Esta traducción podría no reflejar los cambios más recientes añadidos a la guía de referencia. Ayúdanos a actualizar la traducción o revisa la guía original.
Introducción
¿El reconocimiento de voz no funciona? ¿Gritarle a tu Nintendo 3DS XL con la esperanza de que el juego finalmente recoja tu voz? Esta guía te llevará a través de los pasos necesarios para instalar un nuevo micrófono para que puedas volver a jugar tus juegos favoritos en poco tiempo.
Qué necesitas
-
-
Afloja los dos tornillos Phillips #0 de 4,2 mm de longitud situados en la parte superior de la tapa posterior.
-
Los tornillos tienen arandelas (rondanas) de seguridad que evitan que los tornillos se desprendan de la cubierta . Deja las arandelas en los tornillos; no es necesario removerlas para esta guía de reparación.
-
-
-
Coloca el dispositivo de manera que la cubierta quede hacia arriba.
-
Usa una herramienta para abrir de plástico para desprender la cubierta empezando desde la esquina derecha.
-
Sostén la orilla de la cubierta para asegurarte de que no se cierre de nuevo.
-
Revisa la pequeña sección debajo del compartimiento del stylus. Manipula la cubierta en ese punto si aún no se ha desprendido.
-
Quita la cubierta del dispositivo y deja la batería a un lado.
Note that on the lower side (opposite to the hinges), there are small hooking tabs. These require you to lift the top (screw side) off towards you, then the lower area.
-
-
-
Inserta la herramienta para abrir de plástico en la apertura localizada en el lado derecho de la batería.
-
Empuja la bateria fuera de la carcasa.
-
Levanta y retira la bateria fuera de la carcasa.
My 👴 grandpa was helping me 🔧 repair my 3ds xl and ⚡️electrocuted himself with the 🔋battery while we was taking it out with a 🔪 knife. 💀 Rip grandpa 😔
-
-
-
Con unas pinzas, extrae los topes de goma que se encuentran en la parte superior del dispositivo a ambos lados del compartimento del cartucho de juego.
-
-
-
-
Con una herramienta de apertura de plástico, haz palanca en la carcasa inferior comenzando por el borde inferior y trabajando alrededor del perímetro.
-
Dos cables planos conectan la caja a la placa de circuito. Ten cuidado de no tirar demasiado fuerte de la carcasa y rasgar los cables planos.
-
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
4 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
90%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
2 comentarios
Hello! Do these instructions apply to the New 3DS XL as well? I followed steps from 1-8, but when I get to step 9, the layout is different and I can’t find the mic. Any help would be greatly appreciated!
please learn to repair the mic of new 3ds xl
Note: If your top or bottom screen was working before disassembly and doesn't work after reassembly, then it's likely that the connector is loose or dirty or damaged or not clipped or PLACED UPSIDE-DOWN. I had this issue with my Super3DS XL(2015) and it turns out that the reason why my top screen wasn't working after put together, was because I had the top LCD connector upside-down. After I correctly put the connector in, It worked again!
justjustintuber - Contestar
what type screwdriver do i use?!? its so small!!!!
Matthew - Contestar
I had success using a #00 Phillips head
Jake S -
Can't clip the front of the back cover back in
Macro Man - Contestar
I had trouble too, but got past it by slipping the bottom edge into the three indents first then easing the rest of the cover on!
Issu -
I found these were actually #00
Demosthien - Contestar
The screws in the 1st picture are stripped. What screwdriver head do I use?
Adric101 - Contestar