one from?

    kristlewomack -

    I also have this problem, do any home buttons come with this piece?

    viarengo1 -

    Hello. I lost the little 'spring clip'. My phone is working erratically. Could that be anything to do with the cip not being in place? Thanks

    ggough60 - Contestar

    I am pretty sure I had replaced the captive spring wrong (didn't see the second image until I have completed the project). But the phone seems to have a perfectly working home button now.

    Alan Kang - Contestar

    This screw/spring combo fell off right before reassembling. Good luck and found the screw again. So my advice: Put a tape around the screw/spring or dismount them from the cable and put them in a safe place. The spare screw delivered with the display was too short.

    Tom Vee - Contestar

    I thought I lost the spring contact, but it actually just got rotated under the section of cable that the captive screw is attached to. The spring contact should be "captive" at the same place the screw is so it should'nt get lost too easily.

    Anand Varma - Contestar

    On the phone I worked on, the screw wouldn’t separate from the “captive spring.” LEAVE IT! It’s more trouble than it’s worth to remove it, Just reuse the screw it will make the re-install on the new screw much easier. Also use the tweezers to hold the spring in the correct orientation as you screw it back on.

    Benjamin Finley - Contestar

    During reassembly, I wasn’t sure wether the spring contact backing was beneath or above the cable. It is hard to see in the 2nd image in step 23.

    But in step 24 the 2nd image shows that the spring contact backing is right under the cable.

    So the spring contact backing goes first, then the cable and then of course the screw.

    Wolfgang Bauer - Contestar

    For the life of me, I cannot get this screw out. I have been using the same screw driver and nothing has been working.

    Warren Binder - Contestar

    I think there is one step missing here which shows a picture with the correct position of the ‘spring contact backing’. Consider the part which has a hole in the middle: the flat part is sided to top, making the round part sided to bottom. This is a clear picture of the ‘spring contact backing’: http://www.icellulartech.com/iphone-5s-h... (if the link is broken by the time you see it, type the name in Google).

    Andre Silva - Contestar

    I had a problem when reassembling, I removed this little screw and the spring contact from my original screen to put them in the new one, but the new one had already its own screw, soI just removed it and tried to put the screw from my original screen into the new one but it didn’t work, and the worst thing of all is that I lost the screw that came with the new screen and that’s the only one that works.

    Elías Eduardo Reyes Vázquez - Contestar

    May seem silly to say this…. however it might prevent some confusion for others.

    my replacement screen had a screw that needed to be removed in order for the captive screw and home button cable to be secured.

    Dean Allan Land - Contestar

    When I unscrewed it, the spring contact part moved too & the little prong rotated under the cable. I thought (mistakenly) that this was its intended position. The screw also came loose, which made reassembly difficult until I saw that 2nd photo above and realized what the orientation was supposed to be.

    The order is screw -> cable hole -> spring contact -> screw hole.

    The rounded edge of the spring contact should face the bottom of the phone to match up with the hole’s rounded edge. The perpendicular ‘lip’ should sit flush against the metal plate. The prong should stick up toward where the screen will be. Really, there’s only 1 possible way to put it on correctly, but without seeing the correct orientation first, or if the screw detaches from the cable, it’s kind of a pain to get them back together.

    seijihuzz01 - Contestar

  2. Dobla el cable del botón de inicio hacia abajo, fuera del camino del soporte del botón de inicio. Dobla el cable del botón de inicio hacia abajo, fuera del camino del soporte del botón de inicio.
    • Dobla el cable del botón de inicio hacia abajo, fuera del camino del soporte del botón de inicio.

    Aiuto, ho sostituito il touch screen e non mi funziona più il riconoscimento dell’impronta digitale (touch id). Chi può aiutarmi. Grazie

    Orazio Coccia - Contestar

  3. Retira los dos tornillos Phillips # 000 de 1,4 mm del soporte del botón de inicio.
    • Retira los dos tornillos Phillips # 000 de 1,4 mm del soporte del botón de inicio.

    Screws are stuck...! no way that I can unscrew them :-(

    Sumit Bhatnagar - Contestar

    I had this issue, screws were so tight my screwdriver was starting to strip them. I managed to get one side off by applying massive pressure. I then wiggled the plate around to loosen the other side.

    mrnoxious -

    Hi every body! I would know much pressure the iphone 5s 's lcd can resist approximately !!? Have you ever stand on it?this happend for me , and in some positions under the direct sun light when the screen is ON , it seems that there is some pits on lcd ! ;-( please help ! If you had the same case! Help Thank You***

    Bryan - Contestar

    I could not get a phillips #000 to release these, but a phillips #00 did the trick perfectly. South African version of the phone, if that makes a difference.

    Andrew - Contestar

    these are the tightest screws I've ever seen in my life. Tried applying massive pressure and just stripped the screws. Not sure what to do now

    Bob Mcroy - Contestar

    Use the #00 Philips on these screws

    leeprobert - Contestar

    Went and bought a #00 when the #000 didnt work. Still no luck. About to lose my mind with frustration.

    Mike Manning - Contestar

    I could not get the 000 or the 00 to work, therefore I tried a #1 flat head from the kit and it worked like a charm.

    Sean O'Donohoe - Contestar

    Sometimes just switching to another screwdriver might help. I noticed that the screwdrivers you often get with displays assemblies are just crap. Invest in a good one.

    Didier Daniel - Contestar

    I was successful by using a 1.5 Phillips screwdriver head from a Stronger toolkit TK-LA40-38PCS

    Elaine Palmer - Contestar

    Glad I’m not the only one I guess. Using insane pressure for such small parts I was able to get the one not originally covered by the cable out. Then the trick of wiggling the bracket loosened the other one which was somewhat stripped by my earlier attempts with 00 and 000 Phillips. What a scare

    Bill Pennock - Contestar

    I had success using the J000 screw from the iFixit Pro kit

    Kalin Fetvadjiev - Contestar

    Both of the screws have blue loc-tite on them. Best to make sure you have the right screw driver for the job. Also, if you have the “iopener”, you can apply a little “heat”. That will loosen up the loc-tite.

    Dean Allan Land - Contestar

    these screws are impossible to get out…

    Cameron Bell - Contestar

  4. Kits de Reparación de Batería de MacBook Air

    A partir de $69.99

    Buy Now

    Kits de Reparación de Batería de MacBook Air

    A partir de $69.99

    Buy Now
  5. Retira el soporte del botón de inicio del ensamblaje de la pantalla.
    • Retira el soporte del botón de inicio del ensamblaje de la pantalla.

    For those having problems transferring their home button to the new display assembly: When installing the home button into the new display assembly I had the problem that the bracket kept the button "pressed down" because the button did not sink into the front panel completely. After removing the home button and reassuring that there was no dust or similar particles preventing the home button from sitting correctly, I still had to push gently to get the home button into the correct position.

    larscmueller - Contestar

  6. Inserta la punta de un spudger debajo del conjunto que conforma el botón de inicio. El cable del botón de inicio está fijado con un adhesivo suave.
    • Inserta la punta de un spudger debajo del conjunto que conforma el botón de inicio.

    • El cable del botón de inicio está fijado con un adhesivo suave.

    • Suavemente, trabaja el spudger debajo del cable para separar el cable del botón de inicio del conjunto del panel frontal.

    • No retires el botón de inicio, ya que todavía está conectado al conjunto del panel frontal.

    It can be easier to come in from the other way than shown in the image, near the home button.

    Calion - Contestar

    I think this is easier to do with the blue ifixit opening tool (this guy: iFixit Opening Tool) than the spludger. It gets underneath the cable more easily.

    Jonathan Stucklen - Contestar

  7. Si es necesario, retira la cinta sobre el botón de inicio en la parte frontal del ensamblaje del panel frontal agrietado. Empuja suavemente la esquina superior izquierda del botón de inicio hacia arriba lejos del panel frontal.
    • Si es necesario, retira la cinta sobre el botón de inicio en la parte frontal del ensamblaje del panel frontal agrietado.

    • Empuja suavemente la esquina superior izquierda del botón de inicio hacia arriba lejos del panel frontal.

    • No presiones el botón de inicio totalmente, sólo tiene que obtener una esquina libre, por lo que se puede levantar con un spudger.

    • Esta membrana es muy delgada. Si sientes que vas a romper el botón, aplica calor y vuelve a intentarlo.

  8. Retira el botón de inicio el resto del sistema fuera de la pantalla, haciendo palanca suavemente con un spudger. Retira el botón de inicio el resto del sistema fuera de la pantalla, haciendo palanca suavemente con un spudger.
    • Retira el botón de inicio el resto del sistema fuera de la pantalla, haciendo palanca suavemente con un spudger.

    DO NOT skip this step, or you will damage the very gentle rubber hold around the home button, and that may result in a broken home button.

    Addison Rasmussen - Contestar

  9. Retira el conjunto del botón de inicio del panel frontal.
    • Retira el conjunto del botón de inicio del panel frontal.

    Take a moment to clean any crud from the perimeter of the home button itself BEFORE reinstalling…

    finnik2d - Contestar

    Take a moment to clean off any crud from around the perimeter ring of the home button. Use a sewing needle for its sharpness to CAREFULLY pick away any debris. Makes a clean assembly for when re-assembling the button back into a new display module.

    finnik2d - Contestar

Conclusión

Para armar nuevamente tu dispositivo, sigue estas instrucciones en orden inverso.

34 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Sam Lionheart

Miembro Desde 18/10/12

367,379 Reputación

537 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

104 Miembros

8,413 Guías creadas

Unfortunately this will never work, the sensor is paired to the logic board. If you want to replace the defective tactile switch, remove all the plastic/rubber parts on the flex cable and resolder a new switch or disassemble the switch and clean/replace the metal dome switch. If you want to repair fingerprint function, just give up.

Tom Chai - Contestar

I purchased a full iphone 5S home button replacement assembly (comes with the home button attached to the flex cable) And now the fingerprint function does not show up at all. Where it's supposed to show in settings as "Touch ID and Passcode" It only says passcode. Restored as new to 7.1, still doing the same thing.. Anybody have ideas?

Casey - Contestar

Only the home button that came with the phone has Touch ID function. In order to replace it and still have Touch ID, you would need to get it replaced at an Apple Store.

p3rs0nn -

I think you can easily break the Touch ID sensor

nguyenquanganh38 - Contestar

Hey I changed my screen but now the home button doesnt work properly, it does work but it doesnt make the usual clicking sound and only works with a firm press, although the fingerprint does still work so not sure what the issue is.. any ideas?

Luke Earp - Contestar

I bought the home button assembly replacement (the part without the button), but there are no steps regarding the separation of the button plate from the old flex assembly. Can you please give some advice?

Thank you.

Lorenzo - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 25

Todo El Tiempo: 23,058