Razer Kraken Ultimate Motherboard Replacement

Introducción

The following the guide is how to remove the motherboard from a Razer Kraken Ultimate head set. All steps from previous guides must be taken before following these steps.

The motherboard breaking may cause the headphones to stop working entirely (see Troubleshooting) so it is important to know how to replace it.

Qué necesitas

Paso 1 Ear Pads

Razer Kraken Ultimate Motherboard Replacement, Ear Pads: paso 1, imagen 1 de 3

Razer Kraken Ultimate Motherboard Replacement, Ear Pads: paso 1, imagen 2 de 3

Razer Kraken Ultimate Motherboard Replacement, Ear Pads: paso 1, imagen 3 de 3

Grab the ear piece from one of the sides and lightly pull it outwards.
Ideally, do not pull the ear piece directly away from the speaker; it may damage the piece.

Editar

Paso 2

Once you have taken off one side, you can then remove the whole piece by slowly prying the pad away from the headphones.

Editar

Paso 3

Repeat steps on the other side.

Editar

Paso 4 Speaker

Razer Kraken Ultimate Motherboard Replacement, Speaker: paso 4, imagen 1 de 3

Razer Kraken Ultimate Motherboard Replacement, Speaker: paso 4, imagen 2 de 3

Razer Kraken Ultimate Motherboard Replacement, Speaker: paso 4, imagen 3 de 3

Remove the four 10 mm Phillips #00 screws securing the right speaker.
Be sure the device is unplugged before attempting to remove any of the screws.

Editar

Paso 5

Remove the 10 mm Phillips #00 screws securing the left speaker.
Note that one of the screws is hidden behind the product information sticker. Use your screw driver to punch a hole in the sticker.

Editar

Paso 6

To fully detach the speakers cut the wires as close as possible to the connection point, leaving plenty of room to solder the new speaker on.

Editar

Paso 7 Microphone

Razer Kraken Ultimate Motherboard Replacement, Microphone: paso 7, imagen 1 de 3

Razer Kraken Ultimate Motherboard Replacement, Microphone: paso 7, imagen 2 de 3

Razer Kraken Ultimate Motherboard Replacement, Microphone: paso 7, imagen 3 de 3

Remove the two 10 mm Phillips #00 screws securing the microphone.

Editar

Paso 8

Gently pry the bottom connection away from the casing with the iFixit opening tool.

Editar

Paso 9

Pull the microphone down and out of the casing.

Editar

Paso 10

Open up the casing the microphone retracks into.
Cut the cable as close to the microphone as possible, leaving behind enough to solder the new microphone to.
The casing the microphone if removed correctly in the previous step is easily opened by hand

Editar

Paso 11 Motherboard

Razer Kraken Ultimate Motherboard Replacement, Motherboard: paso 11, imagen 1 de 1

Remove the two 6 mm Phillips #00 screws that secure the motherboard.
One of the screws is located near where many cables connect; take care not to disconnect them.

Editar

Paso 12

Gently lift the motherboard from the case, with care not to damage any of the connected cables.

Editar

Paso 13

Razer Kraken Ultimate Motherboard Replacement: paso 13, imagen 3 de 3

There are two ribbon cables that must be removed.
To remove these cables pull the gray connecting piece out about 0.5mm to unlock the cable.
Then simply pull the cable out.

Editar

Paso 14

Repeat previous step with second cable.

Editar

Paso 15

Once screws are removed and ribbon cables are disconnected, lift the motherboard out.
Some wire connections are secured to the motherboard with hot glue. To completely remove the motherboard all wires must be disconnected. Removing such connections goes beyond the scope of this guide.

Editar