Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.

Qué necesitas

  1. Este paso está sin traducir. Ayuda a traducirlo

    : paso 1, imagen 1 de 2 : paso 1, imagen 2 de 2
    Herramienta utilizada en este paso:
    SIM Card Eject Tool
    $2.99
    Comprar
    • Power off the phone, by long-pressing the power button and touching Power off.

    • Remove the SIM tray using the SIM Card Eject Tool.

    • This step is required in order to remove the back case.

  2. Este paso está sin traducir. Ayuda a traducirlo

    : paso 2, imagen 1 de 1
    Herramienta utilizada en este paso:
    T5 Torx Screwdriver
    $5.49
    Comprar
  3. Este paso está sin traducir. Ayuda a traducirlo

    : paso 3, imagen 1 de 3 : paso 3, imagen 2 de 3 : paso 3, imagen 3 de 3
    • Gently open the back case by prying along the edge of the cover, starting at a corner of the phone and circling around the phone using a plastic opening tool.

    • The opening process may take a few minutes. The plastic will make a light snapping noise as the back cover separates from the rest of the phone.

  4. Este paso está sin traducir. Ayuda a traducirlo

    : paso 4, imagen 1 de 2 : paso 4, imagen 2 de 2
    • Remove the two 1.8 mm Phillips screws holding down the battery connector.

    • Using a plastic opening tool, disconnect the battery cable from its socket on the motherboard.

  5. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 2 : paso 5, imagen 2 de 2
    Herramienta utilizada en este paso:
    Plastic Cards
    $2.99
    Comprar
    • Remove the blue tape that secures the white antenna cable to the battery.

    • Using a spudger, carefully disconnect the white antenna cable.

    • Carefully pry the battery out with a Plastic Opening Tool, starting at the top left-hand corner and working down towards the bottom right-hand corner.

    • If necessary, you can also use a plastic card to separate the battery from the metal midframe.

    • The battery is securely glued to the phone. When reinstalling the battery, press the battery firmly against the adhesive strip.

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 3 : paso 6, imagen 2 de 3 : paso 6, imagen 3 de 3
    • Remove the nine 4.6 mm Phillips #000 screws. Gently lift out the plastic cover.

    • The midframe is held in with two clips, one at either side. Use a plastic spudger to release each side and gently lift up and away.

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 2 : paso 7, imagen 2 de 2
    • Remove the two 4.8 mm screws that hold the speaker enclosure together using the Phillips 00 screwdriver.

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 2 : paso 8, imagen 2 de 2
    • Gently pry the speaker up and away from the back of the phone using a plastic opening tool, and lift it out of the phone.

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 3 : paso 9, imagen 2 de 3 : paso 9, imagen 3 de 3
    • Using a spudger, pop off the gray connector on the top right of the motherboard.

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 3 : paso 10, imagen 2 de 3 : paso 10, imagen 3 de 3
    • Gently lift the audio jack upwards and to the left to remove it from the motherboard.

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 2 : paso 11, imagen 2 de 2
    • The audio port will likely lift out together with the ambient light sensor rubber cap.

    • Remove the cap from the old part and move it to the new one. Ensure the cap stays in place when installing the new audio port into the phone.

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 3 : paso 12, imagen 2 de 3 : paso 12, imagen 3 de 3
    • Gently pry the metal tab up using a spudger, and lift up the disconnected black flap.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 3 : paso 13, imagen 2 de 3 : paso 13, imagen 3 de 3
    • With a spudger, carefully pry up the black tab connecting the camera to the motherboard.

    • Lift up the camera from the socket.

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 3 : paso 14, imagen 2 de 3 : paso 14, imagen 3 de 3
    • Remove the Sim Card and the Sim Card metal tray.

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 3 : paso 15, imagen 2 de 3 : paso 15, imagen 3 de 3
    • Remove the white antenna interconnect cable that attaches the motherboard to the bottom right-hand corner of phone by pulling on it gently.

  16. Este paso está sin traducir. Ayuda a traducirlo

    : paso 16, imagen 1 de 3 : paso 16, imagen 2 de 3 : paso 16, imagen 3 de 3
    • Remove the tab located in the bottom right-hand corner of the motherboard attaching the motherboard to the front display assembly using a spudger.

  17. Este paso está sin traducir. Ayuda a traducirlo

    : paso 17, imagen 1 de 2 : paso 17, imagen 2 de 2
    • Remove the last tab connecting the motherboard to the front display assembly located in the upper right-hand corner of the motherboard using a spudger.

    • Once this tab is removed, the flap will be free and will spring away from the motherboard.

  18. Este paso está sin traducir. Ayuda a traducirlo

    : paso 18, imagen 1 de 3 : paso 18, imagen 2 de 3 : paso 18, imagen 3 de 3
    • Using a spudger, gently lift up the motherboard from the front display assembly.

    • Carefully remove the motherboard using your hands.

  19. Este paso está sin traducir. Ayuda a traducirlo

    : paso 19, imagen 1 de 3 : paso 19, imagen 2 de 3 : paso 19, imagen 3 de 3
    • Grasp the daughterboard with tweezers.

    • Gently pull upwards to slide the connector out of the charging port housing.

    • Remove the daughterboard from the display assembly.

  20. Este paso está sin traducir. Ayuda a traducirlo

    : paso 20, imagen 1 de 1
    • Remove the power and volume button switches from the display assembly.

    • Compare your old display assembly to your replacement part and verify that they match. If there are any small components missing from the replacement display, transfer them over from you old display.

Linea de Meta

20 personas más completaron esta guía.

Julia List

Miembro Desde 04/21/15

5,610 Reputación

7 Guías creadas

3 comentarios

Great post. I just replaced the Display assembly of a Nexus 4 using this guide now.

Jeswin Simon - Contestar

Replaced the screen and battery. Did tear up the edges of the back a bit, but it's going in a case anyway.

aSquirl - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 5

Ultimos 7 días: 17

Ultimos 30 días: 33

Todo El Tiempo: 5,729