Repara tus cosas

Derecho a reparar

Tienda

PSP 300x Power Board Replacement

Escrito Por: mbnewsom (y 10 de otros participantes)
  • Comentarios: 5
  • Favoritos: 13
  • Terminaciones: 2

Dificultad

Fácil

Pasos

13

Tiempo Requerido

15 minutos

Secciones

4

Banderas

2

Inconsistent Images

Imágenes Inconsistentes

Actualizando las imágenes de esta guía para que sean más consistente con los requisitos previos aumentaran su genialidad.

Better Introduction

Mejor introducción

Mejora esta guía completando o revisando su introducción.

Introducción

Guide for removing the power board in a Sony PSP-3000

  1. Place the PSP face down and locate the battery cover on the left side of the device. Lift and remove the battery cover to reveal the battery. Remove the battery.

    • Place the PSP face down and locate the battery cover on the left side of the device.

    • Lift and remove the battery cover to reveal the battery.

    • Remove the battery.

    Traducir

  2. Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

    • Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

    Traducir

  3. Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver. Two are located behind the battery's warranty sticker.

    • Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.

    • Two are located behind the battery's warranty sticker.

    • Two are located on the right side of the PSP.

    Traducir

  4. Next, unscrew the two screws located at the top of the PSP.

    • Next, unscrew the two screws located at the top of the PSP.

    Traducir

  5. Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

    • Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

    Traducir

  6. SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

    SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

  7. Slide the spudger in between the outer casing of the PSP, beginning at the "R" shoulder button, and gently pry off the casing.
 Remove the front casing completely.

    • Slide the spudger in between the outer casing of the PSP, beginning at the "R" shoulder button, and gently pry off the casing.


    • Remove the front casing completely.

    Traducir

  8. Push the homebar to the right to release the tab located on the right side of the LCD screen.

    • Push the homebar to the right to release the tab located on the right side of the LCD screen.

    • DO NOT completely remove the homebar, as it is still connected by ribbon cables.

    Traducir

  9. Slowly lift the LCD screen off the PSP starting at the top edge corner. Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

    • Slowly lift the LCD screen off the PSP starting at the top edge corner.

    • Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

    • Orientation of PSP is flipped in photo.

    Traducir

  10. Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail. Pull all four ribbon cables out.

    • Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.

    • Pull all four ribbon cables out.

    • Now remove the LCD screen and homebar from the PSP.

    Traducir

  11. Remove the metal tab that lies above the LCD screen.

    • Remove the metal tab that lies above the LCD screen.

    • Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

    Traducir

  12. Using a spudger, lift up the lock and remove the ribbon cable from the motherboard

    • Using a spudger, lift up the lock and remove the ribbon cable from the motherboard

    Traducir

  13. Use a Phillips #00 screwdriver to remove the screw located on the power switch board.

    • Use a Phillips #00 screwdriver to remove the screw located on the power switch board.

    Traducir

  14. Lift up and remove the power-switch board.

    • Lift up and remove the power-switch board.

    Traducir
Linea de Meta

2 personas más completaron esta guía.

Autor

con 10 otros colaboradores

mbnewsom

Miembro Desde 28/10/09

2,765 Reputación

11 Guías creadas

Insignias: 15

+ 12 más insignias

0 comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 19

Ultimos 30 días: 66

Todo El Tiempo: 13,648