Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide and push the battery casing to open it.
-
Push the battery to eject it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the camera so that you are facing the bottom of the camera.
-
Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws on the bottom of the camera.
-
Using a spudger, pry off the plating on the bottom of the camera.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the camera so that you are facing the top of the camera.
-
Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws located on the top of the camera.
-
Using a spudger, pry off the plating on the top of the camera.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the camera so the LCD is facing upwards.
-
Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws located on the left side of the device.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located next to the black "Olympus" face plate.
-
Using a T6 Torx screwdriver, unscrew the two 3.5mm screws located on the black "Olympus" face plate.
-
Using a spudger, gently pry off the black "Olympus" face plate.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws to the right of the cursor pad on the U-shaped frame.
-
Turn the device over so the front of the camera is facing you.
-
Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws on the end casing.
-
Using a spudger, pry off the end casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the camera so the blue face plate is visible.
-
Using a Phillips 00 screwdriver, unscrew the two 3mm screws on the blue plate.
-
Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located at the bottom of the camera straight down from the flash.
-
Using a spudger, gently pry off the blue face plate.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a Phillips 00 screwdriver, unscrew the 9mm screws on the top of the camera to the right of the flash.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a Phillips 00 screwdriver, unscrew the wide 3.5mm screw located in the middle of the camera.
-
Using a Phillips 00 screwdriver, unscrew the 9mm screw located at the top left corner of the camera.
-
Using a spudger, separate the black plate from the camera.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Tweezers$4.99-
Using tweezers, pull the white ribbon cable to disconnect it.
-
Using tweezers, pull the brown ribbon cable to disconnect it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the Phillips #00 Screwdriver, unscrew the 3.9mm screws on the back left side of the LCD screen case.
-
Using the spudger, gently pry the two screw holders from the LCD screen case.
-
Using your hands, gently push LCD through the LCD screen case.
-