Introducción
Usa esta guía para reemplazar la placa madre en tu dispositivo.
Qué necesitas
-
-
Usa tu dedo o la punta de un spudger para para comprimir el pasador que asegura la correa del reloj.
-
Con el pasador comprimido, retira la correa del reloj.
-
-
-
Inserte una herramienta de apertura en la pequeña muesca junto al agujero del micrófono.
-
Desliza la herramienta de apertura alrededor del perímetro del anillo de ajuste mientras se alza ligeramente para cortar el adhesivo que asegura el anillo al reloj.
-
Remueve el anillo de ajuste.
-
-
-
Usa una herramienta de apertura para empujar lentamente el anillo de ajuste del botón hacia arriba.
-
Remueve el anillo de ajuste.
-
-
-
Use una pequeña llave de pernos para desenroscar el botón.
-
Remueve el botón
Leave the ring from the previous step partially in and use it as a wrench on the actual nut.
It's a great idea in theory, but how do you grip the ring to turn it?
You are my hero! Heating and trying to turn it using tweezers didn't work, but this did.
Brilliant suggestion many thanks.
How do you get the ring to do that? Having a hard time with this step 😅
Note that the recommended Spanner Set on this page is too big for this job, None of the "pins" fit.
Ik heb werkelijk geen idee hoe ik die pijn los krijg. Kan dit vergroot worden getoond op de foto? Eventueel met meer uitleg (welke kant draai je op, wat draai je precies). Verder super blij met deze uitleg, maar ik loop dus helaas vast.
-
-
-
Mientras mantienes la caja exterior firme, gira el ensamblaje interior del reloj en el sentido de las agujas del reloj hasta que se detenga.
-
-
-
-
Usa una uña o herramienta de apertura para levantar el ensamblaje inferior de plástico del ensamblaje de la pantalla.
-
-
-
Utiliza unas pinzas para retirar la pequeña tira de goma que hay entre la batería y el conector ZIF de la pantalla.
What if the rubber strip tears? What is it’s purpose?
This and the following step are unnecessary.
Adding another comment not to do this step or the subsequent ones for removing the display connector. They are unnecessary, and the parts are fragile. Otherwise an excellent guide.
-
-
-
Use un spudger para levantar la tapa de cierre del conector ZIF de la pantalla.
I cannot reattach my display cable and my watch is now useless. Really angry as this step IS NOT NECESSARY. You can easily change the battery without doing this. DON’T DO THIS.
Agreed - this should be removed from instructions. It is just destructive. Wish I had seen these comments before I did this.
Agree with all the above. AND I am replacing the display so I MUST attach the new cable and cannot for the life of me figure out this ZIFF connector. It is a mystery.
-
-
-
Usa el extremo plano de un spudger para sacar suavemente la batería de la caja.
It mentions that the glue is to be replaced, but it does not explain what glue to use and how to use it.
Elmer’s rubber cement worked for me. I put some on the bottom of the battery and on the ring that had the glue softened in the first steps. It has held well so far, maybe 3 weeks or so.
At this point, I would connect the new battery and re-assemble the watch (without the crown and ring) and test the battery and watch by trying to charge it. This way, if it doesn’t charge, you don’t have to do a full disassembly to figure things out. Once the watch is charged to 100%, you can re-assemble. Also, it took about a minute before the new battery looked like it was charging (while on the charger) so give it some time.
Something not mentioned here is that the gold crown trim piece has 3 long and 3 short prongs. You need to align these to the matching sized holes in order for it to go in correctly. If you don’t, the trim piece will not go in properly. Before concluding your work, ensure that pressing the crown results in going to the menus (to verify it’s screwed in enough and functional).
-
-
-
Remueve la batería.
Completed, but have a spot on the screen now. I have a feeling that taking this watch apart has killed all the water resistance and I’ll be in the market for a new watch very soon. Everything about this repair feels like a moonshot. Frustrating. it’s just a battery. they should be easily replaceable. Full stop.
Agree with the first comment. Also, does the copper foil that is on the old battery need to be installed on the new battery?
-
-
-
Desprende la cinta de cobre que conecta la placa madre y la pantalla.
-
Usa el spudger para separar la carcasa de la placa madre de la carcasa trasera.
Do not follow this it makes you break the piece that holds the button in. I broke my watch following this. I figure it out afterward but too late, the button and its surrounding unscrews out.
I screwed up my touch screen on this step. Not sure how the ribbon for the battery is removed.
-
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
Una persona más ha completado esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Mariana Roca nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
Equipo
USF Tampa, Team S6-G1, Remmell Fall 2017 Miembro de USF Tampa, Team S6-G1, Remmell Fall 2017
USFT-REMMELL-F17S6G1
4 Miembros
19 Guías creadas
