Introducción
El error de lectura de disco es uno de los errores más comunes y posiblemente el más frustrante que te quizá te encuentres.
Este problema ocurre debido al polvo y/o la suciedad que pueden acumularse en la lente. Por suerte es sencillo de solucionar y simplemente requiere un par de sencillos pasos.
Qué necesitas
-
-
Utiliza la parte plana de una espátula metálica para hacer palanca y quitar las patas de goma que ocultan los tornillos.
-
Quita los siguientes ocho tornillos que aseguran la carcasa superior con la inferior.
-
Cuatro tornillos Phillips de 55.4 mm.
-
Cuatro tornillos Phillips de 18.0 mm.
-
-
-
Algunos modelos tienen un número diferentes de tornillos y patas de goma. Quita todos los que veas en la carcasa inferior.
-
El modelo que tiene 10 tornillos, tiene 6 en la parte inferior y 4 en la bandeja superior de la parte inferior. Échale un vistazo a la foto para que te quede más claro.
-
-
-
-
Levanta la carcasa superior de la carcasa inferior.
-
Con cuidado quita el cable de alimentación que une ambas mitades, para ello desconéctalo de la parte inferior de la carcasa.
If you have a 5000x model, then the power and reset buttons are attached to the console, not the lid. Therefore there won’t be a cord
-
-
-
Quita los cuatro tornillos Phillips de 6.4 mm que sujetan la tapa superior de la unidad de disco óptico.
-
Levanta y quita la tapa superior de la unidad de disco óptico.
On my ps2 there were only 2 screws near the front of the lid, it snapped into place in the back. I removed it by unscrewing the screws and gently pulling the back right corner (if the front is facing you) towards the front, it gently comes loose, then pulling the back left corner sideways and it came off
-
Para volver a montar tu PlayStation 2 sigue esta guía en orden inverso, desde el final hacia el principio.
Para volver a montar tu PlayStation 2 sigue esta guía en orden inverso, desde el final hacia el principio.
Cancelar: No complete esta guía.
63 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ MemoryOverflow nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
10 comentarios
I've tried the steps mentioned above to no avail. The problem persist. Anything else i can do besides purchasing another console? Sentimental value.Thank you.
What I'm gonna try and do is take a laser from a PC DVD burner tray and see if I reads things. It's a long shot but you can't break what's already broken ehh. I'll let you know what happens. And if it works I will write the proper tutorial for it:)
HOw to use a lens cleaner dvd in Ps2
please answer my problem
Best option is this doesn't work is to not use the disc reader at all. As far as the research I've done no one makes replacement lasers for PS2 yet...or rather very few do. I suggest using PS2 homebrew programs to run the games from a HDD attached to the network adapter. Even then the PS2 takes pata drives unless you use a converter and a laptop sata HDD or modify the network adapter itself...if your brave. I honestly haven't personally tried these things yet mind you I've just been researching it for a week or so.
Tried this to fix the Cant-read-DVDs-but-can-read-CDs problem, when I put it back together, it wouldn't power on again :(
Took it apart again to see if I unplugged something accidentally and it doesn't look like I did. I hope someone will tell me this is common and I just knocked something loose but I'm afraid my ps2 might have finally died. (I've had it since 2002 though, so not bad I guess?)
best way to fix DRE that I found was to take the laser lens off and clean the laser its self, what you done realize is dust gets under the glass lens, its a bit difficult in a way and patents is the key, there are 2 vary thin copper wires attached to the lens the copper wires are in between to magnets, and is held in place with some tacky goo, you have to be gentile but firm and lift the lens out, then take a q-tip (does not even have to be wet, best not to be you’ll be working right on top of the laser its self) and give it a few swipes. I have done this twice on 2 different ps2’s its works. No more adjustment the laser voltage (the adjustment was made to see better though the dust fyi). this is a proven method, just try it, if your to sacred to take about the laser, then dont, have someone else do it
How do you fix the red screen on ps2 tnx fore the answer..sir..
Before proceeding to step 2, Take a look at your PS2, some PS2's have 10 screws (and screw covers) instead of 8 (i found them underneath the optical drive), these instructions have mislead me and i ended up breaking my top cover for my PS2.
Tristan - Contestar
Ich möchte daraufhin weisen, daß es bei der SCPH-50004 zwei verschiedene Schraubabdeckungen gibt.
4x Kreuzförmig 4x rechteckig
Sowie eine silberne schraube die sich an der unterseite aufhöhe des Reset-Knopfes befindet.
Christian Lehnhardt - Contestar