Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove both expansion bay modules using the levers on the front of the computer.
-
Insert your index fingers inside the expansion bays and search for the two ribbed tabs on the underside of the upper case. The tabs are located near the bottom corners of the keyboard.
-
Pull the tabs toward yourself and the keyboard will pop up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the keyboard forward to disengage the tabs holding it in back and rotate it toward you.
-
Rest the keyboard on the trackpad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two keyboard connectors by disengaging the clamps and pulling the ribbons directly upward.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide a spudger downward between each plastic strain relief cable and the wall of the case in order to bow out the cable beyond the small tab holding it in place.
-
Once the strain relief cables are free, lift the keyboard off.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws from the heat shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the metal handle on the heat shield and pull up and toward yourself.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Unscrew, but do not remove, the single Phillips screw from the hard drive bracket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the hard drive bracket on the left side and pull up and to the left.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger, the tips of your fingers, or a flat non-metal tool to pry up the processor's right side.
-
Remove the processor by sliding it up and to the right.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single Phillips screw from the modem.
-
Disconnect the orange PMU cable by pulling it directly up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the modem from the logic board by lifting up on the right side using a spudger, the tip of your finger, or a flat non-metal tool.
-
Remove the modem by sliding it up and to the right.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push the display back so that it lies flat.
-
Slip a spudger or your index finger under the clutch cover near the power button and pull upward until you feel it come free.
-
Repeat the previous step on the left side.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the clutch cover off by rotating it up and then toward you.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the orange display data cable on the left side of the computer. Grasp the cable near the connector and pull directly up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the orange display inverter cable on the right side of the computer. Grasp the cable near the connector and pull directly up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the laptop around so that its back faces you.
-
Open the port door located at the back of the laptop.
-
Remove the four black T8 Torx screws.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the laptop back around so that the screen faces you.
-
Adjust the display so that it is in a vertical position.
-
Hold the display on both sides and pull directly up until its hinges are free of their mounts
-
Cancelar: No complete esta guía.
8 personas más completaron esta guía.
