Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Usa una moneda para girar el tornillo de bloqueo de la batería 90 grados en sentido horario.
-
Saca la bateria del ordenador.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four Phillips screws from the memory door.
-
Slide the memory door away from the memory compartment.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 8 screws:
-
Two 3 mm Phillips in the battery compartment, on either side of the battery contacts.
-
Two 9 mm Phillips on either side of the memory compartment.
-
Four 16 mm Phillips along the hinge.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the computer 90 degrees clockwise, so that the power receptacle faces you.
-
Remove the three 3 mm Phillips screws.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer 90 degrees clockwise so that the hinge faces you.
-
Remove the bottom 5 mm Phillips screw on either side of the hinge (two total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the computer 90 degrees clockwise, so that the ports face you.
-
Remove the three 3 mm Phillips screws.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer over and open the display.
-
Remove the 4.2 mm 1/16" H 1.5 hex screws in either corner, next to the display (a T6 Torx driver will also do the job nicely).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the back corners of the upper case and pull up, disengaging hidden tabs on the sides. Do not pull the upper case off yet; you still need to free tabs in the front of the case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pry up the left side of the upper case slightly with your hand and wedge a spudger into the seam between the upper case and lower case.
-
Leave the tool in place applying pressure to the upper case for the next step.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Place enough pressure on the upper case to allow you to slide a tool just within the seam between upper case and lower case as shown in the picture. A dentist's hook, push pin, or similar tool will work.
-
Delicately slip the tip of your tool behind the silver metal latch and pull it forward while pulling up on the case. This may take some effort.
-
Alternatively, you can free the clasp with a small flathead screwdriver through the CD slot. The clasp is 1-3/16 in (3cm) from the left side of the slot. Use the screwdriver to lift out (or press back) the felt lining; then use the screwdriver to pull the clasp (shiny metal) forward to free it from the catch behind it (dull metal).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the back of the case up and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.
-
Rotate the upper case up and toward the screen, so that the upper case rests against it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the orange tape securing the trackpad ribbon to the logic board.
-
Disconnect the trackpad ribbon from the logic board.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Loosen the keyboard ribbon clamp by pushing the thin black piece toward the screen, using the tips of your fingers.
-
Slide the grey keyboard ribbon out of the loosened connector.
-
Remove the upper case from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the indicated 14 cables from the logic board, starting in one place and moving around the board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 12 Phillips screws from the logic board:
-
Six 4 mm around the edges of the logic board.
-
Two 5 mm securing the right speaker to the logic board (move the speaker off of the logic board).
-
Three 6 mm with wavy washers in the upper, left corner of the logic board.
-
One 4 mm underneath a black bumper in the back right corner of the logic board.
-
One 4 mm screw may not be present on some logic boards.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to gently (very gently) pry up the left side of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the DC-In connector from the left side of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the battery cable from the front, left corner of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the logic board at the left edge with one hand and at the thinnest section with the other hand. Lift the left edge of the board up to approximately a 30 degree angle (if you don't have your protractor handy, just lift until the DVI port clears the right hinge).
-
Once the logic board clears the ports, slide it out to the left.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a firm plastic edge to scrape the thermal material off the processor.
-
For more advanced instructions on this procedure, see our Applying Thermal Paste Guide.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a firm plastic edge to scrape the thermal material off the heat sink.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Apply a new layer of thermal paste to the copper heat conduit.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two black Phillips screws from the yellow plastic board above the USB port on the left side of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the black Phillips screw on the bottom corner of the left speaker board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the nut from the screw just in front of the left speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the speaker board up from the computer so that you can access and disconnect the speaker cable from the sound board.
-
Remove the speaker assembly entirely, including the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the Phillips screw from each corner of the PC card cage (4 screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the PC card cage up from the front, and remove it from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the Airport antenna cable at the black connector, making sure you pull only on the black rubber portion of the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two silver Phillips screws from either side of the large orange Airport ribbon, and remove the ribbon from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two small black Phillips screws from either side of the Airport card cage (4 screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the Airport card cage toward the display and out of the computer.
-
Cancelar: No complete esta guía.
6 personas más completaron esta guía.