Introducción
La placa principal recoge toda la circuitería interna del modelo 2DS, y se debe extraer con sumo cuidado. Asegúrate de no estropear ningún tornillo, porque impediría extraer la placa.
Qué necesitas
-
-
Retire los dos tornillos cautivos Phillips que aseguran el panel superior trasero.
-
-
-
Retira los diez tornillos Phillips que sostienen el panel posterior de la consola.
Can't take off the screw top left next to the battery. What type of screwdriver do I use and where can I find some?
I used a husky with changeable heads, you could probably find one on amazon
-
-
-
-
Con cuidado, levanta el panel hacia arriba.
-
-
-
Usa tus uñas o la punta plana de una espátula para voltear el conector que asegura el cable plano a la tarjeta madre.
-
Remueve el cable del conector.
You can also detach the cable from the motherboard safely by flipping up the connector on the motherboard. Just don't forget to reattach. Some will find this tedious but may save time if you know what you're doing with said connectors.
I agree, this is what the guide i followed said to do and since I was disconnecting all the other ribbon cables it made perfect sense to do it that way.
Lin -
pay attention: my 2ds dropped it's lens covers at this step
Likewise, I used a tiny drop of glue to put the lens back in place. Take care not to dirty the lens.
The picture you have there has the camera lens ribbon installed upside down. The ribbon needs to be pointing down when you re-attach it not up.
Agreed, ribbon cable looks upside down in picture
-
-
-
Sujeta los paneles laterales con los dedos y retíralos hacia los lados.
-
Hay tres cables que ya han sido desconectados en esta foto, desconecta estos antes de desarmar el dispositivo después.
When reattaching during reassembly, take great care to ensure volume slider piece is correctly aligned with potentiometer tab on motherboard, otherwise volume control cannot be changed.
The are two small metal pins in the bottom corners of the case, take care not to misplace them.
The (3?) small ribbon cables on the bottom of the motherboard appear to already have been unplugged in this step. unplug them while unplugging the two large screen ribbon cables in step 10
What are the three ribbon cable at the bottom are supposed to be. Pls
-
-
-
Extrae los doce tornillos bronceados que sujetan la placa principal.
I dont know if its just me but my gold mother board screws i had a few that just didnt fit right with a ph000. Maybe my screw driver is just garbage?
-
-
-
Hay dos tornillos adicionales situados en el carril superior. Extráelos para sacar por completo el carril superior y los botones.
-
Hay dos tornillos sujetando la base del joystick que deben ser extraídos (Ten cuidado con el cable flexible que aún permanece conectado)
-
Sujeta el panel superior con los dedos y retíralo de la carcasa.
When reassembling, take care to ensure all buttons, and rubber button pads are located correctly BEFORE securing the motherboard.
-
-
-
Separa los dos cables flexibles liberando las pestañas negras que los sujetan.
-
Extrae el plástico rectangular y el cuadrado blanco que son parte del joystick (requiere algo de presión). Ambos están sujetos a la placa principal.
-
En algunos modelos, necesitarás extraer tres cables mas finos en la parte inferior de la pantalla. Están sujetos por pestañas. ¡SÉ CARIÑOSO!
-
Sujeta la placa principal por un lado, y extráela.
Don't forget to disconnect the two tiny ribbon cables on the bottom of the motherboard that attach to the microphone and home button.
What happens if I can't get the ribbons to reattach? Is the board broke irreparably?
What about the top 2 wires
Briana the 3 wires on bottom of board are covered under screen 2 step 10.
y e e t y e e t m y d u d e s ! ! ! ! ! ! ! ! ! !!n ! ! ! ! ! ! ! ! ! !
The motherboard of my 2017(I think) 2DS is definitely laid out differently than in this guide, be careful.
Cosa succede se i connettori dei 3 piccoli cavi piatti si dovessero rompere??
How do I flip up the two ribbons ( need help desperately)
-
Para montar este dispositivo, sigue estas instrucciones en orden inverso.
Para montar este dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
32 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
13 comentarios
o meu 2ds esta com um defeito que, quando eu aperto o botão de power ele liga e apos alguns segundo desliga e faz um pequeno barulho.
Would a jis #000 screw driver work better? As i tried a ph +000 and the gold motherboard screws just dont fit right
I have a question. After I replaced the mother board I have been having issues with it freezing after a couple mins running. Do you know why
I have a similar problem. After I replaced mine it will not open any app, and it does not show the status bar. Does anyone know why?
Now that I've removed the motherboard, how do I fix it? The instructible is great as far as it goes, but it doesn't go far enough
Fix what? You need to be more specific. I have to purchase a screen from China in order to fix mine.
I have a quarter inch metal pin left over. Don’t see it in any tutorials. Anyone know where it’s from?
I have the same thing, It came out when I was removing the back panel. I believe it was located towards the bottom of the panel. I’m scouring forums to see where it goes. Found this on Youtube! https://www.youtube.com/watch?v=qjoPIt5K... looks like it is just a reinforcement pin for a lanyard in the bottom corners.
Kwag -
where do i buy a motherboaRD
Depends on the country where you live. In Europe, some countries have apps (flesh market) where you will find used motherboards of Nintendo. (Wallapop, Vinted...)
For the rest of the world, you can try a l i e x p r e s s . c o m or similar.