Introducción
Por precaución, quita todos los accesorios conectados a la cámara antes de retirar los lentes.
Qué necesitas
-
-
Quita las baterías abriendo la cobertura en la parte inferior de la carcasa.
-
-
-
Remueve los siguientes 6 tornillos Phillips que permitirán el acceso al interior de la cámara.
-
Remueve los dos tornillos en el lado derecho de la cámara, cerca al puerto HDMI.
-
Remueve los dos tornillos en el lado opuesto de la cámara.
-
Remueve los dos últimos tornillos en el lado inferior de la cámara, cerca al agujero del trípode.
-
-
-
Utilizando un spudger de plástico, lentamente empuja hacia afuera el cable plano haciendo uso del agujero mostrado en la imagen. El primero de los tres conectores lógicos que conectan la pantalla a la cámara ahora está retirado.
-
La pantalla ahora debe estar parcialmente desconectada de la parte posterior de la cámara.
-
-
-
-
Con el fin de retirar los otros dos conectores, el frente de la carcasa debe quitarse. Lentamente, haz palanca alrededor de los bordes utilizando una herramienta plástica de apertura para liberar la carcasa. Una pieza del anillo de los lentes se caerá desde el interior de la cámara; ponla a un lado.
-
-
-
Para quitar el conjunto del flash, desconecta la conexión flex y mueve la unidad de flash fuera.
-
-
-
Utilizando una herramienta para hacer palanca, retira el soporte de los lentes.
This is separating the lens from the sensor so be careful with both. You can disassemble the lens itself but is a Real Puzzle to reassemble. With five rings that have to mesh correctly, not to mention the position of the aperture and the Image Stabilized middle lens, and two flexes that have to be put in their correct locations.
-
Para ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Para ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
10 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Fuzzy_Pickles nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
Equipo
UW Tacoma, Team 1-2, Liner SU 2015 Miembro de UW Tacoma, Team 1-2, Liner SU 2015
UWT-LINER-SU15S1G2
4 Miembros
5 Guías creadas
9 comentarios
There is a step missing, on removing the flash, one side screw and one front, above the lens, otherwise perfect. thank you so much, just as above I had a lens error and ordered a replacement for 14£ from ebay. all works now. thanks.
Is there no other 'fix' without replacing the lens assembly on this particular "Lens error "issue?
@profeduards: try to reseat the flexes from the aperture and IS. You can disassemble the lens to reset the position and/or remove sand but make lots of pictures of the process, and mark (with pencil) a line over the rings (from the front) to know what ring goes where when reassembling. It's possible to reassemble without (as I did, lens was extended so i couldnt) but the process is long, arduous and takes a lot of patience.
Thanks, my Lens was bricked, and with a new Lens kit @15$ from china, it was fixed.
Bought a new lens from ebay, replaced it and it worked for two days. But now, when I hit the ON-button, lens go out, the titlescreen pops up but then all is black. And when I try to turn it off, the lens won´t go back in. There is no message of lens error. I can push the playbutton to get the lens to go back in. And I can also see old pictures so nothing wrong with the LCD. Could the new lens be damaged? Also tried to reset the flexcables several times but the problem remains. Any ideas out there?
Holger, look at Step 7. The 2nd flex cable from the left at the top of the camera—be sure that cable is seated well. I just had my camera apart and the screen was not lighting so I reset a couple of cables and that was the one that brought the screen back. I did a complete tear down following these instructions and put it back together. The lens came out and the lens message came back on. I’m wondering if this might have something to do with the motor. I was thinking that the wheel/gear that is attached to the motor drive should be secured on the spindle. Mine was not. It did manage to drive the lens out once. I’m not sure what kind of motor that is and how it works but I’m thinking the next time I take it apart I might just epoxy that gear onto the end of the spindle (unless someone here tells me not to because it is supposed to be that way). Thanks.
