Repara tus cosas Comunidad Tienda

Philips Sonicare DiamondClean Metal Brush Connector Replacement

Qué necesitas

  1. Philips Sonicare DiamondClean Metal Brush Connector Replacement, Case Replacement: paso 1, imagen 1 de 2 Philips Sonicare DiamondClean Metal Brush Connector Replacement, Case Replacement: paso 1, imagen 2 de 2

    • Pull the head from toothbrush.

    Editar

  2. Philips Sonicare DiamondClean Metal Brush Connector Replacement: paso 2, imagen 1 de 2 Philips Sonicare DiamondClean Metal Brush Connector Replacement: paso 2, imagen 2 de 2

    • Use a nylon spudger to pry the chrome cap at the bottom off.

    Editar

  3. Philips Sonicare DiamondClean Metal Brush Connector Replacement: paso 3, imagen 1 de 1

    • Use a nylon spudger to release the black tabs on either side of internals.

    Editar

  5. Philips Sonicare DiamondClean Metal Brush Connector Replacement: paso 4, imagen 1 de 2 Philips Sonicare DiamondClean Metal Brush Connector Replacement: paso 4, imagen 2 de 2

    • Put the metal head on a solid surface with handle perpendicular to the surface. Firmly, yet gently, push down until the internals start to slide out.

    Editar

  6. Philips Sonicare DiamondClean Metal Brush Connector Replacement, Metal Brush Connector Replacement: paso 5, imagen 1 de 1

    • Use a Phillips screwdriver to remove the screw at the base of the metal head.

    Editar

  7. Philips Sonicare DiamondClean Metal Brush Connector Replacement: paso 6, imagen 1 de 1
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    Comprar

    • Use fine tip tweezers to push the white plastic tabs in to release the head from the innards.

    Editar

  8. Philips Sonicare DiamondClean Metal Brush Connector Replacement: paso 7, imagen 1 de 1

    • Gently pull the metal head from the innards.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

9 personas más completaron esta guía.

Autor

con 3 otros colaboradores

Zachary Bertrand

Miembro Desde 11/20/17

821 Reputación

3 Guías creadas

Insignias: 14

+ 11 más insignias

Equipo

IUPUI, Team S22-G1, Bayer Fall 2017 Miembro de IUPUI, Team S22-G1, Bayer Fall 2017

IUPUI-BAYER-F17S22G1

4 Miembros

9 Guías creadas

7 comentarios

Great guide - but where is a good source for replacement parts?

Christian Zischek - Contestar

Ordered replacement part, came within 3 days at ebay. Didn’t have to replace the soft rubber inlet parts, only the connector.

Piece of cake, exchange of battery seems more labourous, but the brush still works for two weeks, so we postpone this job.

Emilio - Contestar

Gut beschrieben, aber wo bekomme ich eine neue Antriebsachse?

Beste Grüße - pechi606

Walter P - Contestar

Z.B. direkt aus China : ebay

VauWeh -

Great post, thank-you. One question: My toothbrush has a wire loop around the head. The loop is soldered to the circuit board. Do you know what that wire is for? Cheers!

tim belina - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 13

Ultimos 7 días: 87

Ultimos 30 días: 373

Todo El Tiempo: 17,284