Introducción
Usa esta guía para quitar o reemplazar la pantalla de tu Motorola Moto Z3 Play.
Antes de comenzar, descarga la aplicación Rescue and Smart Assistant para hacer una copia de seguridad de tu dispositivo y diagnosticar si tu problema está relacionado con el software o el hardware.
Advertencia: Debido al fuerte adhesivo que asegura la pantalla, al mínimo espacio para insertar sus herramientas y al alto calor necesario, existe una buena posibilidad de dañar accidentalmente la pantalla al retirarla. Si vas a sustituir la pantalla de todas formas, no tienes que preocuparte, pero si tienes intención de volver a utilizarla, ten mucho cuidado al calentarla y al insertar las herramientas para separar la pantalla del resto del dispositivo.
Qué necesitas
-
-
Apaga tu teléfono antes de completar cualquier paso de reemplazo.
-
-
-
Calienta los bordes de tu pantalla durante dos o tres minutos con una pistola de calor. Ajusta la pistola térmica a 85 grados centígrados, y ten cuidado de no mantenerla en una posición durante mucho tiempo; para evitar dañar la LCD. La pantalla debe estar muy caliente, pero no debe ser dolorosa al tacto. Vuelve a calentarla si es necesario.
-
-
-
-
Aplica un iOpener en el borde inferior del ensamblaje de la pantalla durante aproximadamente un minuto para aflojar el adhesivo que se encuentra debajo del sensor de huellas digitales.
-
-
-
Remueve el sensor de la huella digital con un par de pinzas.
Thanks for the great guide. I had to use my low watt heat gun, sparingly. Also lots of glue to remove and then re-apply. Really good pictures helped.
-
Compara tu parte de reemplazo nueva con la parte original. Podrías necesitar transferir cualquier componente o remueve los respaldos adhesivos de la parte nueva antes de instalarla.
Para volver a montar el dispositivo, sigue estas instrucciones en orden inverso.
Lleva tus desechos electrónicos a un centro de reciclaje certificado.
¿La reparación no salió como planificaste? Consulta nuestra comunidad de respuestas para ayuda en la resolución de problemas.
Compara tu parte de reemplazo nueva con la parte original. Podrías necesitar transferir cualquier componente o remueve los respaldos adhesivos de la parte nueva antes de instalarla.
Para volver a montar el dispositivo, sigue estas instrucciones en orden inverso.
Lleva tus desechos electrónicos a un centro de reciclaje certificado.
¿La reparación no salió como planificaste? Consulta nuestra comunidad de respuestas para ayuda en la resolución de problemas.
Cancelar: No complete esta guía.
27 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
9 comentarios
This is a guide for disassembly only. There are a few further steps required to replace front,,,
anyone else having a problem with the replacement screen not fitting? it seems like there is a bulge in the middle preventing the adhesive from keeping the screen attached to the frame on either side (top and bottom seals fine)
I have the same problem with mine……does anyone have a solution , that doesn't involve buying another screen
It is the battery ! Replace it before you assemble it. I made that mistake and it wasn't good. The battery swells with age as it wears out . It will keep the screen from being level and it will crack it .
Completed a screen replacement, but I have the same problem mentioned above. The left side of the screen doesn’t want to stay down and attached. I’m suspecting maybe the battery is slightly swollen. Only way to know for sure is to take it back apart and try to replace the battery as well (high risk).
Hi. I have a question. I have broken LCD on my MOTO Z2 play. Now I bought a new LCD and the LCD doesn´t work properly. Can be a problem with different model of LCD? The screen lights up but touching is not working? I noticed that there are different channels on the flex cable: Can be a different flex cable problem with working of touchscreen? Thanks for reply. David.